ASTM F3010-2013 Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings《弹性地板覆盖物中使用的基于膜形成水分缓解系统的双组分树脂的标准.pdf

1、Designation: F3010 13Standard Practice forTwo-Component Resin Based Membrane-Forming MoistureMitigation Systems for Use Under Resilient FloorCoverings1This standard is issued under the fixed designation F3010; the number immediately following the designation indicates the year oforiginal adoption or

2、, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the properties, application, andperformance of a two-compo

3、nent resin based membrane-forming moisture mitigation system to high moisture concretesubstrates prior to the installation of resilient flooring.1.2 This practice includes recommendations for the prepa-ration of the concrete surface to receive a two-component resinbased membrane-forming moisture mit

4、igation system.1.3 This practice does not supersede written instructions ofthe two-component resin based membrane-forming moisturemitigation system manufacturer, the resilient flooringmanufacturer, underlayment manufacturer, the adhesivemanufacturer, or other components of the finish flooringsystem,

5、 or combinations thereof. Users of this practice shallreview manufacturers technical data sheets and installationinstructions for compatibility of system components.1.4 The following membrane-forming or non membrane-forming moisture mitigation systems are not included in thescope of this practice:1.

6、4.1 Moisture mitigation systems that chemically reactwith any constituent of the concrete to form a gel or crystallinesubstance within the concrete.1.4.2 Penetrating, water- or solvent-based compounds thatdo not form a continuous membrane on the concrete surface.1.4.3 Water-based membrane-forming mo

7、isture mitigationsystems are not included in the scope of this document.1.5 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This stan

8、dard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 A

9、STM Standards:2C109/C109M Test Method for Compressive Strength ofHydraulic Cement Mortars (Using 2-in. or 50-mm CubeSpecimens)C1583 Test Method for Tensile Strength of Concrete Sur-faces and the Bond Strength or Tensile Strength ofConcrete Repair and Overlay Materials by Direct Tension(Pull-off Meth

10、od)D7234 Test Method for Pull-Off Adhesion Strength of Coat-ings on Concrete Using Portable Pull-Off Adhesion Tes-tersE96 Test Methods for Water Vapor Transmission of Materi-alsF141 Terminology Relating to Resilient Floor CoveringsF1869 Test Method for Measuring Moisture Vapor EmissionRate of Concre

11、te Subfloor Using Anhydrous CalciumChlorideF2170 Test Method for Determining Relative Humidity inConcrete Floor Slabs Using in situ ProbesF2420 Test Method for Determining Relative Humidity onthe Surface of Concrete Floor Slabs Using RelativeHumidity Probe Measurement and Insulated Hood2.2 Resilient

12、 Floor Covering Institute (RFCI) Standards:3Recommended Work Practices for the Removal of ResilientFloor Coverings3. Terminology3.1 Definitions:3.1.1 For definitions of terms used in this practice, seeTerminology F141.1This test method is under the jurisdiction ofASTM Committee F06 on ResilientFloor

13、 Coverings and is the direct responsibility of Subcommittee F06.40 onPractices.Current edition approved June 1, 2013. Published July 2013. DOI: 10.1520/F3010-132For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of

14、 ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Resilient Floor Covering Institute, 115 Broad Street, Suite 201,La Grange, GA 30240.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. U

15、nited States14. Significance and Use4.1 Moisture permeating from concrete substrates can det-rimentally affect the performance of resilient floor coveringsystems.All resilient flooring and adhesive manufacturers havea maximum acceptable level of moisture in which theirproducts can perform satisfacto

16、rily. If pre-installation moisturetests indicate that the moisture level is unacceptable for thespecified floor covering to be installed, one option is to applya topical treatment to the concrete substrate surface to mitigatethe moisture condition. Experience has shown that certaintypes of membrane-

17、forming moisture mitigation systems havemore desirable properties and successful performance thanothers. Requirements for membrane-forming moisture mitiga-tion systems to be used, and other related details, are generallyincluded as part of the project plans, or specification details,and may vary fro

18、m the minimum recommendations set forth inthis practice.4.2 This practice is intended for use after it has beendetermined that a floor moisture condition exceeds the resilientfloor covering or adhesive manufacturers requirements, orboth, as tested according to Test Methods F1869, F2170, andF2420.4.3

19、 Membrane-forming moisture mitigation systems are notintended for use over gypsum-based substrates or other mois-ture sensitive substrates.5. Product Requirements5.1 The membrane-forming moisture mitigation systemshall be a two-component resin based product.5.2 Membrane-forming moisture mitigation s

20、ystems to bequalified under this practice shall have a vapor permeance nogreater than 0.1 grains/h/ft2/in. Hg, (perm) when tested inaccordance with Test Method E96 when applied at the recom-mended thickness designated by its manufacturer.5.3 The membrane moisture control systems shall not con-tribut

21、e to unacceptable indentations in some types of resilientflooring under some conditions of use. Refer to membrane-forming moisture mitigation systems manufacturers recom-mendations and floor covering manufacturers specifications.6. Material Acceptance6.1 Membrane-forming moisture mitigation systems

22、shallbe delivered in their original factory packaging.6.2 Membrane-forming moisture mitigation systems shallbe used before any specified expiration date.7. Material Conditioning7.1 The membrane-forming moisture mitigation systemshall be kept in a temperature controlled environment on siteand protect

23、ed from the weather at least 48 h prior to use. Thetemperature shall not be below 65F (18C) or above 85F(29.4C).8. General Guidelines8.1 Concrete substrate surfaces intended to receivemembrane-forming moisture mitigation systems shall be clean,smooth, and structurally sound. They shall be free of du

24、st,solvent, paint, wax, oil, grease, residual adhesive, adhesiveremovers, film-forming curing compounds, silicate penetratingcuring compounds, sealing, hardening, or parting compounds,salts, efflorescence, laitance, mold, mildew, and other foreignmaterials that affect the adhesion of the membrane-fo

25、rmingmoisture mitigation system to concrete.8.2 Consult membrane-forming moisture mitigation systemmanufacturers for appropriate temperature and humidity rangefor the products to be installed and the geographic area wherethe job site is located. Unless instructed otherwise by themembrane-forming moi

26、sture mitigation system manufacturer,the concrete substrate, the installation area and materials shallbe maintained at 65F (18.3C) to 85F (29.4C) and 40 % to60 % relative humidity for 48 h before, during and for 48 hafter completion of the installation. If a system other than thepermanent HVAC sourc

27、e is utilized, it must provide adequatecontrol of both temperature and humidity to recommended orspecific levels for the appropriate time duration.8.3 Membrane-forming moisture mitigation systems mustinclude manufacturers instructions for treatment of isolationand expansion (moving) joints as well a

28、s nonmoving contrac-tion joints and cracks.8.4 Concrete substrates shall be smooth to prevent irregu-larities in the membrane-forming moisture mitigation systemapplication thickness. Roughness or other defects that mayinhibit the ability to achieve the recommended profile shall beground flat prior t

29、o performing recommended surface prepara-tion method as instructed by the membrane-forming moisturemitigation system manufacturer.9. Pre-Installation Testing9.1 Conduct moisture testing of the concrete according toTest Methods F1869, F2170,orF2420 as required by themoisture mitigation system manufac

30、turer. If required, performother types of tests as specified by the flooring manufacturerand the moisture mitigation system manufacturer. Followmoisture mitigation system manufacturers instructions basedon test results where applicable.9.2 Following mechanical preparation of the concretesurface, tes

31、t the tensile strength of the concrete surfaceaccording to Test Method C1583. Tensile strength of theprepared substrate surface must be at least 200 psi, tested inaccordance with Test Method C1583. Areas of insufficientstrength shall be ground to remove the weak material andabrasively prepared again

32、 using appropriately modifiedmethods, and retested for tensile strength.NOTE 1Proper sampling or test intervals and locations shall bedecided in consultation among project stakeholders.9.3 MockupInstall the moisture mitigation system in aminimum 100 ft2mockup area, using the same methods andequipmen

33、t that will be used for the entire installation. Testtensile bond strength of the moisture mitigation system to theconcrete substrate following Test Method D7234. The resultsmust be equal to or greater than 200 psi with failure in theconcrete before proceeding with installation of the moisturemitiga

34、tion system.F3010 13210. Surface Preparation10.1 Most membrane-forming moisture mitigation systemsrequire proper surface preparation in order to ensure maximumperformance and prevent delamination of the concrete surface.Surface preparation to a CSP #3 (Concrete Surface Profile perICRI guidelines) sh

35、all be performed by mechanical meansonly. Acceptable methods include shot blasting, scarifying, orgrinding. Grinding is only acceptable in areas where the shotblast or scarification equipment cannot reach. Grinding entiresubstrate area, acid etching, waterblasting, or sanding, are notacceptable meth

36、ods of concrete surface preparation. Refer tomembrane-forming moisture mitigation system manufacturerif one of the above nonrecommended methods is to be used.NOTE 2Inadequate surface preparation can result in leaving possiblecontaminants that will affect the performance of the membrane-formingmoistu

37、re mitigation systems, resulting in pin holes, bubbles, fish eyes orother deficiencies leading to debonding and coating failure.10.2 Unless instructed otherwise by the membrane-formingmoisture mitigation system manufacturer, allow concrete sub-strate to dry undisturbed for 16 to 24 h following surfa

38、cepreparation process.10.3 Surface depressions or other irregularities shall befilled or smoothed with a patching or leveling material recom-mended by the membrane-forming moisture mitigation systemmanufacturer. Patching material shall be moisture-, mildew-,and alkali-resistant, and shall provide a

39、minimum of 3000 psicompressive strength after 28 days, when tested in accordancewith Test Method C109/C109M.10.4 Surface cracks, grooves, control joints or other non-moving joints shall be filled with a compatible resin basedmaterial recommended by the membrane-forming moisturemitigation system manu

40、facturer for sealing, crack repair, orboth.10.5 Expansion joints, isolation joints, or other movingjoints in the concrete substrate must not be filled or sealed withrigid materials. All moving joints must be honored up throughthe moisture mitigation system, any patching and levelingproducts, and the

41、 resilient floor covering being installed.11. Installation11.1 Follow instructions of the membrane-forming moisturemitigation systems manufacturer. These instructions shall in-clude specific instructions regarding mixing, application, andfilm thickness.11.2 Apply membrane-forming moisture mitigation

42、 systemsto form a continuous monolithic void free application. Refer tomembrane-forming moisture mitigation systems manufacturerregarding treatment of surface deficiencies including but notlimited to pinholes, fish eyes or other surface defects.11.3 If specified in the manufacturers installationinst

43、ructions, provide sand broadcast into top surface of coating.11.4 If a cementitious underlayment is required on top of themembrane-forming moisture mitigation system, install accord-ing to manufacturers instructions. Allow to cure and drybefore proceeding with floor covering installation.11.5 Mainta

44、in environmental conditions required by themembrane-forming moisture mitigation system manufacturerduring the curing period.12. Field Quality Control12.1 Verify that surfaces preparation meets ICRI CSP3 ormanufacturers requirements.12.2 Verify that the membrane-forming moisture mitigationsystem film

45、 thickness meets the manufacturers recommendedthickness.12.3 Verify that the repairs of the membrane-forming mois-ture mitigation system defective area are made according to themanufacturers requirements.13. Protection13.1 Protect the membrane-forming moisture mitigationsystem and the entire subfloo

46、r from traffic, dirt, dust or othercontaminates until final installation of the resilient floor cov-ering.14. Keywords14.1 film thickness; high moisture concrete; moisture miti-gation system; vapor permeanceSUPPLEMENTARY REQUIREMENTSS1. RECOMMENDED WORK PRACTICES FOR REMOVAL OF RESILIENT FLOORCOVERI

47、NGSThe following supplementary requirements shall apply only when specified by the purchaser in thepurchase order or contract.S1.1 Asbestos WarningDo not sand, dry sweep, dry scrape,drill, saw, bead blast, or mechanically chip or pulverizeexisting resilient flooring, backing, lining felt, paint, asp

48、haltic“cutback” adhesives, or other adhesives. These products maycontain asbestos fibers or crystalline silica.Avoid creating dust.Inhalation of such dust is a cancer and respiratory tract hazard.Smoking by individuals exposed to asbestos fibers greatlyincreases the risk of serious bodily harm. Unle

49、ss positivelycertain that the product is a non-asbestos-containing material,you must presume it contains asbestos. Regulations mayrequire that the material be tested to determine asbestoscontent. The Resilient Floor Covering Institute (RFCI)document, “Recommended Work Practices for Removal ofResilient Floor Coverings,” shall be consulted for a defined setF3010 133of instructions addressed to the task of removing all resilientfloor covering structures.S1.2 Lead Paint CautionCertain paints may contain lead.Exposure to excessive amounts of lead dust presents a