BS 1127-5-1990 Screwing dies and dienuts - Specification for dimensions of hexagon dienuts《螺丝板牙和螺母状板牙 六角形螺母状板牙尺寸规范》.pdf

1、BRITISH STANDARD BS1127-5: 1990 ISO7226:1988 Screwing dies and dienuts Part5: Specification for dimensions of hexagonal dienuts UDC 621.992.31BS1127-5:1990 This BritishStandard, having been prepared under the directionof the Machine, Engineers and Hand Tools Standards Policy Committee, waspublished

2、under the authorityof the Board of BSI andcomes into effect on 29June1990 BSI12-1999 First published November1943 First revision June1950 Second revision September1974 Second edition June1990 The following BSI references relate to the work on this standard: Committee reference MTE/4 Draft for commen

3、t 87/72648 DC ISBN 0 580 18565 6 Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Machine, Engineers and Hand Tools Standards Policy Committee (MTE/-) to Technical Committee MTE/4, upon which the following bodies were represented: Advanced

4、Manufacturing Technology Research Institute British Electrical Systems Association (BEAMA Ltd.) Federation of British Engineers Tool Manufacturers Gauge and Tool Makers Association Institution of Production Engineers Screw Thread Tool Manufacturers Association Society of British Aerospace Companies

5、Limited Twist Drill and Reamer Association Amendments issued since publication Amd. No. Date of issue CommentsBS1127-5:1990 BSI 12-1999 i Contents Page Committees responsible Inside front cover National foreword ii 0 Introduction 1 1 Scope and field of application 1 2 References 1 3 Dimensions and t

6、olerances 1 4 Marking 1 Figure Dimensions 1 Table 1 General table of dimensional characteristics of hexagonaldienutsfor metric and inch threads 2 Table 2 Table of dimensional characteristics of hexagonal dienutsforRseriespipe threads 2 Publications referred to Inside back coverBS1127-5:1990 ii BSI 1

7、2-1999 National foreword This Part of BS1127 has been prepared under the direction of the Machine, Engineers and Hand Tools Standards Policy Committee. It is identical with ISO7226:1988 “Hexagonal dienuts” published by the International Organization for Standardization (ISO). This Part of BS1127 tog

8、ether with Parts1,2,3 and4 supersedes BS1127:1974 which is withdrawn. BS1127 comprises the following Parts. Part1: Specification for hand- and machine-operated circular screwing dies and hand-operated die stocks; Part2: Specification for hand- and machine-operated circular screwing dies for taper pi

9、pe threads; R series; Part3: Specification for hand- and machine-operated circular screwing dies for parallel pipe threads; G series; Part4: Terminology for circular screwing dies; Part5: Specification for dimensions of hexagonal dienuts. BS1127 was first published in1943 as a war emergency standard

10、 and revised in1950 to include hexagonal dienuts and again in1974 to incorporate the change from inch to metric dimensions. The purpose of this present revision is to take account of changes made to related ISO standards since1974 and the requirement of the United Kingdom as a CEN member to give Eur

11、opean Standards EN22568, EN24230, EN24231 and EN25968 the status of national standards. ISO7726:1988, which was not adopted by CEN, is included for completeness of the screwing die series of standards. Cross-references International Standard Corresponding BritishStandard ISO7-1:1982 BS21:1985 Specif

12、ication for pipe threads for tubes and fittings where pressure-tight joints are made on the threads (metric dimensions) (Technically equivalent) ISO68:1973 BS3643: ISO metric screw threads Part1:1981 Principles and basic data (Technically equivalent) ISO228-1:1982 BS2779:1986 Specification for pipe

13、threads for tubes and fittings where pressure-tight joints are not made on the threads (metric dimensions) (Technically equivalent) ISO261:1973 BS3643 ISO metric screw threads Part1:1981 Principles and basic data (Technically equivalent) ISO263:1973 BS1580 Specification for Unified screw threads Par

14、ts1 R series (Identical)BS1127-5:1990 BSI 12-1999 iii A related BritishStandard to ISO68 is BS1580 “Specification for unified screw threads” Part3:1965 “Diameters below ! in”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are re

15、sponsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. International Standard Corresponding BritishStandard ISO4231:1987 Part3:1990 Specification for hand- and machine-operated circular screwing dies for parallel pipe th

16、reads; G series (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesitoiv, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amend

17、ment table on the inside front cover.iv blankBS1127-5:1990 BSI 12-1999 1 0 Introduction Circular screwing dies are specified for certain thread forms in ISO2568, ISO4230 and ISO4231. For certain sizes of these threads, it is convenient for some purposes to use hexagonal dienuts instead of circular d

18、ies and, for purposes connected with their manufacture and use, it is desirable that certain dimensions of these dienuts should be standardized. 1 Scope and field of application This International Standard specifies the general dimensions of hexagonal dienuts for certain sizes of ISO metric threads

19、(coarse and fine pitch series see ISO68 and ISO261), ISO inch threads (UNCand UNF series see ISO68 and ISO263), and pipe threads (G and R series see ISO7-1 and ISO228-1), as well as the non-preferred thread series BSW, BSF and BA. 2 References ISO7-1, Pipe threads where pressure-tight joints are mad

20、e on the threads Part1: Designation, dimensions and tolerances. ISO68, ISO general purpose screw threads Basic profile. ISO228-1, Pipe threads where pressure-tight joints are not made on the threads Part1: Designation, dimensions and tolerances. ISO261, ISO general purpose metric screw threads Gener

21、al plan. ISO263, ISO inch screw threads General plan and selection for screws, bolts and nuts Diameter range0,06 to6in. ISO2568, Hand- and machine-operated circular screwing dies and hand-operated die stocks. ISO4230, Hand- and machine-operated circular screwing dies for taper pipe threads R series.

22、 ISO4231, Hand- and machine-operated circular screwing dies for parallel pipe threads G series. 3 Dimensions and tolerances See the Figure, and Table 1 and Table 2. 4 Marking Dienuts having dimensions in accordance with those given in Table 1 shall be marked with the relevant thread designation spec

23、ified in ISO2568. Dienuts having dimensions in accordance with those given in Table 2 shall be marked with the letter R immediately followed by the designation of the thread. Example: A hexagonal dienut for R series pipe threads with designation1/8 shall be marked as follows: R1/8 Where tools comply

24、 in all respects with the relevant International Standards, the symbol ISO may be appended to the mark at the discretion of the manufacturer. Figure DimensionsBS1127-5:1990 2 BSI 12-1999 Table 1 General table of dimensional characteristics of hexagonal dienuts for metric and inch threads (except R s

25、eries pipe threads) Table 2 Table of dimensional characteristics of hexagonal dienuts for R series pipe threads Range of thread diameter, d s h13 mm Metric pitches mm in 0,35 0,7 0,73 0,81 0,9 1 1,25 1,5 1,75 2 2,5 3 3,5 4 4,5 5 5,5 Over Up to and including Over Up to and including Number of threads

26、 per inch 48 40 36 32 28 24 22 18 16 14 13 12 11 10 9 8 7 6 5 41/2 Cutting width, E (mm) js13 2,65 4 0,104 3 0,157 5 18 5 a 7 4 6,35 0,157 5 0,25 7 7 7 6,35 9 0,25 0,354 3 21 9 9 9 9 11,2 0,354 3 0,440 9 27 11 11 11 11 11,2 15 0,440 9 0,590 6 36 10 a 10 a 14 14 15 21,2 0,590 6 0,834 6 41 14 a 14 a 1

27、4 a 18 18 21,2 26,5 0,834 6 1,043 3 50 16 a 16 a 16 a 22 22 26,5 37,5 1,043 3 1,476 4 60 18 a 18 a 18 a 18 a 25 25 25 37,5 42,5 1,476 4 1,673 2 70 20 a 20 a 20 a 30 30 42,5 53 1,673 2 2,086 6 85 22 a 22 a 22 a 36 36 36 36 53 63 2,086 6 2,480 3 100 22 a 22 a 22 a 36 36 36 a These cutting widths, whic

28、h are the lower of the two values specified for each range of thread diameter, may be increased to the higher value given in the table at the discretion of the manufacturer. Designation Basic diameter mm Approximate pitch mm s h13 mm Cutting width, E js13 mm 1/16 7,723 0,907 21 10 1/8 9,728 0,907 27

29、 10 1/4 13,157 1,337 36 14 3/8 16,662 1,337 41 15 1/2 20,955 1,814 50 19 3/4 26,441 1,814 60 20 1 33,249 2,309 60 24 1 1/4 41,91 2,309 85 26 1 1/2 47,803 2,309 85 26 2 59,614 2,309 100 31BS1127-5:1990 BSI 12-1999 Publications referred to See national foreword.BS1127-5: 1990 ISO7226:1988 BSI 389 Chis

30、wick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by a

31、mendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard

32、would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of

33、 standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been p

34、ublished as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also availabl

35、e which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other ben

36、efits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act

37、1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details

38、 such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.