BHMA A156 6-2015 ARCHITECTURAL DOOR TRIM《建筑装饰门》.pdf

1、ANSI/BHMA A156.6-2015 Revision of ANSI/BHMA A156.6-2010 AMERICAN NATIONAL STANDARD FOR ARCHITECTURAL DOOR TRIM SPONSOR BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. AMERICAN NATIONAL STANDARDS INSTITUTE Approved December 23, 2015 2 AMERICAN NATIONAL STANDARD An American National Standard implies

2、 a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has appro

3、ved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American National Sta

4、ndard is permitted to be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards receive c

5、urrent information on all standards by calling or writing the American National Standards Institute. Published by BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. 355 Lexington Avenue, New York, New York 10017 Copyright 2015 by the Builders Hardware Manufacturers Association, Inc. Not to be reprod

6、uced without specific authorization from BHMA Printed in the USA This standard was first published December 1969 by the Builders Hardware Manufacturers Association, Inc. It was entitled, “Standard 1001 BHMA Product Standards Section J, Architectural Door Trim.” This Standard was approved by ANSI und

7、er the Canvass Method. BHMA was accredited on 21 March 1983 as a sponsor using the Canvass Method.3 FOREWORD (This Foreword is not a part of ANSI/BHMA A156.6) The general classification of builders hardware includes a wide variety of items which are divided into several categories. To recognize this

8、 diversity, a sectional classification system has been established. Architectural Door Trim is one such section and this Standard is a result of the collective efforts of members of the Builders Hardware Manufacturers Association, Inc. who manufacture this product. The total Product Standards effort

9、 is, therefore, a collection of sections, each covering a specific category of items. Performance tests and, where it has been necessary, material and dimensional requirements have been established to insure safety and stability to which the public is entitled. There are no restrictions on design ex

10、cept for those dimensional requirements imposed for reasons given above. The BHMA recognizes that errors will be found, items will become obsolete, and new products, methods and materials will be developed. With this in mind, the Association plans to update, correct and revise these Standards on a r

11、egular basis. The BHMA numbers which indicate types and functions of hardware do not identify size, finish, material or design and are not intended to be used without necessary supplementary information. Users of this Standard who require a specific design for a product type should describe it, usin

12、g generic terms or the manufacturers name and description of the product desired. 4 TABLE OF CONTENTS 1. SCOPE 5 2. DEFINITIONS 5 3. GENERAL 5 4. PRODUCT CATEGORY J100 - DOOR PROTECTION PLATES 6 5. PRODUCT CATEGORY J200 - DOOR EDGINGS 7 6. PRODUCT CATEGORY J300 - PUSH PLATES 8 7. PRODUCT CATEGORY J4

13、00 - DOOR PULLS AND PUSH/PULL UNITS 9 8. PRODUCT CATEGORY J500 - PUSH BARS AND PULL BARS 11 9. FINISH TESTS 13 APPENDIX A (NOT A PART OF ANSI/BHMA A156.6) 15 5 1. SCOPE 1.1 This Standard contains requirements for door protection plates, door edgings, push plates, door pulls, push bars, and pull bars

14、. Included are strength and finish tests, and dimensional and material criteria. 1.2 Tests described in this Standard are performed under laboratory conditions. In actual usage, results vary because of installation, maintenance and environmental conditions. 2. DEFINITIONS 2.1 Door Edging Protective

15、material applied to the edge of a door. 2.2 Door Protection Plate Protective material applied to the face of a door. 2.3 Door Pull A device applied to the face of a door and when grasped permits the user to pull a door open. 2.4 Kick Plate A protective plate applied to the lower part of the door sur

16、face on the closing side of the door. 2.5 Mop Plate A protective plate applied to the lower part of the door surface on the opening side of the door. 2.6 Pull Plate An assembly consisting of a door pull with a protective material positioned between the pull and face of a door. 2.7 Pull Bar A device

17、extending across or vertically on a door and when grasped permits the user to pull a door open. 2.8 Push Bar Similar to pull bar but used for pushing a door open. 2.9 Push Plate Material applied to the surface of a door and located where a user is to push on a door to open it. 2.10 Push/Pull Unit A

18、non-latching device applied to the face of a door and offering suitable surfaces for either a pushing or pulling operation of the door. 2.11 Stretcher Plate A protective plate applied to the middle part of the door surface on either side of the door. 3. GENERAL 3.1 Reference to other Standards ANSI

19、Standards referenced in this Standard are available from the Builders Hardware Manufacturers Association, , or American National Standards Institute www.ansi.org . 3.2 Dimensions All dimensions are given in US units with approximate SI (metric) conversions. Where plus or minus tolerances are not giv

20、en, values are permitted to be correspondingly reduced or exceeded at the option of the manufacturer within the functional limitations of the product. 3.3 Workmanship Products meeting this Standard shall be free of imperfections and defects affecting appearance, durability and service. 3.4 Materials

21、 Materials to be used are listed in the product category description. Experience has shown these will provide a serviceable product. Where brass is mentioned, reference is to mean yellow brass, red brass or 90% commercial bronze. Metal used shall be determined by the finish specified for the product

22、. 6 Wherever stainless steel is mentioned, reference is to mean 300 series stainless steel. 3.5 Finish Finishes shall conform to the finish test values in this Standard for all applicable products. Appearance and test procedures shall conform to ANSI/BHMA A156.18-2012 for Materials and Finishes. All

23、 visible parts when the product is installed shall match subject to the limitations stated under the product category and to natural variations of those finishes falling into B or C categories. The finish of exposed screw and bolt heads shall be compatible with that of the product subject to these v

24、ariations. Fasteners not exposed shall have a corrosion resistant finish. 3.6 Packaging All products together with necessary screws and other fasteners shall be wrapped or packaged individually unless otherwise specified by the manufacturer. The package shall be labeled or marked to clearly indicate

25、 contents. 3.7 Symbols The symbol CTC used throughout this Standard means center to center. All other symbols are defined as they are used. 4. PRODUCT CATEGORY J100 - DOOR PROTECTION PLATES 4.1 These products are surface applied. They shall meet the finish requirements listed under 9. 4.2 Materials

26、4.2.1 Metals 0.050 in. (1.3 mm) nominal or thicker aluminum, brass or stainless steel. 4.2.2 Other Materials 4.2.1.1 Laminate Plastic: 1/8 in. (3.2mm) minimum thickness. 4.2.1.2 Clear Plastic: 1/8 in. (3.2mm) minimum thickness. 4.2.1.3 Flexible PVC or Acrylic Alloy Plastics: 0.060 in. (1.5mm) minimu

27、m thickness. 4.2.1.4 Consult applicable fire codes for use of materials other than metal on fire rated openings. 4.3 Workmanship 4.3.1 For a given size, height is stated first (height x width). Combination plates require separate sizes for each part. 4.3.2 Screw holes shall be spaced equidistant 8 i

28、n. (203 mm) maximum CTC, along a centerline not over 1/2 in. (12.7 mm) in from the edge all around the plate. The end screws shall also be a maximum of 0.53 in. (13 mm) from the corners. (See A - 1.1 and A - 1.2) 4.3.3 Attachment screws shall be furnished with the plate. The standard screw is stainl

29、ess steel no. 6 Phillips head, type AB tapping 5/8 in. (16 mm) minimum length with finish compatible with that of the plate. Screw heads other than Phillips are permitted as specified. (See A - 1.1 and A - 1.2) 4.3.4 Polishing lines or dominant direction of any surface pattern shall run across the d

30、oor (width of plate). Users of this Standard wishing wood grained plastic plates with grain running in the same direction as the grain in the door shall so specify. 4.3.5 Beveled edges are optional on metal plates and standard on other materials 1/8 in. (3.2 mm) thick or thicker. They shall be unifo

31、rmly beveled leaving no sharp edges. Bevel the top and two sides of metal plates (symbol B3E) and all sides of other materials (symbol B4E). Edges on metal plates shall be deburred. 4.3.6 Options Symbol ARS - provide an additional row of screw holes spaced equidistant on 8 in. (203 7 mm) CTC maximum

32、 along the horizontal centerline of the armor plate (See Figure 1). 4.3.7 Cut-outs Plates are permitted to be ordered with cut-outs to provide for cylinders, louvers, door lites, etc. 4.4 Tolerances Size 1/16 in. (1.6 mm). Squareness of corners 1/2 degree. Thickness 10%. All other dimensions 1/32 in

33、. (0.8 mm). FIGURE 1 - DOOR PROTECTION PLATE ILLUSTRATIONS AND TYPE NUMBERS Kick Plate Metal - J102 Plastic J106 Armor Plate Metal J101 Plastic J105 Mop Plate Metal J103 Plastic J107 Combination Plate 5. PRODUCT CATEGORY J200 - DOOR EDGINGS 5.1 These products are either surface or, for wood or decor

34、ative laminate doors, mortise applied. They shall meet the finish requirements listed under 9. 5.2 Materials Metals 0.050 in. (1.3 mm) minimum thick aluminum brass, or stainless steel. 5.3 Workmanship 5.3.1 For a given size, state height, bevel and thickness of door. 5.3.2 Countersunk screw holes sh

35、all be equidistant 8 in. (203 mm) CTC maximum along door edge leg not over 1/2 in. (12.7 mm) in from door faces. (See Figure 2.) 5.3.3 Polishing lines shall run up and down the door (height of edging). 5.3.4 Attachment screws shall be furnished with the edging. The standard screw is stainless steel

36、no. 6 Phillips flat head type AB tapping 5/8 in. (16 mm) minimum length. Screw heads other than Phillips are permitted as specified. 5.3.5 The 87 degrees and 93 degrees references in Figure 2 are approximate. Edgings shall fit door bevel of 1/8 in. (3.2 mm) in 2 in. (50.8 mm). 5.3.6 Length of leg on

37、 face of door Mortise type 7/8 in. (22.2 mm), non-mortise type 1 1/4 inch (31.2 mm). Length of leg on door edge shall protect that surface and is therefore dependent on actual thickness of the door. 5.3.7 Options Symbol M - leg offset on non-mortise type for 0.050 in. (1.3 mm) metal plate. Symbol P

38、- leg offset on non-mortise type 1/8 in. (3.2 mm) plastic plate. Type, size, and location shall be given before cutout is made. 8 5.3.8 Cut-outs Door edgings are permitted to be ordered with cut-outs to provide for hinges or latches etc. 5.3.9 Edges shall be deburred. 5.4 Tolerances Height 1/16 in.

39、(1.6 mm). Squareness of square or beveled edging 1/4 degree. Thickness of edging 10%. Leg on edge of door: angle types + 0 - 1/16 in. (1.6 mm), mortise cap type + 0 - 1/32 in. (0.8 mm), non-mortise cap type + 1/32 in. (0.8 mm) - 0. Other Dimensions 1/32 in. (0.8 mm). For J212, the tolerance for the

40、end radius shall be in. (6.4 mm). FIGURE 2 - DOOR EDGING ILLUSTRATIONS AND TYPE NUMBERS Armor Plate Under J201 J202 Non Mortise Angle Types Specify M Option i.e. J201P Armor Plate Over J204 J205 Mortise Angle Types J207 J208 J209 Non Mortise Cap Types Specify M Option i.e. J207P J210 J211 J212 Morti

41、se Cap Types 6. PRODUCT CATEGORY J300 - PUSH PLATES 6.1 These products are surface applied. They shall meet the finish requirements listed under 9. 6.2 Materials 6.2.1 Metals 0.050 in. (1.3 mm) minimum and 1/8 in. (3.2 mm) minimum thick aluminum, brass or stainless steel. 6.2.2 Other 1/8 in. (3.2 mm

42、) minimum thick laminated plastic or .060 in. (1.5 mm) minimum thick solid plastic. (See 4.2.2) 6.2.3 Metal thickness of cold forged plates (J302) shall be 0.050 in. (1.3 mm) minimum. 6.2.4 Minimum thickness of Push Pull. Plate J303 shall be 1/8 in. (3.2 mm). 6.3 Workmanship 9 6.3.1 For a given size

43、, width is stated first (width x height). 6.3.2 Shape or design of a plate shall be produced to the manufacturers specifications. 6.3.3 Screw holes, not less than six, shall be spaced equidistant 9 in. (229 mm) maximum CTC along a centerline not over 1/2 in. (12.7 mm) in from the edge all around the

44、 plate and counter-sunk for no. 6 screws. The end screws shall also be a maximum of 0.53 in. (13 mm) from the corners. 6.3.4 Polishing lines or dominant direction of any surface pattern shall run parallel to the longer dimension, width or height. Users of this Standard wishing wood grained plastic p

45、lates with grain running in the same direction as the grain in the door shall so specify. 6.3.5 Attachment screws shall be furnished with the plate. Standard screws are stainless steel no. 6 Phillips undercut head, type AB tapping 5/8 in. (16 mm) minimum length with finish compatible with that of th

46、e plate. 6.3.6 Beveled edges are standard on rectangular J301 and optional depending on design and shall be uniformly beveled leaving no sharp edges. Edges shall be deburred. 6.3.7 Raised lip on plates of J303 design shall be an integral part of the plate with 1 in. (25.4 mm) minimum projection and

47、2 in. (50.8 mm) maximum extension below the plate surface resting on the door. The lip shall have no sharp edges or corners. 6.3.8 Options Symbol CFC - Provide cutout for lock cylinder as specified. Symbol CFT - Provide cutout for thumb turn as specified. Symbol CFBK - Provide cutout for bit key as

48、specified. 6.4 Standard Push Plate 6.4.1 Push plates are available in a variety of sizes and designs. Make reference to an individual manufacturers catalog. When no specific manufacturers catalog number is specified, a TYPE J301 rectangular plate with square corners (90 degrees) and beveled edges in

49、 material, finish and size as specified shall be furnished. 6.5 Tolerances Size 1/16 in. (1.6 mm). Squareness of plate when applicable to design 90 degrees 1/4 degrees. Thickness 10%. All other dimensions 1/32 in. (0.8 mm). FIGURE 3 PUSH PLATE ILLUSTRATIONS AND TYPE NUMBERS Illustrations are to define but not to limit product design. Flat Plate 0.050 in. (1.3 mm) thick J301 1/8 in. (3.2 mm) thick J304 Cold Forged J302 Push-Pull Plate J303 7. PRODUCT CATEGORY J400 - DOOR PU