AWWA C226-2013 Stainless-Steel Fittings for Waterworks Service Sizes In Through 72 In (13 mm Through 1 800 mm).pdf

1、 ANSI/AWWA C226-13 (Revision of ANSI/AWWA C226-06) AWWA Standard Effective date: June 1, 2013. First edition approved by AWWA Board of Directors Feb. 12, 2006. This edition approved Jan. 20, 2013. Approved by American National Standards Institute March 14, 2013. 6666 West Quincy Avenue Advocacy Denv

2、er, CO 80235-3098 Communications T 800.926.7337 Conferences www.awwa.org Education and TrainingScience and TechnologySections The Authoritative Resource on Safe Water Stainless-Steel Fittings for Waterworks Service, Sizes 12 In. Through 72 In. (13 mm Through 1,800 mm) SM Copyright 2013 American Wate

3、r Works Association. All Rights Reserved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contained in spec

4、ifi- cations. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA publication of a standard does not constitute endorsement of any product or product typ

5、e, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or codes of any governmental authority. AWWA standards are intended to represent a consensus o

6、f the water supply industry that the product described will provide satisfactory service. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal - American Water Works Association. The action becomes effec

7、tive on the first day of the month following the month of Journal - American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National S

8、tandard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing, purchasing, or using products, pr

9、ocesses, or procedures not conforming to the standard. Ameri- can National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in

10、advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI app

11、roval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of ANSI approval. Purchasers of American National Standards may receive current i

12、nformation on all standards by calling or writ- ing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; (212) 642-4900, or emailing infoansi.org. ISBN-13, print: 978-1-58321-936-2 eISBN-13, electronic: 978-1-61300-229-2 ISBN-10, print: 1-58321-936-6 eISB

13、N-10, electronic: 1-61300-229-7 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quotations for revi

14、ew purposes, without the written permission of the publisher. Copyright 2013 by American Water Works Association Printed in USA Copyright 2013 American Water Works Association. All Rights Reserved. iii Committee Personnel The Steel Water Pipe Manufacturers Technical Advisory Committee Task Group (SW

15、PMTAC) on C226, which developed this edition, had the following personnel at the time: Niels Thogersen, Chair E. Bird, Smith-Blair, Texarkana, Texas (AWWA) S. Bradberry, Ford Meter Box Company, Pell City, Ala. (AWWA) A. Collins, JCM Industries, Nash, Texas (AWWA) T. Crail, Straub Coupling, Bonsall,

16、Calif. (AWWA) M. Fite, Pacific Coast Flange, Moundhouse, Nev. (AWWA) J. Grocki, SPLASH, Enfield, Conn. (AWWA) T. Keffaber, Ford Meter Box Company, Wabash, Ind. (AWWA) G. Kohlbeck, Felker Brothers, Marshfield, Wis. (AWWA) S. Lamb, Nickel Institute, Huntington, W.Va. (AWWA) D. Piontek, Total Piping So

17、lutions Inc., Olean, N.Y. (AWWA) D. Seals, JCM Industries, Nash, Texas (AWWA) K. Shaddix, Smith-Blair, Texarkana, Texas (AWWA) N. Thogersen, Romac Industries Inc., Bothell, Wash. (AWWA) M. Vanderbosch, CAB Incorporated, Oakwood, Ga. (AWWA) G. Washburn, Mfg. Consultant, Easton, Pa. (AWWA) The AWWA St

18、andards Committee on Stainless Steel Pipe, which reviewed and approved this standard, had the following personnel at the time of approval: J. Warren Green, Chair Mike Quinnell, Secretary General Interest Members R.J. Card,* Lockwood Andrews (2) external pressures, (3) special physical loading, and (

19、4) practical considerations for handling, shipping, lining and coating, or similar operations. II.A.1 Application. The provisions of this standard cover the requirements for stainless-steel fittings for the use in water treatment plants, water transmission and distribution systems, and other water f

20、acilities. The purchaser is responsible for determining if any circumstance related to the project requires additional provisions * NSF International, 789 N. Dixboro Road, Ann Arbor, MI 48106. Both publications are available from National Academy of Sciences, 500 Fifth Street NW, Washington, DC 2000

21、1. Appendix C of NSF/ANSI 61 defines those materials that are “Mechanical Devices Acceptable Materials,” which conform to NSF/ANSI 61 requirements. Copyright 2013 American Water Works Association. All Rights Reserved. ix that are not included in the standard. Such special conditions might affect des

22、ign, manufacture, quality control, corrosion protection, or handling requirements. II.A.2 Testing of special sections. Sec. 5.2.3 provides for nondestructive testing of special sections. III. Use of This Standard. It is the responsibility of the user of an AWWA Standard to determine that the product

23、s described in that standard are suitable for the use in the particular application being considered. III.A. Purchaser Options and Alternatives. The following information should be provided by the purchaser: 1. Standard usedthat is, ANSI/AWWA C226, Stainless-Steel Fittings for Waterworks Service, Si

24、zes 12 In. Through 72 In. (13 mm Through 1,800 mm), of latest revision. 2. Whether compliance with NSF/ANSI 61, Drinking Water System ComponentsHealth Effects, is required. 3. Internal working, transient, and test pressures. 4. Allowable stress in the fitting wall at specified internal design pressu

25、re (as a percentage of minimum yield point of stainless steel). 5. Minimum wall thickness required by considerations other than internal pressure. 6. The type of stainless steel (Sec. 4.1). 7. Details of other federal, state or provincial, and local requirements (Sec. 4.1.1). 8. Standard specificati

26、on of fitting, or plate, sheet, or strip, including material type (Sec. 4.1.8). 9. A description or drawings detailing the total quantity of fittings required for the length and diameter of fittings (see Table 2) (Sec. 4.2.1.5). 10. Welding (Sec. 4.2.3.1, Sec. 4.2.3.3, and Sec. 4.2.3.4). 11. Drawing

27、s and calculations to be provided by the manufacturer, when required (Sec. 4.2.1.8 and Sec. 4.2.4). 12. Coatings, if necessary (Sec. 4.2.1.9). 13. Type of ends for fittingsdescription or drawings (Sec. 4.2.2). 14. Qualification code for welding operators, if different from Sec. 4.2.3.1 or Sec. 5.2.1. 15. Special sections, indicating dimensions (Sec. 4.2.4.2 ) and the grade of material (Sec. 4.1.6). 16. Requirements for cleaning, descaling, and passivating (Sec. 4.2.5). 17. Method of nondestructive testing (Sec. 5.2.3.). Copyright 2013 American Water Works Association. All Rights Reserved.