ASTM F2640-2007 Standard Consumer Safety Specification for Booster Seats《调节座椅用消费者安全标准规范》.pdf

1、Designation: F 2640 07Standard Consumer Safety Specification forBooster Seats1This standard is issued under the fixed designation F 2640; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parent

2、heses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification addresses incidents associated with booster seats that wereidentified by the United States Consumer Product Safety

3、Commission (CPSC). CPSC has identifiedhazards resulting in injuries that occurred when children fell from booster seats, tipped over and outof a booster seat, among other types of incidents. In response to a review of the data received by theCPSC, this specification attempts to minimize the followin

4、g: incidents related to tray disengagement,restraint disengagement or absence of restraint system, stability of a booster seat while attached toadult chairs and entrapment within a booster seat, in addition to other hazards presented during the useof booster seats. This specification does not cover

5、booster seats that were either blatantly misused orused in a careless manner that disregards the warning statements and safety instructions provided witheach booster seat. This specification is written within the current state-of-the-art of booster seattechnology. It is intended that this specificat

6、ion will be updated whenever substantive informationbecomes available that necessitates additional requirements or justifies the revision of the existingrequirements.1. Scope1.1 This consumer safety specification covers the perfor-mance requirements and methods of test to ensure the satis-factory pe

7、rformance of the booster seat.1.2 This consumer safety specification is intended to mini-mize injuries to children resulting from normal usage andreasonably foreseeable misuse or abuse of booster seats.NOTE 1This consumer safety specification is not intended to addressaccidents and injuries resultin

8、g from the interaction of older children withchildren in booster seats or the accidents resulting from normal use andreasonably foreseeable misuse or abuse.1.3 For purposes of this consumer safety specification, abooster seat is a juvenile chair, which is placed on an adultchair to elevate a child t

9、o standard dining table height. Thebooster seat is made for the purpose of containing a child, upto 5 years of age, and normally for the purposes of feeding oreating. A booster seat may be height adjustable and include areclined position.1.4 No booster seat produced after the approval date of thisco

10、nsumer safety specification shall, either by label or othermeans, indicate compliance with this specification unless itconforms to all requirements contained herein.1.5 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to

11、 SI units that are provided for information onlyand are not considered standard.1.6 The following precautionary caveat pertains only to thetest method portion, Section 7, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is

12、 the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 3359 Test Methods for Measuring Adhesion by Tape TestF 963 Consumer Safety Specific

13、ation for Toy Safety2.2 Federal Regulations:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint16 CFR 1500.48 Technical Requirements for Determining a1This consumer safety specification is under the jurisdiction of ASTM Commit-tee F15 on Consumer Prod

14、ucts and is the direct responsibility of SubcommitteeF15.16 on Highchairs, Hook-On Chairs and Expandable Gates.Current edition approved Sept. 15, 2007. Published October 2007.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For

15、 Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.1Copyright ASTM Interna

16、tional, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Sharp Point in Toys or Other Articles Intended for Use byChildren Under Eight Years of Age16 CFR 1500.49 Technical Requirements for Determining aSharp Metal or Glass Edge in Toys or Other ArticlesIntended for

17、 Use by Children Under Eight Years of Age16 CFR 1500.50-.52 Test Methods for Simulating Use andAbuse of Toys and Other Articles Intended for Use byChildren16 CFR 1501 Method for Identifying Toys and OtherArticles Intended for Use by Children Under Three Yearsof Age Which Present Choking, Aspiration,

18、 or IngestionHazards Because of Small Parts3. Terminology3.1 Definitions of Terms Specific to This Standard:3.2 conspicuous, nlabel which is visible, when the prod-uct is in the manufacturers recommended use position, to aperson standing at the sides or front of the booster seat.3.3 fabric, nany wov

19、en, knit, coated, laminated, extrudedor calendered flexible material that is intended to be sewn,welded, heat sealed, or glued together as an assembly.3.4 manufacturers recommended use position, nany po-sition that is presented as a normal, allowable, or acceptableconfiguration for the use of the pr

20、oduct by the manufacturer inany descriptive or instructional literature.3.4.1 DiscussionThis specifically excludes positions thatthe manufacturer shows in a like manner in its literature to beunacceptable, unsafe, or not recommended.3.5 nonpaper label, nany label material, such as plastic ormetal, w

21、hich either will not tear without the aid of tools or tearsleaving a sharply defined edge.3.6 occupant, nindividual who is in a product that is setup in one of the manufacturers recommended use positions.3.7 paper label, nany label material which tears withoutthe aid of tools and leaves a fibrous ed

22、ge.3.8 seam, nmeans of joining fabric components, such assewing, welding, heat sealing or gluing.3.9 static load, nvertically downward force applied by acalibrated force gauge or by dead weights.4. Calibration and Standardization4.1 All testing shall be conducted on a concrete floor thatmay be cover

23、ed with18 in. (3 mm) thick vinyl flooringcovering, unless test instructs differently.4.2 The product shall be completely assembled, unlessotherwise noted, in accordance with the manufacturers in-structions.4.3 No testing shall be conducted within 48 h of manufac-turing.4.4 The product to be tested s

24、hall be in a room with ambienttemperature of 73 6 9F (23 6 5C) for at least 1 h prior totesting. Testing shall then be conducted within this temperaturerange.4.5 All testing required by this specification shall be con-ducted on the same unit.5. General Requirements5.1 There shall be no hazardous sha

25、rp points or edges asdefined by 16 CFR 1500.48 and 16 CFR 1500.49 before orafter testing to this consumer safety specification.5.2 There shall be no small parts as defined by 16 CFR 1501before testing or liberated as a result of testing to thisspecification.5.3 Wood PartsPrior to testing, any expose

26、d wood partsshall be smooth and free from splinters.5.4 PaintThe paint and surface coating on the productshall comply with 16 CFR 1303.5.5 Scissoring, Shearing, and PinchingA product, whenin a manufacturers recommended use position, shall bedesigned and constructed so as to prevent injury to theoccu

27、pant from any scissoring, shearing, or pinching whenmembers or components rotate about a common axis orfastening point, slide, pivot, fold, or otherwise move relative toone another. Scissoring, shearing, or pinching that may causeinjury shall not be permissible when the edges of any rigidparts admit

28、 a probe greater than 0.210 in. (5.33 mm) and lessthan 0.375 in. (9.53 mm) diameter at any accessible pointthroughout the range of motion of such parts.5.6 OpeningsHoles or slots that extend entirely through awall section of any rigid material less than 0.375-in. (9.53-mm)thick and admit a 0.210-in.

29、 (5.33-mm) diameter rod shall alsoadmit a 0.375-in. (9.53-mm) diameter rod. Holes or slots thatare between 0.210 in. (5.33 mm) and 0.375 in. (9.53 mm) andhave a wall thickness less than 0.375 in. (9.53 mm) but arelimited in depth to 0.375 in. (9.53 mm) maximum by anotherrigid surface shall be permis

30、sible (see Fig. 1). The product shallbe evaluated in all manufacturers recommended us positions.5.7 Exposed Coil SpringsAny exposed coil spring whichis accessible to the occupant, having or capable of generatinga space between coils of 0.210 in. (5.33 mm) or greater duringstatic load testing in acco

31、rdance with 6.3 shall be covered orotherwise designed to prevent injury from entrapment.5.8 Protective ComponentsIf a child can grasp compo-nents between the thumb and forefinger, or teeth, (such as caps,sleeves, or plugs used for protection from sharp edges, points,or entrapment of fingers or toes)

32、, or if there is at least a0.040 in. (1.00 mm) gap between the component and itsadjacent parent component, such component shall not beremoved when tested in accordance with 7.1.5.9 Labeling:5.9.1 Warning labels (whether paper or non paper) shall bepermanent when tested in accordance with 7.8.1-7.8.3

33、.5.9.2 Warning statements applied directly onto the surfaceof the product by hot stamping, heat transfer, printing, woodburning, etc. shall be permanent when tested in accordancewith 7.8.4.5.9.3 Non-paper labels shall not liberate small parts whentested in accordance with 7.8.5.5.10 ToysToy accessor

34、ies attached to, removable from, orsold with a booster seat seat, as well as their means ofattachment, must meet applicable requirements of ConsumerSafety Specification F 963.F 2640 0726. Performance Requirements6.1 Tray Performance (Drop)The tray shall remain func-tional with respect to the booster

35、 seat and exhibit no sharppoints, sharp edges, or small parts when subjected to a drop testin accordance with 7.2.6.2 Tray Performance (Pull)The tray shall not becomedisengaged or dislocated from its original adjustment position,when tested in accordance with 7.3 and 7.4.6.3 Static LoadA booster sea

36、t shall support static loadswithout causing any hazardous conditions as identified withinthis consumer safety specification. Tests shall be conducted inaccordance with 7.5.6.4 Child Restraint System:6.4.1 Booster seats which are age graded for children lessthan 36 months shall provide a child restra

37、int system to securea child in any of the manufacturers recommended use posi-tions.6.4.2 The child restraint system shall include both waist andcrotch restraint designed such that the use of the crotchrestraints is mandatory when the restraint system is in use.FIG. 1 Openings ExamplesF 2640 0736.4.3

38、 The child restraint system and its closing means (forexample, buckle) shall not break, separate, or permit removalof the CAMI Infant Dummy Mark II4(see Fig. 2), from thebooster seat when tested in accordance with 7.6.6.4.4 If during test in 7.6.4.1 and 7.6.4.2, the posterior of thetest dummy is pul

39、led past the front edge of the seat, the dummyshall be considered removed.6.4.5 If during test in 7.6.4.3 and 7.6.4.4 the dummy withthe force applied reaches a vertical position with the bottom ofits feet touching or off the seat, the dummy shall be consideredremoved.6.4.6 The waist restraint shall

40、be capable of adjustment witha positive, self-locking mechanism that is capable, whenlocked, of withstanding the forces of tests in 7.6.4 withoutallowing restraint movement or slippage of more than 1 in.(25.4 mm).6.4.7 A connecting means and adjustment means for thewaist restraint shall be capable o

41、f usage independent of oneanother. The connecting means shall not be an adjustmentmeans but may have one integrally attached to it.6.4.8 Before shipment, the child restraint system must beattached to the booster seat in such a manner as to not becomedetached through normal use.6.5 Booster Seat Attac

42、hment:6.5.1 There shall be a means of attaching a booster seat to anadult chair.6.6 Structural Integrity:6.6.1 During and upon completion of the testing in accor-dance with 7.7, the booster seat shall comply with all of thefollowing:6.6.1.1 The booster seat shall not exhibit an instantaneouschange i

43、n the height of the occupant seating surface above theseating surface of the adult chair of more than 1 in. (25.4 mm)during one cycle of the weight drop. During and after a changein the height of the seating surface, the booster seat mustcomply with the requirements for openings as defined in 5.6and

44、 scissoring, shearing, and pinching as defined in 5.5.6.6.1.2 There shall be no breakage of any structural com-ponent.6.6.1.3 Latching or locking devices which prevent foldingor adjustment of the booster seat shall remain engaged.6.6.1.4 The angle of the occupant seating surface relative tothe seati

45、ng surface of the adult chair shall not change more than10.7. Test Methods7.1 Protective Components:7.1.1 Test all components in accordance with each of thefollowing methods in the sequence listed.7.1.2 Secure the booster seat so that it cannot move duringthe performance of the following tests.7.1.3

46、 Torque TestApply a torque of 4 lbf-in. (0.5Nm)gradually within a period of5sinaclockwise direction untila rotation of 180 from the original position has been attainedor 4 lbf-in. (0.5Nm)hasbeen reached. Maintain the torqueor maximum rotation for an additional 10 s. Then remove thetorque and permit

47、the test components to return to a relaxedcondition. Then repeat this procedure in the counter clockwisedirection.7.1.4 Tension Test:7.1.4.1 Attach a force gauge to the component cap, sleeve orplug by means of any suitable device. For components thatcannot reasonably be expected to be grasped betwee

48、n thumband forefinger, or teeth, on their outer diameter but have a gapof 0.04 in. (1.0 mm) or more between the rear surface of thecomponent and the structural member of the booster seat towhich they are attached, a clamp such as shown in Fig. 3 may4CAMI Infant Dummy Mark II (shown in Fig. 2) Depart

49、ment of Transportation,Federal Aviation Administration, April 29, 1974, and CAMI Infant Dummy,Drawing No. SA-1001, Memorandum Report AAC-119-74-14, Revision 11, byRichard F. Chandler, July 2, 1994.FIG. 2 CAMI Infant Dummy Mark IIFIG. 3 Tension Test Adapter/ClampF 2640 074be a suitable device.7.1.4.2 Be sure the attachment device does not compress orexpand the component to hinder removal of the component.7.1.4.3 Gradually apply a 15-lbf (67-N) force in the direc-tion that would normally be associated with the removal of thecomponent. Apply the for