BS 1123-2006 Fusible plugs for steam boilers and compressed air applications - Specification《蒸汽锅炉和压缩空气设备用易熔塞 规范》.pdf

1、BS 1123:2006Fusible plugs for steam boilers and compressed air applications SpecificationICS 13.240; 97.120NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPublishing and copyright informationThe BSI copyright notice displayed in this document indicates when the

2、document was last issued. BSI 2006ISBN 0 580 48468 8The following BSI references relate to the work on this standard:Committee reference PVE/12Draft for comment 05/30029968 DCPublication historyFirst published, July 1943Second edition, February 1950Third edition, July 1961Fourth edition, October 197

3、6Fifth edition, as Part 1, February 1987Sixth edition, July 2006Amendments issued since publicationAmd. no. Date Text affectedBS 1123:2006 BSI 2006 iBS 1123:2006ContentsForeword ii1 Scope 12 Normative references 13 Terms and definitions 14 Construction 15 Materials 26 Marking 27 Instructions 2AnnexA

4、nnex A (informative) Installation and safe use 3Bibliography 4Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover.ii BSI 2006BS 1123:2006ForewordPublishing informationThis British Standard was published by

5、BSI and came into effect on 20 July 2006. It was prepared by Technical Committee PVE/12, Safety devices. SupersessionIt supersedes BS 1123-1:1987, which is withdrawn. Information about this documentIt has been prepared to:1) consolidate requirements for fusible plugs from BS 759-1:19841)and BS 1123-

6、1:1987 into one standard;2) remove potential overlap with BS EN ISO 4126-1:2004. This British Standard provides requirements for the design and guidance on the installation of fusible plugs for the steam boiler and compressed air industries for which a European or international standard does not cur

7、rently exist. Contractual and legal considerationsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. 1)At the time of publication

8、 BS 759-1:1984 is being revised and the new edition will not cover fusible plugs. BSI 2006 1BS 1123:20061 Scope This British Standard specifies design requirements for fusible plugs for use in steam boilers and compressed air installations.Guidance on installation is included in Annex A.NOTE Fusible

9、 plugs do not provide protection against excessive pressure, i.e. they do not remove the requirement for a safety device(s).2 Normative referencesThe following referenced document is indispensable for the application of this document. For dated references, only the edition cited applies. For undated

10、 references, the latest edition of the referenced document (including any amendments) applies.BS 21, Specification for pipe threads for tubes and fittings where pressure-tight joints are made on the threads (metric dimensions)3 Terms and definitionsFor the purposes of this British Standard, the foll

11、owing term and definition apply.3.1 fusible plugtemperature-activated non-closing pressure relief device, containing fusible metal designed to melt at a pre-determined temperature4 Construction 4.1 Steam boiler applications Fusible plugs for steam boiler applications shall consist of an outer body w

12、ith a central passage, which may be either parallel or conical. The smallest diameter of the central passage shall be not greater than 13 mm for plugs suitable for pressures up to 7 bar, and be not greater than 10 mm for pressures exceeding 7 bar. The passage shall be closed with a central core secu

13、red by an annular lining of fusible metal, designed to allow the core to drop clear if the lining melts.NOTE A portion of the body carrying the fusible metal may be detachable from the base to allow easy replacement without removing the whole fitting from the boiler.4.2 Compressed air applications F

14、usible plugs for compressed air applications shall consist of a holder with a central passage closed by fusible metal. The outlet shall be provided with a diffuser cap capable of arresting and containing the ejected metal. The inlet connection of the holder shall be threaded not less than R3/8 in ac

15、cordance with BS 21.BS 1123:20062 BSI 20065 Materials5.1 GeneralThe manufacturer shall take into account the full details of the application in order for the correct materials to be selected.NOTE Details may include: temperature;pressure;fluid;pressure vessel material.5.2 Non-fusible components Non-

16、fusible components of the plug shall be of copper alloy, except where this is incompatible with the application criteria in 5.1 eg. fluid chemical compatibility.5.3 Fusible component For steam boiler applications the fusible component of the plug shall be of a metal which melts readily at a temperat

17、ure not less than 90 C and not greater than 200 C in excess of the saturated steam temperature at the design pressure of the boiler. For compressed air applications the fusible component of the plug shall be of metal with a melting point to suit the application. 6 Marking The melting temperature or

18、temperature range in C shall be permanently marked on the fusible plug. NOTE Where the fusible plug is too small to permit the temperature to be marked, a suitable traceable code may be used.7 Instructions The manufacturer shall provide clear written instructions relating to the installation of fusi

19、ble plugs and their safe use.NOTE Guidance on the installation and safe use of fusible plugs is given in Annex A. BSI 2006 3BS 1123:2006Annex A (informative) Installation and safe useA.1 GeneralDischarge through fusible plugs should not be used to provide over pressure protection i.e. they do not re

20、move the requirement for a safety device(s).Consideration should be given to the positioning of the fusible plug to ensure that the discharge does not cause damage or injury to persons and property.It is essential that fusible plugs are installed the correct way round, otherwise during operation the

21、 core could jam in the passageway and render the device useless.A.2 Steam boiler applicationsFusible plugs should be fitted at a sufficient height and in such a position as to give an early warning in the event of shortage of water to all parts of the boiler liable to damage by the direct applicatio

22、n of furnace heat. Fusible plugs should be installed so that their discharge is directed onto the source of heat. However, they should also be installed so that as far as practical they are shielded from the path of direct flames.It is essential that fusible plugs are installed the correct way round

23、. A fusible plug may be designed to be installed from the “fire-side” or may be designed to be installed from the “water-side”. It needs to be installed in the attitude it was designed for i.e. with the pressure on the appropriate side of the fusible plug.A.3 Compressed air applicationsFusible plugs

24、 should be fitted between the compressor and the after-cooler (if any), or between the compressor and the receiver. They should be fitted as close to the compressor outlet as practicable, and situated so that the discharge from the plug cannot cause injury or damage to persons or property.On compres

25、sed air vessels the fusible plug should be fitted at or near the top of the vessel.A.4 Safe useFusible plugs should be cleaned and inspected regularly to assure continued protection, for example fusible plugs on steam boilers can be affected by scale and other deposits and should be cleaned and repl

26、aced as necessary.BS 1123:20064 BSI 2006BibliographyStandards publicationsFor dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.BS EN ISO 4126-1:2004, Safety devices for protection against excess

27、ive pressure Part 1: Safety valvesFurther readingBS EN ISO 4126-2, Safety devices for protection against excessive pressure Part 2: Bursting disc safety devicesBS EN ISO 4126-4, Safety devices for protection against excessive pressure Part 4: Pilot operated valvesBS EN ISO 4126-5, Safety devices for

28、 protection against excessive pressure Part 5: Controlled safety pressure relief systems (CSPRS)This page deliberately left blankBS 1123:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Euro

29、pe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products

30、 and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI o

31、ffers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax:

32、 +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Informa

33、tion on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the

34、 Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Adminis

35、tration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists

36、in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any mea

37、ns electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager.Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.Email: copyrightbsi-.BS 1123:2006389 Chiswick High RoadLondonW4 4AL