AWWA C221-2012 Fabricated Steel Mechanical Slip-Type Expansion Joints.pdf

1、 ANSI/AWWA C221-12 (Revision of ANSI/AWWA C221-07) AWWA Standard Effective date: Dec. 1, 2012. First edition approved by AWWA Board of Directors Feb. 2, 1997. This edition approved June 10, 2012. Approved by American National Standards Institute Sept. 5, 2012. 6666 West Quincy Avenue Advocacy Denver

2、, CO 80235-3098 Communications T 800.926.7337 Conferences www.awwa.org Education and TrainingScience and TechnologySections The Authoritative Resource on Safe WaterFabricated Steel Mechanical Slip-Type Expansion Joints SM Copyright 2012 American Water Works Association. All Rights Reserved. ii AWWA

3、Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contained in specifi- cations. The AWWA standards usually contain o

4、ptions that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA publication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any pro

5、duct. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or codes of any governmental authority. AWWA standards are intended to represent a consensus of the water supply industry that the product descr

6、ibed will provide satisfactory service. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal - American Water Works Association. The action becomes effective on the first day of the month following the m

7、onth of Journal - American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufact

8、urer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the stand

9、ard. Ameri- can National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags o

10、r labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may

11、 be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of ANSI approval. Purchasers of American National Standards may receive current information on all standards by calling or writ- in

12、g the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; (212) 642-4900, or emailing infoansi.org. ISBN-13, print: 978-1-58321-903-4 eISBN-13, electronic: 978-1-61300-198-1 ISBN-10, print: 1-58321-903-X eISBN-10, electronic: 1-61300-198-3 All rights reserve

13、d. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quotations for review purposes, without the written permission of the

14、 publisher. Copyright 2012 by American Water Works Association Printed in USA Copyright 2012 American Water Works Association. All Rights Reserved. iii Committee Personnel The Steel Water Pipe-Manufacturers Technical Advisory Committee (SWMPTAC) Task Group for AWWA C221, which reviewed and revised t

15、his standard, had the following personnel at the time: Ram N. Satyarthi, Chair Chris Shelley, Vice-Chair E. Bird, Smith-Blair Inc., Texarkana, Texas (AWWA) S. Bradberry, Ford Meter Box Company, Pell City, Ala. (AWWA) R.J. Card, Manufacturing Consultant, Houston, Texas (AWWA) A. Collins, JCM Industri

16、es, Nash, Texas (AWWA) T.C. Crail, Straub Coupling, Bonsall, Calif. (AWWA) J. Grocki, Splash, Enfield, Conn. (AWWA) S. Lamb, Nickel Institute, Huntington, W. Va. (AWWA) D. Pointek, Total Piping Solutions Inc., Olean, N.Y. (AWWA) R.N. Satyarthi, Baker Coupling Company Inc., Los Angeles, Calif. (AWWA)

17、 C. Shelley, Victaulic Depend-O-Lok Inc., Atlanta, Ga. (AWWA) A. Steffan, Dresser Inc., Bradford, Pa. (AWWA) G. Tate, Viking Johnson, Hitchen, UK (AWWA) N. Thogersen, Romac Industries Inc., Bothell, Wash. (AWWA) The AWWA Standards Committee on Steel Pipe, which reviewed and approved this standard, h

18、ad the following personnel at the time of approval: John H. Bambei Jr., Chair Dennis Dechant, Vice-Chair John L. Luka, Secretary General Interest Members W.R. Brunzell, Brunzell Associates Ltd., Skokie, Ill. (AWWA) R.J. Card, Lockwood, Andrews or specification, tolerance, and preparation of pipe end

19、s (Sec. 4.2.3.2). 18. Shop and optional coatings (Sec. 4.4). 19. Material certifications (Sec. 5.1.1.2). 20. Purchasers inspection requirements (Sec. 5.1.2). 21. Purchaser shall specify if a certified welding inspector (CWI) is required (Sec. 5.2). 22. Purchasers proof test requirements (Sec. 5.3.1)

20、. 23. Hydrostatic test requirements (Sec. 5.3.2.2). 24. Additional nondestructive weld evaluation (Sec. 5.3.3). 25. Affidavit of compliance (Sec. 6.3). III.B. Modification to Standard. Any modification to the provisions, definitions, or terminology in this standard must be provided by the purchaser. I V. Major Revisions. The major changes made to the standard in this edition include the following: Copyright 2012 American Water Works Association. All Rights Reserved.