AWWA C230-2016 Stainless-Steel Full- Encirclement Repair and Service Connection Clamps for 2-in Through 12-in (50-mm Through 300-mm) Pipe.pdf

1、AWWA Standard SM Stainless-Steel Full- Encirclement Repair and Service Connection Clamps for 2-in. Through 12-in. (50-mm Through 300-mm) Pipe Effective date: Dec. 1, 2016. First edition approved by AWWA Board of Directors Jan. 23, 2011. This edition approved June 19, 2016. Approved by American Natio

2、nal Standards Institute June 30, 2016. ANSI/AWWA C230-16 (Revision of ANSI/AWWA C230-11) Copyright 2016 American Water Works Association. All Rights Reserved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe min

3、imum requirements and do not contain all of the engineering and administrative information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service

4、 is not fully defined. AWWA pub- lication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any appli

5、cable law, regulation, or code of any governmental authority. AWWA standards are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the fi

6、rst page of the Official Notice section of Journal American Water Works Association. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard

7、 implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether tha

8、t person has ap - proved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods m

9、ade in conformity with an American National Standard are encour - aged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National St

10、andards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later

11、than five years from the date of publication. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. ISB

12、N-13, print: 978-1-62576-189-7 eISBN-13, electronic: 978-1-61300-398-5DOI: http:/dx.doi.org/10.12999/AWWA.C230.16 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any informatio

13、n or retrieval system, except in the form of brief excerpts or quotations for review purposes, without the written permission of the publisher. Copyright 2016 by American Water Works Association Printed in USA hours of work by your fellow water professionals. Revenue from the sales of this AWWA mate

14、rial supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of Copyright 2016 American Water Works Association. All Rights Reserved. iii Comm

15、ittee Personnel The Steel Water Pipe Manufacturers Technical Advisory Committee (SWPMTAC) Task Group for AWWA C230, which updated this standard, had the following personnel at the time: Daryl Piontek, Chair E. Bird, Smith-Blair, Texarkana, Texas (AWWA) S. Bradberry, Ford Meter Box Company, Birmingha

16、m, Ala. (AWWA) A. Collins, JCM Industries, Nash, Texas (AWWA) T. Crail, Straub Coupling, Bonsall, Calif. (AWWA) B. Dix, Felker Brothers, Marshfield, Wis. (AWWA) J. Grocki, Swepco Tube LLC, Enfield, Conn. (AWWA) C.G. Hines, Mueller Company, Cleveland, Tenn. (AWWA) T. Keffaber, Ford Meter Box Company,

17、 Wabash, Ind. (AWWA) M. Langenhan, Total Piping Solutions Inc., Olean, N.Y. (AWWA) G. Larsen, Smith Blair, Texarkana, Texas (AWWA) A. Lemke, Romac Industries Inc., Bothell, Wash. (AWWA) H. Mosley, Mueller Company, Cleveland, Tenn. (AWWA) D. Piontek, Total Piping Solutions Inc., Olean, N.Y. (AWWA) J.

18、 Reinheimer, Robar Industries, Surrey, B.C., Canada (AWWA) D. Seals, JCM Industries, Nash, Texas (AWWA) N. Thogersen, Romac Industries Inc., Bothel, Wash. (AWWA) A. Thoemke, Victaulic Company, Atlanta, Ga. (AWWA) The AWWA Standards Committee on Stainless-Steel Pipe, which reviewed and approved this

19、standard, had the following personnel at the time of approval: J. Warren Green, Chair Mike Quinnell, Secretary General Interest Members R.J. Card,* Lockwood, Andrews the structural integrity of the pipe; pipe material; pipe diameter; the pipeline content; surface finish; temperature; and working pre

20、ssure of the piping system. Because of the number of variables involved, it is recommended that the repair clamp manufacturer be consulted regarding model selection, proper application, and the anticipated performance of the repair clamp for specific end-user pipe repair needs prior to product purch

21、ase and usage. When * NSF International, 789 North Dixboro Road, Ann Arbor, MI 48105. Both publications available from National Academy of Sciences, 500 Fifth Street, NW, Washington, DC 20001. Copyright 2016 American Water Works Association. All Rights Reserved. ix significant damage to the pipe is

22、encountered, the manufacturer should be consulted to determine whether a repair clamp is appropriate for the repair. II.B. Chlorine and Chloramine Degradation of Elastomers. The selection of materials is critical for water service and distribution piping in locations where there is a possibility tha

23、t elastomers will be in contact with chlorine or chloramines. Documented research has shown that elastomers such as gaskets, seals, valve seats, and encapsulations may be degraded when exposed to chlorine or chloramines. The impact of degradation is a function of the type of elastomeric material, ch

24、emical concentration, contact surface area, elastomer cross section, and environmental conditions as well as temperature. Careful selection of and specifications for elastomeric materials and the specifics of their application for each water system component should be considered to provide long-term

25、 usefulness and minimum degradation (swelling, loss of elasticity, or softening) of the elastomer specified. III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular applicatio

26、n being considered. III.A. Purchaser Options and Alternatives. The fo llowing information should be provided by the purchaser: 1. Standard usedthat is, ANSI/AWWA C230, Stainless-Steel Full- Encirclement Repair and Service Connection Clamps for 2-In. Through 12-In. (50-mm Through 300-mm) Pipe, of lat

27、est revision. 2. Quantity and type. 3. Materials of construction. 4. Type of pipe(s), including specification to which it is made, or specification and tolerance of outside diameter. 5. Nominal pipe size(s) and range. 6. Actual outside diameter (OD) of pipe, including any coatings. 7. Wall thickness

28、 or class of pipe. 8. Type of service, including line content; above or below ground; and so on. 9. System pressure requirements. 10. Operating temperature range. 11. Special requirements, such as gasket material, gaskets for electrical conduc- tivity, corrosive environment, coatings, and so on. 12. Tapping outlet specifications (if required), including thread type and size. 13. Width of full-encirclement repair clamp band desired. 14. Inspection by the purchaser. Copyright 2016 American Water Works Association. All Rights Reserved.