ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:231.26KB ,
资源ID:540759      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-540759.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM G96-1990(2018) Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)《在线监测工厂设备腐蚀性的标准指南(电气和电化学方法)》.pdf)为本站会员(jobexamine331)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM G96-1990(2018) Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)《在线监测工厂设备腐蚀性的标准指南(电气和电化学方法)》.pdf

1、Designation: G96 90 (Reapproved 2018)Standard Guide forOnline Monitoring of Corrosion in Plant Equipment(Electrical and Electrochemical Methods)1This standard is issued under the fixed designation G96; the number immediately following the designation indicates the year of originaladoption or, in the

2、 case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide covers the procedure for conducting onlinecorrosion monitoring of metals in plan

3、t equipment underoperating conditions by the use of electrical or electrochemicalmethods. Within the limitations described, these test methodscan be used to determine cumulative metal loss or instanta-neous corrosion rate, intermittently or on a continuous basis,without removal of the monitoring pro

4、bes from the plant.1.2 The following test methods are included: Test MethodAfor electrical resistance, and Test Method B for polarizationresistance.1.2.1 Test Method A provides information on cumulativemetal loss, and corrosion rate is inferred. This test methodresponds to the remaining metal thickn

5、ess except as describedin Section 5.1.2.2 Test Method B is based on electrochemical measure-ments for determination of instantaneous corrosion rate butmay require calibration with other techniques to obtain truecorrosion rates. Its primary value is the rapid detection ofchanges in the corrosion rate

6、 that may be indicative ofundesirable changes in the process environment.1.3 The values stated in SI units are to be consideredstandard. The values in parentheses are for information only.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is

7、theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Specific precautionary statements are given in 5.6.1.5 This international standard was developed in accor-dance

8、 with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Stand

9、ards:2D1125 Test Methods for Electrical Conductivity and Resis-tivity of WaterG1 Practice for Preparing, Cleaning, and Evaluating Corro-sion Test SpecimensG3 Practice for Conventions Applicable to ElectrochemicalMeasurements in Corrosion TestingG4 Guide for Conducting Corrosion Tests in Field Applic

10、a-tionsG15 Terminology Relating to Corrosion and Corrosion Test-ing (Withdrawn 2010)3G59 Test Method for Conducting Potentiodynamic Polariza-tion Resistance MeasurementsG102 Practice for Calculation of Corrosion Rates and Re-lated Information from Electrochemical Measurements3. Terminology3.1 Defini

11、tionsSee Terminology G15 for definitions ofterms used in this guide.4. Summary of Guide4.1 Test Method AElectrical ResistanceThe electricalresistance test method operates on the principle that theelectrical resistance of a measuring element (wire, strip, or tubeof metal) increases as its cross-secti

12、onal area decreases:R 5 lA(1)where:R = resistance, = resistivity of metal (temperature dependent),l = length, andA = cross-section area.In practice, the resistance ratio between the measuringelement exposed to corrosion and the resistance of a similar1This guide is under the jurisdiction of ASTM Com

13、mittee G01 on Corrosion ofMetals and is the direct responsibility of ASTM Subcommittee G01.11 onElectrochemical Measurements in Corrosion Testing.Current edition approved May 1, 2018. Published June 2018. Originallyapproved in 1990. Last previous edition approved in 2013 as G96 90 (2013). DOI:10.152

14、0/G0096-90R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical s

15、tandard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on P

16、rinciples for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1reference element protected from corrosion is measured, tocompensate for resistivity changes due to temperature. Basedon the initial

17、 cross-sectional area of the measurement element,the cumulative metal loss at the time of reading is determined.Metal loss measurements are taken periodically and manuallyor automatically recorded against a time base. The slope of thecurve of metal loss against time at any point is the correctionrat

18、e at that point. The more frequently measurements are taken,the better is the resolution of the curve from which thecorrosion rate is derived.4.1.1 The electrical resistance of the metal elements beingmeasured is very low (typically 2 to 10 m). Consequently,special measurement techniques and cables

19、are required tominimize the effect of cable resistance and electrical noise.4.1.2 Various probe element cross-sectional areas are nec-essary so that a wide range of corrosion rates can be monitoredwith acceptable resolution.4.2 Test Method BPolarization Resistance:4.2.1 The polarization resistance t

20、est method involves inter-action with the electrochemical corrosion mechanism of metalsin electrolytes in order to measure the instantaneous corrosionrate. Its particular advantage is its speed of response tocorrosion rate upsets. On a corroding electrode subject tocertain qualifications (see 12.1),

21、 it has been shown that thecurrent density associated with a small polarization of theelectrode is directly proportional to the corrosion rate of theelectrode.4.2.2 The polarization resistance equation is derived in TestMethod G59. See Practice G3 for applicable conventions. Forsmall polarization of

22、 the electrode (typically E up to 20 mV),the corrosion current density is defined as:icorr5BRp(2)where:B = a combination of the anodic and cathodic Tafel slopes(ba,bc), andRp= the polarization resistance with dimensions ohmcm2.B 5babc2.303 ba1bc!(3)4.2.3 The corrosion current density, icorr, can be

23、convertedto corrosion rate of the electrode by Faradays law if theequivalent weight (EW) and density, , of the corroding metalare known (see Practice G102):corrosion rate 5 K1icorrEW (4)where:K1= a constant.4.2.4 Equivalent weight of an element is the molecularweight divided by the valency of the re

24、action (that is, thenumber of electrons involved in the electrochemical reaction).4.2.5 In order to obtain an alloy equivalent weight that is inproportion with the mass fraction of the elements present andtheir valence, it must be assumed that the oxidation process isuniform and does not occur selec

25、tively; that is, each element ofthe alloy corrodes as it would if it were the only elementpresent. In some situations these assumptions are not valid.4.2.6 Effective equivalent weight of an alloy is as follows:1(lmnifiWi(5)where:fi= mass fraction of ithelement in the alloy,Wi= atomic weight of the i

26、thelement in the alloy,ni= exhibited valence of the ithelement under the condi-tions of the corrosion process, andm = number of component elements in the alloy (normallyonly elements above 1 mass % in the alloy areconsidered).Alloy equivalent weights have been calculated for manyengineering metals a

27、nd alloys and are tabulated in PracticeG102.4.2.7 Fig. 1 represents an equivalent circuit of polarizationresistance probe electrodes in a corroding environment. Thevalue of the double layer capacitance, Cdl, determines thecharging time before the current density reaches a constantvalue, i, when a sm

28、all potential is applied between the test andauxiliary electrode. In practice, this can vary from a fewNOTE 1Rs= Solution Resistance (ohmcm2) between test and auxiliary electrodes (increases with electrode spacing and solution resistivity).Ru= Uncompensated component of solution resistance (between

29、test and reference electrodes) (ohmcm2).Rp= Polarization Resistance Rp(ohmcm2).Cdl= Double layer capacitance of liquid/metal interface.i = Corrosion current density.FIG. 1 Equivalent Circuit of Polarization Resistance ProbeG96 90 (2018)2seconds up to hours. When determining the polarizationresistanc

30、e, Rp, correction or compensation for solutionresistance, Rs, is important when Rsbecomes significantcompared to Rp. Test Methods D1125 describes test methodsfor electrical conductivity and resistivity of water.4.2.8 Two-electrode probes, and three-electrode probes withthe reference electrode equidi

31、stant from the test and auxiliaryelectrode, do not correct for effects of solution resistance,without special electronic solution resistance compensation.With high to moderate conductivity environments, this effect ofsolution resistance is not normally significant (see Fig. 2).4.2.9 Three-electrode

32、probes compensate for the solutionresistance, Rs, by varying degrees depending on the positionand proximity of the reference electrode to the test electrode.With a close-spaced reference electrode, the effects of Rscan bereduced up to approximately ten fold. This extends the oper-ating range over wh

33、ich adequate determination of the polar-ization resistance can be made (see Fig. 2).4.2.10 A two-electrode probe with electrochemical imped-ance measurement technique at high frequency short circuitsthe double layer capacitance, Cdl, so that a measurement ofsolution resistance, Rs, can be made for a

34、pplication as acorrection. This also extends the operating range over whichadequate determination of polarization resistance can be made(see Fig. 2).4.2.11 Even with solution resistance compensation, there isa practical limit to the correction (see Fig. 2). At highersolution resistivities the polari

35、zation resistance technique can-not be used, but the electrical resistance technique may beused.NOTE 1See Appendix X1 for derivation of curves and Table X1.1 for description of points A, B, C and D.NOTE 2Operating limits are based on 20 % error in measurement of polarization resistance equivalent ci

36、rcuit (see Fig. 1).NOTE 3In the Stern-Geary equations, an empirical value of B = 27.5 mV has been used on the ordinate axis of the graph for “typical corrosion rateof carbon steel”.NOTE 4Conductivitymhos!cm51 000000Resistivity ohmcm!NOTE 5Effects of solution resistance are based on a probe geometry

37、with cylindrical test and auxiliary electrodes of 4.75 mm (0.187 in.) diameter,31.7 mm (1.25 ft) long with their axes spaced 9.53 mm (0.375 in.) apart. Empirical data shows that solution resistance (ohmscm2) for thisgeometry = 0.55 resistivity (ohmscm2).NOTE 6A two-electrode probe, or three-electrod

38、e probe with the reference electrode equidistant from the test and auxiliary electrode, includes % ofsolution resistance between working and auxiliary electrodes in its measurement of Rp.NOTE 7A close-space reference electrode on a three electrode probe is assumed to be one that measures 5 % of solu

39、tion resistance.NOTE 8In the method for Curve 1, basic polarization resistance measurement determines 2Rp+ Rs(see Fig. 1). High frequency measurement shortcircuits Cdlto measure Rs. By subtraction polarization resistance, Rpis determined. The curve is based on high frequency measurement at 834 Hz wi

40、thCdlof 40 F/cm2on above electrodes and 6 1.5 % accuracy of each of the two measurements.NOTE 9Curve 1 is limited at high conductivity to approximately 700 mpy by error due to impedance of Cdlat frequency 834 Hz.At low conductivityit is limited by the error in subtraction of two measurements where d

41、ifference is small and the measurements large.NOTE 10Errors increase rapidly beyond the 20 % error line (see Appendix X1, Table X1.1).FIG. 2 Guidelines on Operating Range for Polarization ResistanceG96 90 (2018)34.2.12 Other methods of compensating for the effects ofsolution resistance, such as curr

42、ent interruption, electrochemi-cal impedance and positive feedback have so far generally beenconfined to controlled laboratory tests.5. Significance and Use5.1 General corrosion is characterized by areas of greater orlesser attack, throughout the plant, at a particular location, oreven on a particul

43、ar probe. Therefore, the estimation ofcorrosion rate as with mass loss coupons involves an averagingacross the surface of the probe. Allowance must be made forthe fact that areas of greater or lesser penetration usually existon the surface. Visual inspection of the probe element, coupon,or electrode

44、 is required to determine the degree of interferencein the measurement caused by such variability. This variabilityis less critical where relative changes in corrosion rate are to bedetected.5.2 Both electrical test methods described in this guideprovide a technique for determining corrosion rates w

45、ithout theneed to physically enter the system to withdraw coupons asrequired by the methods described in Guide G4.5.3 Test Method B has the additional advantage of provid-ing corrosion rate measurement within minutes.5.4 These techniques are useful in systems where processupsets or other problems ca

46、n create corrosive conditions. Anearly warning of corrosive attack can permit remedial actionbefore significant damage occurs to process equipment.5.5 These techniques are also useful where inhibitor addi-tions are used to control the corrosion of equipment. Theindication of an increasing corrosion

47、rate can be used to signalthe need for additional inhibitor.5.6 Control of corrosion in process equipment requires aknowledge of the rate of attack on an ongoing basis. These testmethods can be used to provide such information in digitalformat easily transferred to computers for analysis.TEST METHOD

48、 AELECTRICAL RESISTANCE(1-6)46. Limitations and Interferences6.1 Results are representative for average metal loss on theprobe element. On wire-form measuring elements, pitting maybe indicated by rapid increases in metal loss reading after 50 %of probe life is passed. The larger cylindrical measurin

49、gelements are much less sensitive to the effect of pitting attack.Where pitting is the only form of attack, probes may yieldunreliable results.6.2 It should be recognized that the thermal noise andstress-induced noise on probe elements, and electrical noise onthese systems, occur in varying degrees due to the process andlocal environment. Care should be exercised in the choice ofthe system to minimize these effects. Electrical noise can beminimized by use of correct cabling, and careful location ofequipment and cable runs (where applicable)

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1