ASTM F2441-2005 Standard Practice for Labeling of Backpacking and Mountaineering Tents and Bivouac Sacks《背负式帐蓬以及攀登帐蓬和露营袋标记的标准实施规程》.pdf

1、Designation: F 2441 05An American National StandardStandard Practice forLabeling of Backpacking and Mountaineering Tents andBivouac Sacks1This standard is issued under the fixed designation F 2441; the number immediately following the designation indicates the year oforiginal adoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice establishes requirements for the informa-tion that shall be permanently affi

3、xed to backpacking andmountaineering tents and bivouac sacks.2. Referenced Documents2.1 ANSI Standard:2ANSI Z535.4 Product Safety Signs and Labels2.2 CPIA Standard:3CPIA84 Specification for Flame-Resistant Materials Usedin Camping Tentage3. Terminology3.1 Definitions:3.1.1 backpacking and mountainee

4、ring tent, nportableshelter made primarily of fabric weighing less than 3 oz/yd2,designed to be carried by the occupants while backpacking ormountaineering.3.1.2 bivouac sack, nlightweight waterproof bag thatcovers one or more sleeping bags.3.1.3 bivy sack, nalso known as bivouac sack.4. Significanc

5、e and Use4.1 These warnings are intended as preventive measuresagainst most reported hazards. This practice may not apply toall tents or bivouac sacks, and should be modified appropri-ately.5. Procedure5.1 The recommended labels are shown in the figures below.The size of the tent label is not define

6、d, but should be readablein accordance with ANSI Z535.4 and based on the size of thetent.5.2 The tent label is not intended to replace the labelrequired by CPIA-84.6. Tent Label6.1 The caution sign and warning label are printed on anorange background 6 in. wide by 1 in. high, with the rest of thewor

7、ding on a white background. It is recommended that thelabel be sewn into the tent close to an entrance where the userwill easily see it.7. Bivouac Sack Label7.1 The recommended size of the bivy warning label is 2 in.wide by 4 in. long. The caution sign and “warning” are printedon an orange backgroun

8、d 2 in. wide by 1 in. wide, with the restof the wording on a white background. It is recommended thatthe label be sewn onto the bivy, on or close to a zipper whereit will be easily seen by a user.8. Keywords8.1 backpacking; bivouac sack; bivy sack; hazards; label;mountaineering; tent1This practice i

9、s under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.22 onCamping Softgoods.Current edition approved May 1, 2005. Published May 2005.2Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor

10、, New York, NY 10036.3Available from Industrial Fabrics Association International (IFAI), 345 CedarSt., Suite 800, St. Paul, MN 55101-1088.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.FIG. 1 Tent LabelF2441052FIG. 2 Bivouac Sack L

11、abelF2441053APPENDIXX1. RATIONALEX1.1 These labels are based on reports from users, andinclude the most commonly reported hazards. The labels weredeveloped with the cooperation of several manufacturers. Thelanguage was intentionally kept simple, and the icons areintended to be universally recognizab

12、le.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights,

13、are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional stan

14、dardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Comm

15、ittee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2441054