ASTM F2509-2006 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing《控制聚乙烯气体配送管和管道外径.pdf

1、Designation: F 2509 06An American National StandardStandard Specification forField-assembled Anodeless Riser Kits for Use on OutsideDiameter Controlled Polyethylene Gas Distribution Pipe andTubing1This standard is issued under the fixed designation F 2509; the number immediately following the design

2、ation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requi

3、rements and test methodsfor field-assembled anodeless riser kits for use with outsidediameter controlled polyethylene gas distribution pipe andtubing in sizes through 2 IPS as specified in specificationD 2513.1.2 The test methods described are not intended to beroutine quality control tests.1.3 This

4、 specification covers the types of field-assembledanodeless riser kits described in 3.2.2.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand not considered standard

5、.1.5 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in tables and figures), shall not be consideredas requirements of the standard.1.6 This standard does not purport to address all of thesafety concerns, if any, a

6、ssociated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A 513 Specification for Electric-Resistance-Welded Ca

7、rbonand Alloy Steel Mechanical TubingA 53/A 53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessD 638 Test Method for Tensile Properties of PlasticsD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 2513 Specification for Thermoplastic Gas Pressure Pip

8、e,Tubing, and FittingsF 412 Terminology Relating to Plastic Piping SystemsF 1948 Specification for Metallic Mechanical Fittings forUse on Outside Diameter Controlled Thermoplastic GasDistribution Pipe and Tubing2.2 ASME Standards3ASME Boiler and Pressure Vessel Code3ASME B1.20.1 Pipe Threads, Genera

9、l Purpose (Inch)4B31.8 Gas Transmission and Distribution Piping Systems2.3 Federal Regulations:4United States CFR, Title 49, Part 192 Pipeline SafetyRegulations2.4 UL Standard:5UL 360 Standard for Liquid-Tight Flexible Steel Conduit3. Terminology3.1 The gas industry terminology used in this specific

10、ationis in accordance with ASME B31.8 or the United States CFR,Title 49, Part 192, unless otherwise indicated.3.1.1 pipeused herein refers to both “pipe” and “tubing”unless specifically stated otherwise.3.1.2 gasused herein refers to any fuel gas unless specifi-cally stated otherwise.3.2 Definitions

11、Definitions are in accordance with Defini-tions F 412 unless otherwise specified. Abbreviations are inaccordance with Abbreviations D 1600 unless otherwise speci-fied.3.2.1 anodeless riser, na type of mechanical fitting whichis designed to transport gas from underground polyethylenepiping to above-g

12、round metallic piping. When properly in-stalled, polyethylene pipe is the gas carrier in the below groundportion of an anodeless riser and is protected by a metallic risercasing when it extends above ground level.3.2.2 field-assembled anodeless riser kit, nA kit contain-ing all of the elements requi

13、red to assemble an anodeless riser1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved April 1, 2006. Published April 2006.2For referenced ASTM standards, visit the ASTM we

14、bsite, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Av

15、e., New York, NY 10016-5990.4Available from the Superintendent of Documents, U.S. Government PrintingOffice, Washington, DC 20402.5Available from Underwriters Laboratories (UL), Corporate Progress, 333Pfingsten Rd., Northbrook, IL 60062.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C7

16、00, West Conshohocken, PA 19428-2959, United States.at the point of installation with the exception of the gas-carrying polyethylene pipe. It consists of, at a minimum, a risercasing and a riser adapter. These components may be eitherintegrally combined or include provisions for attachment toone ano

17、ther at the point of installation.3.2.3 mechanical fitting, na device for making a connec-tion between piping components that employs physical force todevelop a leak-tight seal, produce alignment, and provideresistance to pullout caused by axial loads.3.2.4 riser adapter, na type of mechanical fitti

18、ng used tojoin polyethylene pipe to a metallic piping connection (typi-cally a pipe thread). Riser adapters are sometimes referred to asservice head adapters.3.2.5 riser casing, nthe metallic, non-gas carrying portionof an anodeless riser that serves as a protective conduit for thepolyethylene pipe.

19、 It may be either rigid, flexible, or acombination of both.3.2.6 qualified installation instructions, na written proce-dure for making a plastic mechanical joint that has beendemonstrated will meet the requirements set forth in the UnitedStates CFR, Title 49, Part 192.283(b), and this standard.4. Ma

20、terials and Manufacture4.1 General:4.1.1 All materials of the riser kit shall meet the perfor-mance requirements of this specification and applicable refer-enced specifications. Specific materials referenced in thissection are common materials used in these types of products.Alternate materials prov

21、en to provide equal or better perfor-mance shall be acceptable.4.1.2 All burrs on metal components which could damagethe polyethylene piping during assembly shall either be re-moved or suitably covered with a protective device such as anID plastic sleeve, to preclude any damage to the polyethylenega

22、s piping.4.2 Riser Casings:4.2.1 Rigid riser casings shall be constructed of Specifica-tion A 53 or A 513 or equivalent metallic materials with aminimum nominal 0.065 in. (1.65 mm) wall thickness withinthe allowable tolerance ranges of the applicable metallic pipingspecification.4.2.2 Flexible riser

23、 casings shall be constructed of plasticcoated flexible metallic tubing providing a crush strength of notless than 1000 lbs. when tested in accordance with UL 360,section 11.1. The flexible tubing shall also be capable ofwithstanding a tensile pull of 300 lbs. force without breaking orunwinding when

24、 tested in accordance with UL 360, section10.5.4.3 Moisture Seal:4.3.1 The riser casing shall include a bushing or seal at thepoint where the PE pipe will enter the casing. This seal shallprotect the PE pipe from being damaged by the casing endduring field assembly and resist the entry of moisture i

25、nto thecasing interior after installation.4.4 Specifications outlining the properties of the field-assembled riser kit shall be available from the manufacturerupon request.5. Physical Properties5.1 Thread Requirements:5.1.1 All gas carrying pipe threads shall comply withASME B1.20.15.2 Bend Radius R

26、equirements:5.2.1 The bend radius of prebent rigid casings shall be suchthat the PE piping can be inserted during field-assemblywithout causing damage to the PE pipe.5.3 Coatings:5.3.1 Field-assembled riser kit coatings, if any, shall be asagreed upon between the buyer and seller.5.4 Welding Require

27、ments:5.4.1 All gas pressure containing factory welding shallcomply with the requirements of the ASME Boiler andPressure Vessel Code, Section IX or API 1104.6. Dimensions, Mass, and Permissible Variations6.1 Because of the varying designs, the actual spread ofdimensions is quite different from manuf

28、acturer to manufac-turer.Atable of dimensions and tolerances encompassing thesedifferences would be meaningless and without value and,therefore, are omitted from this specification.7. Design Qualification Requirements7.1 The riser adapter shall meet the requirements of Stan-dard Specification F 1948

29、 for category 1 mechanical fittings.7.2 Riser Adapter to Riser Casing Connection:7.2.1 The connection between the riser adapter and risercasing shall be demonstrated to withstand a pull force greaterthan 300 lbs. when tested in accordance with 8.2. Separation ofthe casing material from the riser ada

30、pter shall constitutefailure of this test. In designs where the riser casing isconstructed of a minimum of schedule 40 steel pipe and theconnection to the riser adapter is made using a standardASME B1.20.1 pipe thread, the design shall be considered tomeet the requirements of this section and no tes

31、ting is required.8. Test Methods8.1 General:8.1.1 Unless otherwise specified, prior to testing, conditionall samples at an ambient temperature of 67 6 10F (19.4 65.6C) for not less than 4 h.8.1.2 Unless otherwise specified, the test conditions shall be67 6 10F (19.4 6 5.6C).8.1.3 Unless otherwise sp

32、ecified, the number of specimensshall be six.8.2 Tensile Pull TestingRiser Adapter to Casing Connec-tion:8.2.1 Conduct this test on each different riser adapter to risercasing connection. For kits where this connection is intended tobe assembled at the point of installation, it shall be assembledin

33、accordance with the manufacturers installation procedures.8.2.2 No polyethylene pipe shall be assembled within theriser kit while conducting this test.8.2.3 Affix the connection to be tested in a tensile apparatusin accordance with Test Method D 638. The equipment shall becapable of subjecting the j

34、oint to a constant pull at the ratespecified in section 8.2.5.F25090628.2.4 The minimum length of casing material shall be 6 in.(15.2 cm).8.2.5 Tensile pull test the connection at a constant pull rateof 0.2 6 25 % in./min. (5 6 25 % mm/min).9. Product Instructions9.1 Qualified installation instructi

35、ons shall be availablefrom the manufacturer and supplied with the field-assembledriser kit.10. Product Marking10.1 If the riser adapter and riser casing comprising thefield-assembled anodeless riser kit are integrally combined,they shall be marked with the following:10.1.1 The manufacturers name or

36、trademark.10.1.2 A marking that is traceable (by the manufacturer) toa date, or date range of manufacture.10.1.3 The nominal PE pipe size (including IPS or CTSdesignation) or the actual OD dimension (in inches), and eitherthe wall thickness (in inches) or dimension ratio of thepolyethylene pipe end

37、connection.10.1.4 The material designation PE indicating the riser hasbeen qualified for use with polyethylene pipe by the manufac-turer.10.1.5 This designation: F 2509.10.2 If the riser adapter and riser casing comprising thefield-assembled anodeless riser kit are supplied as separatecomponents (no

38、t integrally combined,) they shall be marked asindicated below:10.2.1 The riser adapter shall be marked as required byASTM F 1948.10.2.2 The riser casing shall be marked with the following:10.2.2.1 The manufacturers name or trademark.10.2.2.2 A marking that is traceable (by the manufacturer)to a dat

39、e, or date range of manufacture.10.2.2.3 This designation: F 2509.11. Quality Assurance11.1 When the product is marked with this designation,F 2509, the manufacturer affirms that the product was manu-factured, inspected, sampled and tested in accordance with thisspecification and has been found to m

40、eet the requirements ofthis specification.12. Keywords12.1 gas; service head adapter; SHA; field-assembled riser;anodeless riser; fuel gas piping; plastic gas piping; mechanicalfitting; riser adapter; riser casingASTM International takes no position respecting the validity of any patent rights asser

41、ted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by

42、the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receiv

43、e careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Intern

44、ational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2509063