ASTM F2406-2004(2012) Standard Practice for Determining Yield of Solid Ink Sticks《固态墨打印量测定的标准实施规程》.pdf

1、Designation: F2406 04 (Reapproved 2012)Standard Practice forDetermining Yield of Solid Ink Sticks1This standard is issued under the fixed designation F2406; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers a procedure to determine the yieldin number of pages per solid ink stick used in a solid ink/phasechange printe

3、r for printing an 8 by 10 in. image area on a lettersize page at 50 6 0.5 % fill of each individual color. Thispractice requires an accurate gram scale to weigh the solid inksticks and the printed pages, a personal computer able to printa506 0.5 % fill of each color, as well as a test printer.1.2 Th

4、is standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Def

5、initions of Terms Specific to This Standard:2.1.1 ink stick yield (Y)amount of pages that can beprinted from one ink stick.2.1.2 solid ink stickconsumable used in a hot-melt print-ing device to apply color to a page.3. Summary of Practice3.1 A solid ink/phase change printer utilizing a solid inkstic

6、k is set up to determine yield in number of pages per solidink stick used in a solid ink/phase change printer. A test pagewith 50 6 0.5 % print output of each color for control is used.The solid ink stick is weighed.Aspecified number of prints arecreated on the printer using the solid ink stick. The

7、 amount ofink used to print the specified number of sheets is calculated.The results can be used to estimate the total page yield per solidink stick at various percent coverages. A comparison can bemade between the solid ink stick used for the control and anyother solid ink stick tested using this p

8、ractice.4. Significance and Use4.1 This practice can be used for the evaluation of OEM andcompatible ink sticks.4.2 This practice is suitable for research and developmentand quality acceptance evaluations.4.3 This practice is suitable to extrapolate ink yield (Ye)ofeach color at other percent covera

9、ges (Ce) from the calculatedyield (Y) using the following formula (see Table 1):50% Coverage/Ce 5 Y/YeorYe 5 YCe!/50% Coverage5. Interferences5.1 This practice does not consider the effects of thecleaning mechanism and its use of ink in lowering the effectiveyield of the solid ink. During normal use

10、 the printer mayrequire the use of a cleaning cycle which will reduce theeffective yield of the solid ink stick. During this test the use ofthe cleaning cycle during the printing should be avoided.5.2 Changes in humidity and temperature will have an effecton the measurements of the paper being weigh

11、ed. Every effortshould be made to run the test in a controlled environment.5.3 When changing ink sticks from one test of the samecolor to another test of the same color, at least three times theamount of ink normally stored in the reservoir should be runthrough the printer to insure that ink is purg

12、ed from the system.6. Reagents and Materials6.1 Sufficient quantities of same lot paper, ink and otherprinter specific consumables should be available for consis-tency.6.2 A reference target that can be verified to print at 50 60.5 % coverage on an 8 by 10 in. image area on a letter sizepage.6.3 Agr

13、am scale with 0.1 g readability, 6000 g capacity, 0.1g repeatability, 6 0.2 g linearity and 8.5 by 11 in. platen areais required.7. Hazards7.1 There exist no unusual hazards related to this practice.8. Procedure8.1 Testing will be done with one color ink stick at a time.8.2 Select and weigh the soli

14、d ink stick to be tested.Weight = Wis.1This practice is under the jurisdiction of ASTM Committee F05 on BusinessImaging Products and is the direct responsibility of Subcommittee F05.03 onResearch.Current edition approved Oct. 1, 2012. Published November 2012. Originallyapproved in 2004. Last previou

15、s edition approved in 2004 as F240604. DOI:10.1520/F2406-04R12.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States18.3 Measure and record the temperature and humidity in thetest area.8.4 Set up the test printer. Set the printer to the fac

16、torydefault mode. Turn off any Energy Saver/Energy Star modes.Set printer attributes that might effect printing attributes tostandard settings.8.5 Paper used in this test should be from the same lot, ifpossible, and be conditioned in the printing environment for atleast 24 h.8.6 Run ten sets of 100

17、sheets each of conditioned paperusing the 50 % test target alternatively with ten sets of 100empty sheets of the same stock and lot. This should be doneusing optional high capacity trays if available to allow forcontinued printer operation.8.7 Measure the weight of the 10 sets of 100 pagesindividual

18、ly immediately upon completion of the printing ofeach set however at a maximum within1hofthetime thepages were printed.Additionally, to verify accuracy, the 10 setsof pages should be weighed together and compared with thesum of the 10 sets weighed individually. All weights are to thenearest 0.1 g.8.

19、8 Calculate the yield of an ink stick ( Y) using thefollowing formula:Wip/1000 5 Wis/YorY 5 1000Wis!/Wipwhere:Wip = weight of the ink on the 1000 sample of paperdetermined by Wpp Wpe,Wis = weight of original ink stick,Wpp = weight of paper after printing the 50 % test target on1000 pages, andWpe = w

20、eight of the paper after printing 1000 blank pages.9. Report9.1 Report test conditions (temperature and humidity), mea-sured weights of the solid ink sticks, printed paper weightempty, printed paper weight at 50 % coverage, printer setupconditions, printer identification and test target criteria- op

21、er-ating system, program used, driver used.10. Precision and Bias10.1 Repeatable results can be obtained given that the sameprinter is used and the same personal computer and settings areused.10.2 Additionally, repeatable and reproducible results canbe obtained between laboratories.11. Keywords11.1

22、computer printer; ink yield; phase change; solid inkASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rig

23、hts, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for

24、 revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing

25、 you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may

26、 be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Summary

27、ResultsNumber of pages printed at varying percents of coverageACTUAL5% 10% 25% 50%Cyan 1036.23 488.05 206.65 105.89Magenta 1000.00 527.88 223.62 110.04Yellow 1036.23 543.73 194.03 105.20Black 1048.15 518.32 214.39 107.81PROJECTED from results taken at 50 %Cyan 1058.90 529.45 211.78 105.89Magenta 1100.40 550.20 220.08 110.04Yellow 1052.00 526.00 210.40 105.20Black 1078.10 539.05 215.62 107.81F2406 04 (2012)2