AWWA C602-2011 Cement-Mortar Lining of Water Pipelines in Place-4 In (100 mm) and Larger.pdf

1、 ANSI/AWWA C602-11 (Revision of ANSI/AWWA C602-06) AW WA Standard Effective date: Oct. 1, 2011. First edition approved by AWWA Board of Directors June 17, 1955. This edition approved June 12, 2011. Approved by American National Standards Institute July 12, 2011. 6666 West Quincy Avenue Advocacy Denv

2、er, CO 80235-3098 Communications T 800.926.7337 Conferences www.awwa.org Education and Training Science and Technology Sections The Authoritative Resource on Safe Water CementMortar Lining of Water Pipelines in Place4 In. (100 mm) and Larger SM Copyright2011AmericanWaterWorksAssociation.AllRightsRes

3、erved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specication. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contained in speci- cations. The AWWA standards usuall

4、y contain options that must be evaluated by the user of the standard. Until each optional feature is specied by the user, the product or service is not fully dened. AWWA publication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve

5、any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or codes of any governmental authority. AWWA standards are intended to represent a consensus of the water supply industry that the produc

6、t described will provide satisfactory service. When AWWA revises or withdraws this standard, an ofcial notice of action will be placed in the ofcial notice section of Journal AWWA. The action becomes effective on the rst day of the month following the month of Journal AWWA publication of the ofcial

7、notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American Nation

8、al Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. Ameri- can National Standards are subject to periodic review, and users ar

9、e cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American Nat

10、ional Standards. CAUTION NOTICE: The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken

11、 to reafrm, revise, or withdraw this standard no later than ve years from the date of publication. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York,

12、NY 10036; (212) 642-4900, or e-mailing infoansi.org. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts o

13、r quotations for review purposes, without the written permission of the publisher. Copyright 2011 by American Water Works Association Printed in USA Copyright2011AmericanWaterWorksAssociation.AllRightsReserved. iii Committee Personnel e Steel Water Pipe-Manufacturers Technical Advisory Committee (SW

14、PMTAC) Task Group for C602, which developed this standard, had the following personnel at the time: Bruce J. Britton, Chair H.H. Bardakjian, Consultant, Glendale, Calif. (AWWA) B.J. Britton, W. Walsh Company, Attleboro, Mass. (AWWA) R.J. Card, Lockwood Andrews limits of pipeline shutdowns, if service requirements * NSF International, 789 N. Dixboro Road, Ann Arbor, MI 48105. Both publications available from National Academy of Sciences, 500 Fifth Street, N. W., Washington, DC 20001. Copyright2011AmericanWaterWorksAssociation.AllRightsReserved.