ASTM F3103-2014 Standard Specification for Testing Off-Road Motorcycle and ATV Helmets《越野摩托车和亚视头盔试验的标准规格》.pdf

1、Designation: F3103 14Standard Specification forTesting Off-Road Motorcycle and ATV Helmets1This standard is issued under the fixed designation F3103; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb

2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers performance requirements forhelmets used by off-road motorcycle and All-Terrain Vehicle(ATV) riders.1.2 Complianc

3、e with the federally mandated FMVSS No.218 shall be documented as part of compliance with thisASTMstandard.1.3 This specification provides additional performance re-quirements including positional stability and performancecriteria for chin bars on full-facial coverage helmets if thehelmet is equippe

4、d with a chin bar.1.4 This standard does not require that helmets provide fullfacial coverage.1.5 This is a performance specification and is not intendedto restrict design.1.6 All testing and requirements of this specification shallbe in accordance with Test Methods F1446, except where notedherein.1

5、.7 Partial utilization of this standard is prohibited. Anystatement of compliance with this specification must be acertification that the product meets all of the requirements ofthis specification in its entirety. A product that fails to meet anyone of the requirements of this specification is consi

6、dered tohave failed this standard, and should not be sold with anyindication that it meets parts of this standard.1.8 Headgear designed to comply with this and otherstandards may proclaim uses as certified by the manufacturer.1.9 The values stated in SI units are to be regarded asstandard. No other

7、units of measurement are included in thisstandard.1.10 The following safety caveat applies to the chemical,mechanical, or physical, or a combination thereof, test methodsdescribed herein and is meant specifically for those performingthe tests (in an effort to provide them with notice to take theappr

8、opriate precautions when conducting the tests): This stan-dard does not purport to address all of the safety concerns, ifany, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulator

9、y limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2F1446 Test Methods for Equipment and Procedures Used inEvaluating the Performance Characteristics of ProtectiveHeadgearF2220 Specification for HeadformsF2727 Guide for Manufacturers for Labeling HeadgearProducts2.2 Other Standard

10、s:UNI EN 960 Headforms for Use in the Testing of ProtectiveHelmetsFederal Motor Vehicle Safety Standard No. 218 MotorcycleHelmets, effective May 13, 2013Laboratory Test Procedure for FMVSS No. 218: TP-218-07 effective May 13, 2013American National Standard for Four Wheel All-TerrainVehicles, ANSI SV

11、IA 1-20103. Terminology3.1 DefinitionsOff-road motorcycle and ATV useincludes, but is not limited to, motocross, supercross, enduro,endurocross, arenacross, flat-track, observed trials, hill-climbing, ice-racing, and non-competitive uses such as trail,cross-country, desert, sand dune riding, etc.3.2

12、 All-Terrain Vehicle (ATV), na motorized off-highwayvehicle designed to travel on four low pressure tires, having aseat designed to be straddled by the operator and handlebars forsteering control (ANSI SVIA 1-2010, section 3).3.3 This standard is not applicable to off-road vehicles inwhich the opera

13、tor or passenger are enclosed and/or restrainedwith a lap/shoulder belt system.1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.53 on Headgear and Helmets.Current edition appro

14、ved Sept. 1, 2014. Published September 2014. DOI:10.1520/F3103-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM web

15、site.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14. Labels and Warnings4.1 Shall meet the requirements set forth in Test MethodsF1446.4.2 Shall follow the guidelines set forth in Guide F2727.4.3 Shall have the words “For off-road

16、motorcycle and ATVriding and racing.”4.4 Shall comply with all labeling requirements of FMVSS218 at S5.6.5. Marking the Test Line5.1 The test line is shown in Fig. 1 and shall be marked inaccordance with Test Methods F1446. The test area created bythis test line must fall completely on the helmet.HE

17、ADFORM DIMENSIONSIZE X L/2 Y R S T UA 24.0 88.0 89.7 47.5 23.0 142.0 84.0E 26.0 94.5 96.0 49.0 24.0 151.0 88.0J 27.5 101.0 102.5 50.5 25.0 160.0 92.0M 29.0 106.0 107.0 52.0 27.0 166.0 96.0O 30.0 108.5 110.0 53.0 27.0 170.0 97.0FIG. 1 Marking the Test LineF3103 1426. Conditioning and Number of Sample

18、s6.1 Conditioning of the samples to be tested shall be inaccordance with the section entitled “Conditioning Environ-ments” in Test Methods F1446. All tests for compliance withthis standard are done in ambient condition.6.2 For all helmets with or without a chin bar, one samplehelmet is required for

19、each shell-liner size combination asdefined in Test Methods F1446.7. Impact Sites7.1 There are currently no impact tests specified beyondthose included in compliance with FMVSS 218 at 10.1.8. Roll-Off Testing8.1 The ambient helmet shall be subjected to the Roll-Offtest in accordance with Test Method

20、s F1446 subsection 12.7.2using a 10-kg drop mass from a height of 0.6 m and utilizingthe failure criteria established by F1446.9. Chin Bar Rigidity Test9.1 The chin bar rigidity test applies to helmets with a chinbar only.9.2 If a chin bar is present, it shall be tested in accordancewith the procedu

21、res in Test Methods F1446, Chin Bar RigidityTest, subsection 12.9, with an impact velocity of 3.5 m/s+5%,using an ambient sample that has not been subjected to anyother impact testing.9.3 The maximum deflection of the chin bar shall notexceed 60 mm as specified by Test Methods F1446 subsection12.9.1

22、.10. Compliance Documentation10.1 Compliance with this standard requires documentedcompliance with FMVSS No. 218: Motorcycle Helmets. Eachcompliance test report to this ASTM standard must have acomplete and passing test report showing compliance withFMVSS 218. For a sample report, refer to the curre

23、nt FMVSS218 Test Procedure (TP-218-07). This supporting documentshall be attached to the ASTM XXXX report. Without asupporting FMVSS 218 report, the ASTM report will be inviolation of subsection 1.8 prohibiting partial compliance.11. Keywords11.1 all-terrain vehicle; ATV; competition; headgear; hel-

24、met; motocross; motorcycle; off-road; racing; sand dune; trailASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such

25、patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited

26、either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fa

27、ir hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this st

28、andard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 143