ASTM F2509-2006(2012) Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing《外径受控的聚乙烯煤.pdf

1、Designation: F2509 06 (Reapproved 2012)An American National StandardStandard Specification forField-assembled Anodeless Riser Kits for Use on OutsideDiameter Controlled Polyethylene Gas Distribution Pipe andTubing1This standard is issued under the fixed designation F2509; the number immediately foll

2、owing the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specificati

3、on covers requirements and test methodsfor field-assembled anodeless riser kits for use with outsidediameter controlled polyethylene gas distribution pipe andtubing in sizes through 2 IPS as specified in specificationD2513.1.2 The test methods described are not intended to beroutine quality control

4、tests.1.3 This specification covers the types of field-assembledanodeless riser kits described in 3.3.2.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand not consi

5、dered standard.1.5 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in tables and figures), shall not be consideredas requirements of the standard.1.6 This standard does not purport to address all of thesafety conce

6、rns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A513 Specification for Electric-Resista

7、nce-Welded Carbonand Alloy Steel Mechanical TubingA53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessD638 Test Method for Tensile Properties of PlasticsD1600 Terminology for Abbreviated Terms Relating toPlasticsD2513 Specification for Polyethylene (PE) Gas

8、PressurePipe, Tubing, and FittingsF412 Terminology Relating to Plastic Piping SystemsF1948 Specification for Metallic Mechanical Fittings forUse on Outside Diameter Controlled Thermoplastic GasDistribution Pipe and Tubing2.2 ASME Standards:3ASME Boiler and Pressure Vessel Code3ASME B1.20.1 Pipe Thre

9、ads, General Purpose (Inch)4B31.8 Gas Transmission and Distribution Piping Systems2.3 Federal Regulations:4United States CFR, Title 49, Part 192 Pipeline SafetyRegulations2.4 UL Standard:5UL 360 Standard for Liquid-Tight Flexible Steel Conduit3. Terminology3.1 The gas industry terminology used in th

10、is specificationis in accordance with ASME B31.8 or the United States CFR,Title 49, Part 192, unless otherwise indicated.3.1.1 pipeused herein refers to both “pipe” and “tubing”unless specifically stated otherwise.3.1.2 gasused herein refers to any fuel gas unless specifi-cally stated otherwise.3.2

11、DefinitionsDefinitions are in accordance with Termi-nology F412 unless otherwise specified. Abbreviations are inaccordance with Terminology D1600 unless otherwise speci-fied.3.3 Definitions:3.3.1 anodeless riser, na type of mechanical fitting whichis designed to transport gas from underground polyet

12、hylenepiping to above-ground metallic piping. When properly in-stalled, polyethylene pipe is the gas carrier in the below groundportion of an anodeless riser and is protected by a metallic risercasing when it extends above ground level.1This specification is under the jurisdiction of ASTM Committee

13、F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved Feb. 1, 2012. Published February 2012. Originallyapproved in 2006. Last previous edition approved in 2006 as F250906. DOI:10.1520/F2509-06R12.2For referenced ASTM standards, visit the

14、 ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three

15、 Park Ave., New York, NY 10016-5990, http:/www.asme.org.4Available from the Superintendent of Documents, U.S. Government PrintingOffice, Washington, DC 20402.5Available from Underwriters Laboratories (UL), 2600 N.W. Lake Rd., Camas,WA 98607-8542, http:/.1Copyright ASTM International, 100 Barr Harbor

16、 Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.3.2 field-assembled anodeless riser kit, nA kit contain-ing all of the elements required to assemble an anodeless riserat the point of installation with the exception of the gas-carrying polyethylene pipe. It consists of, at a mi

17、nimum, a risercasing and a riser adapter. These components may be eitherintegrally combined or include provisions for attachment toone another at the point of installation.3.3.3 mechanical fitting, na device for making a connec-tion between piping components that employs physical force todevelop a l

18、eak-tight seal, produce alignment, and provideresistance to pullout caused by axial loads.3.3.4 riser adapter, na type of mechanical fitting used tojoin polyethylene pipe to a metallic piping connection (typi-cally a pipe thread). Riser adapters are sometimes referred to asservice head adapters.3.3.

19、5 riser casing, nthe metallic, non-gas carrying portionof an anodeless riser that serves as a protective conduit for thepolyethylene pipe. It may be either rigid, flexible, or acombination of both.3.3.6 qualified installation instructions, na written proce-dure for making a plastic mechanical joint

20、that has beendemonstrated will meet the requirements set forth in the UnitedStates CFR, Title 49, Part 192.283(b), and this standard.4. Materials and Manufacture4.1 General:4.1.1 All materials of the riser kit shall meet the perfor-mance requirements of this specification and applicable refer-enced

21、specifications. Specific materials referenced in thissection are common materials used in these types of products.Alternate materials proven to provide equal or better perfor-mance shall be acceptable.4.1.2 All burrs on metal components which could damagethe polyethylene piping during assembly shall

22、 either be re-moved or suitably covered with a protective device such as anID plastic sleeve, to preclude any damage to the polyethylenegas piping.4.2 Riser Casings:4.2.1 Rigid riser casings shall be constructed of Specifica-tion A53/A53M or A513 or equivalent metallic materials witha minimum nomina

23、l 0.065 in. (1.65 mm) wall thickness withinthe allowable tolerance ranges of the applicable metallic pipingspecification.4.2.2 Flexible riser casings shall be constructed of plasticcoated flexible metallic tubing providing a crush strength of notless than 1000 lbs. when tested in accordance with UL

24、360,section 11.1. The flexible tubing shall also be capable ofwithstanding a tensile pull of 300 lbs. force without breaking orunwinding when tested in accordance with UL 360, section10.5.4.3 Moisture Seal:4.3.1 The riser casing shall include a bushing or seal at thepoint where the PE pipe will ente

25、r the casing. This seal shallprotect the PE pipe from being damaged by the casing endduring field assembly and resist the entry of moisture into thecasing interior after installation.4.4 Specifications outlining the properties of the field-assembled riser kit shall be available from the manufacturer

26、upon request.5. Physical Properties5.1 Thread Requirements:5.1.1 All gas carrying pipe threads shall comply withASME B1.20.15.2 Bend Radius Requirements:5.2.1 The bend radius of prebent rigid casings shall be suchthat the PE piping can be inserted during field-assemblywithout causing damage to the P

27、E pipe.5.3 Coatings:5.3.1 Field-assembled riser kit coatings, if any, shall be asagreed upon between the buyer and seller.5.4 Welding Requirements:5.4.1 All gas pressure containing factory welding shallcomply with the requirements of the ASME Boiler andPressure Vessel Code, Section IX or API 1104.6.

28、 Dimensions, Mass, and Permissible Variations6.1 Because of the varying designs, the actual spread ofdimensions is quite different from manufacturer to manufac-turer.Atable of dimensions and tolerances encompassing thesedifferences would be meaningless and without value and,therefore, are omitted fr

29、om this specification.7. Design Qualification Requirements7.1 The riser adapter shall meet the requirements of Stan-dard Specification F1948 for category 1 mechanical fittings.7.2 Riser Adapter to Riser Casing Connection:7.2.1 The connection between the riser adapter and risercasing shall be demonst

30、rated to withstand a pull force greaterthan 300 lbs. when tested in accordance with 8.2. Separation ofthe casing material from the riser adapter shall constitutefailure of this test. In designs where the riser casing isconstructed of a minimum of schedule 40 steel pipe and theconnection to the riser

31、 adapter is made using a standardASME B1.20.1 pipe thread, the design shall be considered tomeet the requirements of this section and no testing is required.8. Test Methods8.1 General:8.1.1 Unless otherwise specified, prior to testing, conditionall samples at an ambient temperature of 67 6 10F (19.4

32、 65.6C) for not less than 4 h.8.1.2 Unless otherwise specified, the test conditions shall be67 6 10F (19.4 6 5.6C).8.1.3 Unless otherwise specified, the number of specimensshall be six.8.2 Tensile Pull TestingRiser Adapter to Casing Connec-tion:8.2.1 Conduct this test on each different riser adapter

33、 to risercasing connection. For kits where this connection is intended tobe assembled at the point of installation, it shall be assembledin accordance with the manufacturers installation procedures.8.2.2 No polyethylene pipe shall be assembled within theriser kit while conducting this test.8.2.3 Aff

34、ix the connection to be tested in a tensile apparatusin accordance with Test Method D638. The equipment shall becapable of subjecting the joint to a constant pull at the ratespecified in section 8.2.5.F2509 06 (2012)28.2.4 The minimum length of casing material shall be 6 in.(15.2 cm).8.2.5 Tensile p

35、ull test the connection at a constant pull rateof 0.2 6 25 % in./min. (5 6 25 % mm/min).9. Product Instructions9.1 Qualified installation instructions shall be availablefrom the manufacturer and supplied with the field-assembledriser kit.10. Product Marking10.1 If the riser adapter and riser casing

36、comprising thefield-assembled anodeless riser kit are integrally combined,they shall be marked with the following:10.1.1 The manufacturers name or trademark.10.1.2 A marking that is traceable (by the manufacturer) toa date, or date range of manufacture.10.1.3 The nominal PE pipe size (including IPS

37、or CTSdesignation) or the actual OD dimension (in inches), and eitherthe wall thickness (in inches) or dimension ratio of thepolyethylene pipe end connection.10.1.4 The material designation PE indicating the riser hasbeen qualified for use with polyethylene pipe by the manufac-turer.10.1.5 This desi

38、gnation: F2509.10.2 If the riser adapter and riser casing comprising thefield-assembled anodeless riser kit are supplied as separatecomponents (not integrally combined,) they shall be marked asindicated below:10.2.1 The riser adapter shall be marked as required byASTM F1948.10.2.2 The riser casing s

39、hall be marked with the following:10.2.2.1 The manufacturers name or trademark.10.2.2.2 A marking that is traceable (by the manufacturer)to a date, or date range of manufacture.10.2.2.3 This designation: F2509.11. Quality Assurance11.1 When the product is marked with this designation,F2509, the manu

40、facturer affirms that the product was manu-factured, inspected, sampled and tested in accordance with thisspecification and has been found to meet the requirements ofthis specification.12. Keywords12.1 gas; service head adapter; SHA; field-assembled riser;anodeless riser; fuel gas piping; plastic ga

41、s piping; mechanicalfitting; riser adapter; riser casingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent

42、 rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either

43、 for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hea

44、ring you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard

45、 may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2509 06 (2012)3