AWWA C220-2017 Stainless-Steel Pipe 1 2 In (13 mm) and Larger.pdf

1、AWWA Standard SM Stainless-Steel Pipe, 1/2 In. (13 mm) and Larger Effective date: Nov. 1, 2017. First edition approved by AWWA Board of Directors June 18, 1992. This edition approved June 11, 2017. Approved by American National Standards Institute May 20, 2017. ANSI/AWWA C220-17 (Revision of ANSI/AW

2、WA C220-12) Copyright 2017 American Water Works Association. All Rights Reserved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrativ

3、e information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA pub- lication of a standard does not constitute e

4、ndorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or code of any governmental authority. AWWA standards

5、are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal American Water Works Assoc

6、iation. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and prov

7、isions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing, pur

8、chasing, or using products, processes, or proce- dures not conforming to the standard. American National Standards are subject to periodic review, and users are cau- tioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state

9、 on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front cover of this standard indi

10、cates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National S

11、tandards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. hours of work by your fellow water professionals. Revenue from the sales of this A

12、WWA material supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of ISBN-13, print: 978-1-62576-266-5 eISBN-13, electronic: 978-1-61300-45

13、0-0 DOI:http:/dx.doi.org/10.12999/AWWA.C220.17 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quot

14、ations for review purposes, without the written permission of the publisher. Copyright 2017 by American Water Works Association Printed in USA Copyright 2017 American Water Works Association. All Rights Reserved. iii Committee Personnel The Steel Water Pipe Manufacturers Technical Advisory Committee

15、 (SWPMTAC) Task Group on updating AWWA C220 had the following personnel at the time: Brandon Dix, Chair E. Bird, Smith-Blair Inc., Texarkana, Texas (AWWA) T. Crail, Straub Coupling, Bonsall, Calif. (AWWA) B. Dix, Felker Brothers, Marshfield, Wis. (AWWA) J. Grocki, Swepco, Enfield, Conn. (AWWA) M. La

16、ngenhan, Total Piping Solutions Inc., Olean, N.Y. (AWWA) A. Lemke, Romac Industries Inc., Bothell, Wash. (AWWA) D. Piontek, Total Piping Solutions Inc., Olean, N.Y. (AWWA) D. Seals, JCM Industries, Nash, Texas (AWWA) N. Thogersen, Romac Industries Inc., Bothell, Wash. (AWWA) M.A. Vanderbosch, CAB In

17、c., Oakwood, Ga. (AWWA) M. Zimmerle, Cascade Waterworks Mfg. Co., Yorkville, Ill. (AWWA) The AWWA Standards Committee on Stainless Steel Pipe, which reviewed and approved this standard, had the following personnel at the time of approval: J. Warren Green, Chair Mike Quinnell, Secretary General Inter

18、est Members R.J. Card,* Lockwood, Andrews (2) external pressure; (3) special physical loading, such as continuous-beam loading with saddle supports or ring girders, vacuum conditions, type of joint used, and variations in operating temperature; and (4) practical considerations for handling, shipping

19、, or similar operations. * Both publications available from National Academy of Sciences, 500 Fifth Street, NW, Washington, DC 20418. Copyright 2017 American Water Works Association. All Rights Reserved. ix The design techniques described in AWWA Manual M11, Steel PipeA Guide for Design and Installa

20、tion, are used to determine the minimum wall thicknesses of steel pipe. Pipe-wall thickness to meet the design requirements will be determined by the appropriate formulas in AWWA Manual M11 using stainless-steel material properties. The purchaser shall establish and specify the minimum wall thicknes

21、s determined to be satisfactory for the service conditions of the pipe. Alternatively, the purchaser may provide the performance criteria for the pipeline and request the manufacturer to design the pipe for purchaser acceptance. The purchaser should consider the proper - ties of the lining and coati

22、ng materials, if specified, when selecting design stresses and deflection limits. The manufacturer may select materials and manufacturing processes within the limitations of this standard to produce pipe of the minimum wall thickness as specified or approved by the purchaser. II.A.1 Application. The

23、 provisions of this standard cover the requirements for stainless-steel pipe for use in water treatment plants, water transmission and distribution systems, and other water facilities. The purchaser is responsible for determining whether any unusual circumstances related to the project require addit

24、ional provisions that are not included in the standard. Such special conditions might affect design, manufacture, quality control, corrosion protection, or handling requirements. II.A.2 Testing of Special Sections. Sec. 5.2.2.1 describes nondestructive testing methods for weld seams of special secti

25、ons that may be necessary by request of the purchaser. The requirement for this special testing should be specified at the time of purchase. II.A.3 Roundness of Pipe. The roundness of pipe during handling, shipping, joint makeup, and backfilling should be specified by the purchaser. Pipe may have to

26、 be stulled to remain round. III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A. Purchaser Options and Alternatives. The following inf

27、ormation should be provided by the purchaser: 1. Standard usedthat is, AWWA C220, Stainless-Steel Pipe, 1/2 in. (13 mm) and Larger, of latest revision. 2. Whether compliance with NSF/ANSI 61, Drinking Water System ComponentsHealth Effects, is required. 3. A description and/or drawings detailing the total quantity of pipe required for each diameter. Copyright 2017 American Water Works Association. All Rights Reserved.