1、Designation: F3141 17F3141 17aStandard Guide forTotal Knee Replacement Loading Profiles1This standard is issued under the fixed designation F3141; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number
2、in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 Motion path, load history and loading modalities all contribute to the wear, degradation and damage of implantedprosthetics. Simulating a vari
3、ety of functional activities promises more realistic testing for wear and damage mode evaluation.Such activities are often called activities of daily living (ADLs). ADLs identified in the literature include walking, stair ascent anddecent, sit-to-stand, stand-to-sit, squatting, kneeling, cross-legge
4、d sitting, into bath, out of bath, turning and cutting motions (1-7).2Activities other than walking gait often involve an extended range of motion and higher imposed loading conditions which havethe ability to cause damage and modes of failure other than normal wear (8-10).1.2 This document provides
5、 guidance for functional simulation that could be used to evaluate in vitro the durability of kneeprosthetic devices under force control.1.3 Function simulation is defined as the reproduction of loads and motions that might be encountered in activities of dailyliving but it does not necessarily cove
6、r every possible type of loading. Functional simulation differs from typical wear testing inthat it attempts to exercise the prosthetic device through a variety of loading and motion conditions such as might be encounteredin situ in the human body in order to reveal various damage modes and damage m
7、echanisms that might be encountered throughoutthe life of the prosthetic device.1.4 Force control is defined as the mode of control of the test machine that accepts a force level as the set point input and whichutilizes a force feedback signal in a control loop to achieve that set point input. For k
8、nee simulation, the flexion motion is placedunder angular displacement control, internal and external rotation is placed under torque control, and axial load, anterior posteriorshear and medial lateral shear are placed under force control.1.5 This document establishes kinetic and kinematic test cond
9、itions for several activities of daily living, including walking,turning navigational movements, stair climbing, stair descent, and squatting. The kinetic and kinematic test conditions areexpressed as reference waveforms used to drive the relevant simulator machine actuators. These waveforms represe
10、nt motion, asin the case of flexion extension, or kinetic signals representing the forces and moments resulting from body dynamics, gravitationand the active musculature acting across the knee.1.6 This document does not address the assessment or measurement of damage modes, or wear or failure of the
11、 prostheticdevice.1.7 This document is a guide. As defined by ASTM in their “Form and Style for ASTM Standards” book in section C15.2, “Astandard guide is a compendium of information or series of options that does not recommend a specific course of action. Guidesare intended to increase the awarenes
12、s of information and approaches in a given subject area. Guides may propose a series ofoptions or instructions that offer direction without recommending a definite course of action. The purpose of this type of standardis to offer guidance based on a consensus of viewpoints but not to establish a sta
13、ndard practice to follow in all cases.” The intentof this guide is to provide loading profiles and test procedures to develop testing that might be used for wear, durability or othertypes of testing of total knee replacements. As noted in this definition, a guide provides guidance on testing, but do
14、es not requirespecific testing. Thus, for example, if a user is unable to control one mode of force control given in the load profiles, that user isnot required to perform that mode of loading.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use.
15、It is the responsibilityof the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use.1 This guide is under the jurisdiction of ASTM Committee F04 on Medical and Surgical Materials
16、and Devices and is the direct responsibility of Subcommittee F04.22on Arthroplasty.Current edition approved June 1, 2017Dec. 1, 2017. Published July 2017January 2018. Originally approved in 2015. Last previous edition approved in 20152017 asF314115.17. DOI: 10.1520/F3141-17.10.1520/F3141-17A.2 The b
17、oldface numbers in parentheses refer to the list of references at the end of this standard.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possibl
18、e to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West
19、Conshohocken, PA 19428-2959. United States11.9 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World
20、Trade Organization Technical Barriers to Trade (TBT) Committee.2. Reference Frame System (see Fig. 1)2.1 Two right-handed coordinate systems are defined as reference frames; one with an origin at OT fixed to the tibia and a secondwith an origin at OF fixed to the femur.2.2 Displacements (rotations a
21、nd translations) shall mean displacements of the tibial component relative to the femoralcomponent. The anatomical axes correspond to the mechanical axes described by Grood and Suntay (11).Table 1 shows themechanical axes and abbreviations corresponding to each anatomical axis.2.3 The orientation an
22、d location of the axes of the reference frames follow the approach defined by Pennock (12). However,to accommodate the simulator machine (versus anatomical) setting several modifications are made to the Pennock approach, asdescribed in 2.4.2.4 The femoral reference frame defines three coordinate axe
23、s, XF, YF, and ZF all coincident at the origin OF. The flexion axis,XF, shall be defined as collinear with a line passing through the coordinates of the average center of curvature of the posterior 90degrees of condylar arc. The average center of curvature shall be developed individually for the med
24、ial and lateral condyles basedon regular increments of angle from 0 to 90 degrees of posterior arc (the transepicondylar line may be substituted for the averagecenter of curvature if the manufacturer specifies that reference frame for surgical alignment purposes). The long axis of the femur,ZF, lies
25、 on a line passing through the center of the femoral head which extends to the medial lateral midpoint of the trans-condylarline, lying on the XF axis, connecting the most medial and most lateral points of the medial and lateral femoral condyles at theirmost distal projection. The ZF axis shall be p
26、erpendicular to the XF axis and the YF axis shall be defined as the cross product ofthe ZF and XF axes.Two righted-handed reference frames, OF and OT, are embedded in and move with the femur and tibia respectively. The coordinate system and signs are based on aright knee and forces and moments are c
27、onsidered to be applied to the tibia shaft with reaction forces acting at the joint articular surface.FIG. 1 Reference Frame SystemF3141 17a22.5 The tibial reference frame defines three coordinate axes, XT, YT, and ZT, all coincident at the origin OT. The anatomicallong axis of the tibia, ZT, is def
28、ined by a line extending from the center of the tibial intercondylar eminence to the center of theankle (12). This definition shall be adopted for this standard. The XT, YT, axis shall be defined with the knee in full extension andin a neutral configuration. In that configuration the XT axis shall b
29、e parallel to the femoral XF axis and the YT axis will be coplanarwith the plane of the YF and ZF axes. The XT and YT axes will be mutually perpendicular to the ZT axis. The origin OT of thetibial coordinate system shall be located such that the XT axis is tangent to the most distal aspect of the ti
30、bial articular bearingsurface.2.6 Grood and Suntay describe the motions of the knee using the notion of a mechanical linkage that constrains rotation andtranslation axes in a way that is thought to be clinically relevant. To define this motion a floating axis, YF is utilized. This axisis labeled the
31、 abduction axis. The abduction axis remains perpendicular to both the XF axis and the ZT axis in all configurations.The abduction axis is rotated about the XF axis by an arc equal to flexion-extension arc.3. Terminology3.1 Definitions:3.1.1 activity model, nan activity model provides a kinematic and
32、 kinetic description of a particular physiological activity.Each activity model shall provide a set of time series data that represents one cycle of the subject activity. The time series dataprovided by an activity model are used as inputs to control the motions and forces of the test machine. The t
33、ime series data requiredto characterize each activity are: (1) axial force, (2) flexion-extension angle, (3) axial tibial torque, (4) anterior-posterior force, and(5) medial-lateral force. These torques or forces may result in the motion of the femur or tibial relative to the other. How thesemotions
34、 are described may be machine-dependent, as to whether it is a motion of the tibia relative to the femur or the femur relativeto the tibia. The following descriptions are frequently described as motion of the tibia, but could also be described as motion ofthe femur.3.1.2 activities of daily living,
35、ADLs, nthese are the physiological activities to which a human knee may be subject during thecourse of normal living. Typical ADLs include: high frequency maneuvers such as walking and turning; navigational maneuverssuch as cross over turning and pivot turning; deep knee flexion maneuvers such as sq
36、uatting, stair ascent and descent; high loadingmaneuvers such as stumbling; and athletic activities.3.1.3 AP translation, dTap or dTy mm, ntranslation of the tibial component along the YT axis (anterior posterior axis); apositive displacement moves the tibia in the anterior direction. The magnitude
37、of the displacement is expressed relative to thereference position.3.1.4 AP force, f Tap or f Ty N, napplied anterior or posterior force acting on the tibial component parallel to the YT axis. Apositive AP force acts in the positive YT direction and will result in an anterior translation of the tibi
38、a.3.1.5 applied force, napplied force is that force acting on the joint originating from external sources (includes themusculature). When magnitude and direction are specified the applied force shall be considered to be acting on the tibial shaft withbalancing reaction forces at the joint surface.3.
39、1.5.1 DiscussionThe forces acting across the knee are partitioned into applied and constraint forces while the constraint forces are furtherpartitioned into joint reaction force and soft tissue constraint force. The applied force is comprised of the sum of the influencesof gravitation, body dynamics
40、, and the action of the active musculature. The joint reaction force is comprised of the influence ofall of the mechanisms which contribute to the forces of contact acting on the articular joint surface. The soft tissue constraint forceis comprised of the sum of all of the influences of the passive
41、soft tissue structure which is dominated by the elastic and viscoelasticresponse of the ligaments and capsular structure surrounding the joint.3.1.6 joint coordinate system, JCS, nthe coordinate system and kinematic chain described by Grood and Suntay to representthe translational and rotational axe
42、s and motions of the knee.3.1.7 neutral position, nthis is the position where the forces (or torques) are zero and corresponds to zero on the force (ortorque) deflection graphs defining the constraint forces and torques.TABLE 1 Anatomical Meaning of Coordinate System Axes andAbbreviationsAnatomical
43、Axis Coordinate Axis AbbreviationsMedial Lateral XF MLAnterior Posterior YT APAxial ZT AXFlexion Extension XF FEInternal External Rotation ZT IEAbduction Adduction YF AAF3141 17a33.1.8 reference orientation, nthe reference orientation is the relative alignment of the tibial and femoral components de
44、finedby the manufacturer as the desirable alignment at full extension and neutral IE rotation.3.1.9 reference position, nthe reference position is determined with the prosthetic components aligned in the referenceorientation. The reference position is that position on theAPand MLaxis where an axial
45、load results in noAPor MLreaction force.This may be determined experimentally in the test machine by applying 100 N of axial load and then exercising the machinethrough a range of AP or ML motion while recording the corresponding AP or ML reaction force and displacement. The midpointof the minimum c
46、usp of the force displacement curve is the reference position.3.1.9.1 DiscussionThe reference position may be determined analytically or graphically as that point where, when in the reference orientation, thesurface normal of contact points of the femoral and tibial components are collinear with the
47、 axial load axis.4. Significance and Use4.1 The purpose of this test guide is to provide load profile information on how one could test a total knee replacement in orderto evaluate in vitro its function and wear during several types of knee motions as described in 4.2 and 4.3.4.2 This test guide may
48、 help characterize the magnitude and location of implant wear as an implant is repetitively movedaccording to specified load and displacement waveforms.4.3 This test guide may also help characterize the functional limitations of a total knee replacement as its motion is guided bythese waveforms. The
49、se limitations may be observed as impingement, subluxation or high loading in the soft tissue constraints,whether they are represented physically or virtually.4.4 The motions and load conditions in vivo will, in general, differ from the load and motions defined in this guide. The resultsobtained from this guide cannot be used to directly predict in vivo performance. However, this guide is designed to allow forcomparisons in performance of different knee designs, when tested under similar conditions.5. Apparatus5.1 A joint motion simulator machine is requ
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1