ASTM F2275-2017 Standard Practice for Treestand Manufacturer Quality Assurance Program《木质平台生产厂质量保证大纲的标准实施规程》.pdf

1、Designation: F2275 10 (Reapproved 2014)F2275 17 An American National StandardStandard Practice forTreestand Manufacturer Quality Assurance Program1This standard is issued under the fixed designation F2275; the number immediately following the designation indicates the year oforiginal adoption or, in

2、 the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides minimum requirements for a quality assurance program.1.2 Thi

3、s standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to

4、 use.1.3 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers

5、to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2F2120 Practice for Testing Treestand Load CapacityF2121 Practice for Treestand Labels (Withdrawn 2017)3F2122 Practice for Treestand Safety Devices (Withdrawn 2017)3F2123 Practice for Treestand InstructionsF2124 Practice for Testing

6、Treestand Ladder, Tripod Stand and Climbing Stick Load Capacity (Withdrawn 2017)3F2125 Test Method for Treestand Static Stability and AdherenceF2126 Test Method for Treestand Static Load CapacityF2128 Test Method for Treestand Repetitive Loading CapabilityF2337 Test Method for Treestand Fall Arrest

7、SystemF2531 Test Method for Load Capacity of Treestand Seats3. Significance and Use3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written qualityassurance program for treestands and elevated hunting equipment.4. Drawing Control Procedure4

8、1 A procedure shall be in effect so that appropriate manufacturing drawings, their engineering revisions, and relateddocuments are utilized for each project. These drawings and documents must be retained as long as the product remains inproduction or distribution and for a period of five (5) years

9、after distribution ends.5. Material Control Procedures5.1 A procedure shall be in effect to ensure that all materials, processes and components, including raw materials, are inaccordance with the engineering specifications.5.1.1 This procedure shall provide purchasing personnel with all the informat

10、ion required to order appropriate material.5.1.2 A receiving procedure shall be in effect so that incoming material is checked against purchasing specifications.5.1.3 A procedure shall be in effect so that material in stock can be properly identified for future use.1 This practice is under the juris

11、diction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of SubcommitteeF08.18 on Treestands.Current edition approved Sept. 1, 2014Dec. 1, 2017. Published November 2014January 2018. Originally approved in 2003. Last previous edition approve

12、d in 20102014as F2275 10.F2275 10 (2014). DOI: 10.1520/F2275-10R14.10.1520/F2275-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary pa

13、ge on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be t

14、echnically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive,

15、PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.4 Documentation on any material, process, or components certified shall be filed for reference.5.2 A procedure will be in effect to ensure that the final assembly of each product has a permanent date code indicating its dateof manufact

16、ure.5.2.1 A date code shall be located on each final product assembly.5.2.2 The date code shall include as a minimum the last digit of the year and a code for the month or the week. (Example: forMarch, 2009 “39” or “C9” or “93” or “9C”.) Any code that is logical, consistent and able to be decoded by

17、 the manufactureris acceptable. Any product in production for ten years or more with no changes will be required to add a third number so that thelast two digits of the year are known.5.2.3 Date codes shall be made permanent.6. Inspection6.1 A procedure shall be in effect so that appropriate inspect

18、ions are made on manufactured parts and subassemblies to ensureconformance with engineering specifications.6.2 A procedure shall be in effect so that appropriate inspections are made on purchased components.6.3 A procedure shall be in effect so completed units are inspected prior to delivery.6.4 Non

19、conforming components shall be identified and evaluated for disposition as follows:6.4.1 Reworked components shall be re-inspected in accordance with 6.1, 6.2, or 6.3 of this practice prior to use.6.4.2 A component not suitable for use shall be altered or disposed of to avoid accidental use.6.4.3 In

20、 some cases, a component may be determined to be “acceptable as is” or “as modified” after further evaluation. In suchcases, appropriate review acceptance and documentation shall be a requirement.7. Testing and Compliance7.1 Aprocedure shall be in effect to insure that product testing has been compl

21、eted and that products comply with the minimumrequirements of applicable ASTM standards.7.1.1 The latest revision of the following applicable test methods shall be met: Test Methods F2125, F2126, F2128, F2337, andF2531.7.1.2 The latest revision of the following applicable practices shall be met: Pra

22、ctices F2120, F2121, F2122, F2123, and F2124.7.2 Test results and applicable documents must be retained as long as the product remains in production or distribution and fora period of five (5) years after distribution ends.7.3 A procedure shall be in place for products to maintain their compliance s

23、tatus until such a time that conditions should arisethat would warrant re-submission. Such conditions would include, but are not limited to: structural changes in regards to design,material components, manufacturer of products, or changes that would otherwise diminish or call into question the struc

24、turalintegrity, safety, or intended use, or a combination thereof, of the product. Changes to applicable test methods stated in 7.1.1 orpractices stated in 7.1.2, or both, may also warrant re-submission.8. Keywords8.1 climbing stick; compliance; specifications; treestand; tripod treestandAPPENDIX(No

25、nmandatory Information)X1. CONFORMANCE CRITERIA FOR TREESTANDSX1.1 This standard is provided for use by manufacturers of treestands and testing companies. Criteria has been developed forcertification of treestands and this standard is an integral part of the certification. However, a treestand confo

26、rming to this standardalone does not constitute certification, and those manufacturers desiring certification must meet all applicable standards as aminimum requirement.F2275 172ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item men

27、tionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee

28、 and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting

29、 of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO B

30、ox C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 173