ASTM F2275-2010 Standard Practice for Treestand Manufacturer Quality Assurance Program《树架制造商质量保证计划的标准实施规程》.pdf

1、Designation: F2275 10An American National StandardStandard Practice forTreestand Manufacturer Quality Assurance Program1This standard is issued under the fixed designation F2275; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides minimum requirements for aquality assurance program.1.2 This standard does not purport

3、to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F2120 P

4、ractice for Testing Treestand Load CapacityF2121 Practice for Treestand LabelsF2122 Practice for Treestand Safety DevicesF2123 Practice for Treestand InstructionsF2124 Practice for Testing Treestand Ladder, Tripod Standand Climbing Stick Load CapacityF2125 Test Method for Treestand Static Stability

5、and Ad-herenceF2126 Test Method for Treestand Static Load CapacityF2128 Test Method for Treestand Repetitive Loading Ca-pabilityF2337 Test Method for Treestand Fall Arrest SystemF2531 Test Method for Load Capacity of Treestand Seats3. Significance and Use3.1 The purpose of this practice is to provid

6、e the minimumrequirements necessary for the establishment of a writtenquality assurance program for treestands and elevated huntingequipment.4. Drawing Control Procedure4.1 A procedure shall be in effect so that appropriatemanufacturing drawings, their engineering revisions, and re-lated documents a

7、re utilized for each project. These drawingsand documents must be retained as long as the product remainsin production or distribution and for a period of five (5) yearsafter distribution ends.5. Material Control Procedures5.1 Aprocedure shall be in effect to ensure that all materials,processes and

8、components, including raw materials, are inaccordance with the engineering specifications.5.1.1 This procedure shall provide purchasing personnelwith all the information required to order appropriate material.5.1.2 A receiving procedure shall be in effect so thatincoming material is checked against

9、purchasing specifica-tions.5.1.3 A procedure shall be in effect so that material in stockcan be properly identified for future use.5.1.4 Documentation on any material, process, or compo-nents certified shall be filed for reference.5.2 A procedure will be in effect to ensure that the finalassembly of

10、 each product has a permanent date code indicatingits date of manufacture.5.2.1 A date code shall be located on each final productassembly.5.2.2 The date code shall include as a minimum the last digitof the year and a code for the month or the week. (Example: forMarch, 2009 “39” or “C9” or “93” or “

11、9C”.) Any code thatis logical, consistent and able to be decoded by the manufac-turer is acceptable. Any product in production for ten years ormore with no changes will be required to add a third number sothat the last two digits of the year are known.5.2.3 Date codes shall be made permanent.6. Insp

12、ection6.1 A procedure shall be in effect so that appropriateinspections are made on manufactured parts and subassembliesto ensure conformance with engineering specifications.6.2 A procedure shall be in effect so that appropriateinspections are made on purchased components.6.3 A procedure shall be in

13、 effect so completed units areinspected prior to delivery.6.4 Nonconforming components shall be identified andevaluated for disposition as follows:6.4.1 Reworked components shall be re-inspected in accor-dance with 6.1, 6.2,or6.3 of this practice prior to use.1This practice is under the jurisdiction

14、 of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.16 onArchery Products.Current edition approved Aug. 1, 2010. Published September 2010. Originallyapproved in 2003. Last previous edition approved in 2008 as F2275 08. DOI:10.1520/F2275-10.2F

15、or referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C7

16、00, West Conshohocken, PA 19428-2959, United States.6.4.2 A component not suitable for use shall be altered ordisposed of to avoid accidental use.6.4.3 In some cases, a component may be determined to be“acceptable as is” or “as modified” after further evaluation. Insuch cases, appropriate review acc

17、eptance and documentationshall be a requirement.7. Testing and Compliance7.1 A procedure shall be in effect to insure that producttesting has been completed and that products comply with theminimum requirements of applicable ASTM standards.7.1.1 The latest revision of the following applicable testme

18、thods shall be met: Test Methods F2125, F2126, F2128,F2337, and F2531.7.1.2 The latest revision of the following applicable prac-tices shall be met: Practices F2120, F2121, F2122, F2123, andF2124.7.2 Test results and applicable documents must be retainedas long as the product remains in production o

19、r distribution andfor a period of five (5) years after distribution ends.8. Keywords8.1 climbing stick; compliance; specifications; treestand;tripod treestandAPPENDIX(Nonmandatory Information)X1.X1.1 This standard is provided for use by manufacturers oftreestands and testing companies. Criteria has

20、been developedfor certification of treestands and this standard is an integralpart of the certification. However, a treestand conforming tothis standard alone does not constitute certification, and thosemanufacturers desiring certification must meet all applicablestandards as a minimum requirement.A

21、STM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are

22、entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standard

23、sand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committe

24、e on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2275 102