BS 1188-1974 Specification for ceramic wash basins and pedestals《陶瓷盥洗盆与台座规范》.pdf

1、BRITISH STANDARD BS1188:1974 (Reprinted, incorporating Amendment Nos. 1, 2 and 3) Specification for Ceramic wash basins and pedestals UDC696.143:691.434:666.596+666.645BS1188:1974 This British Standard, having been approved by the Sanitary Appliances Industry Standards Committee, was published under

2、 the authority of the Executive Board on13 May, 1974 BSI04-1999 First published March 1945 First revision December 1965 Second revision May 1974 The following BSI references relate to the work on this standard: Committee reference SAB/1 Draft for approval72/11901 ISBN0 580 08493 0 Co-operating organ

3、izations The Sanitary Appliances Industry Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Association of Public Health Inspectors* Institution of Munici

4、pal Engineers* British Bath Manufacturers Association* Institution of Public Health Engineers* British Plastics Federation* Metal Sink Manufacturers Association* British Waterworks Association Ministry of Defence, Air Force Department Council of British Ceramic Sanitaryware National Brassfoundry Ass

5、ociation* Manufacturers* National Federation of Builders and Plumbers Department of the Environment* Merchants* Department of the EnvironmentBuilding Royal Institute of British Architects* Research Establishment* Royal Institute of Public Health and Hygiene Greater London Council* Royal Society of H

6、ealth Institute of Plumbing* Water Companies Association Institution of Heating and Ventilating Engineers The Government departments and scientific and industrial organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entruste

7、d with the preparation of this British Standard: British Ceramic Research Association Good Housekeeping Institute British Ironfounders Association Institution of Water Engineers British Steel Industry Modular Society British Woodwork Manufacturers Association National Federation of Plumbers and Cons

8、umer Standards Advisory Committee of Domestic Heating Engineers BSI South London Consortium Department of Health and Social Security Individual manufacturers Amendments issued since publication Amd. No. Date of issue Comments 2038 June 1976 4093 December 1982 4914 April1989 Indicated by a sideline i

9、n the marginBS1188:1974 BSI 04-1999 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 General 1 1.1 Scope 1 1.2 Inspection 1 1.3 Rejection 1 1.4 Manufacturers certificate 1 1.5 Marking 1 1.6 Options 1 2 Materials 1 2.1 General 1 2.2 Quality 1 3 Design and construction 1 3.1

10、 General 1 3.2 Tap holes 1 3.3 Pedestals 1 3.4 Waste hole 2 3.5 Bracket studs 2 3.6 Colour 2 3.7 Overflow 2 3.8 Soap sinkings 2 3.9 Chain stay hole 2 4 Types, masses, dimensions and permissible deviations 3 4.1 Types 3 Figure 1 Details of outlets 2 Table 1 Dimensions and masses 3 Table 2 Ancillary d

11、imensions 3 Publication referred to Inside back coverBS1188:1974 ii BSI 04-1999 Foreword This British Standard, prepared under the authority of the Sanitary Appliances Industry Standards Committee, has been metricated in accordance with the metrication programme of the British Standards Institution.

12、 The recommendations for the co-ordination of dimensions in building as laid down in BS2900 “Recommendations for the co-ordination of dimensions in building. Glossary of terms”, and BS4011 “Recommendations for the co-ordination of dimensions in building. Basic sizes for building components and assem

13、blies” are embodied where appropriate in this standard. The metric values are given in SI units; for further information reference should be made to BS3763 “The International System of units (SI)” and PD5686, “Theuse of SI units”. The revision of this British Standard has been aimed at retaining the

14、 main dimensions of the previous issue, but allowing manufacturers freedom of design within these requirements. To this end the dimensions have been listed in tabular form and any illustrations likely to be misconstrued as indicating design have been eliminated. The materials known as stoneware and

15、earthenware have been omitted as they are no longer used in an appreciable quantity. The British Standards dealing with the quality of material, and finish, of vitreous china, taps and wastes suitable for these wash basins are as follows: BS504, Drawn lead traps. BS1010, Draw-off taps and stopvalves

16、 for water services (screwdown pattern). BS1184, Copper and copper alloy traps. BS3380, Wastes for sanitary appliances and overflows for baths Part 1. Wastes (excluding skeleton sink wastes) and bath overflows. BS3402, Quality of vitreous china sanitary appliances. BS3943, Plastics waste traps. Cert

17、ification. Attention is drawn to the certification facilities described on the inside back cover of this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Br

18、itish Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments inc

19、orporated. This will be indicated in the amendment table on theinside front cover.BS1188:1974 BSI 04-1999 1 1 General 1.1 Scope This British Standard specifies requirements for dimensions and quality for two sizes of ceramic wash basins with or without an overflow and/or a chain stay hole and for ce

20、ramic pedestals. NOTEThe title of the British Standard referred to in this standard is given on the inside back cover. 1.2 Inspection The purchaser or his representative shall, if required, be granted facilities for the purpose of carrying out inspection prior to delivery. 1.3 Rejection The purchase

21、r shall have the option of rejecting any wash basin purporting to meet the requirements of this British Standard if it fails to meet any of the requirements laid down herein. Minor imperfections which do not affect the appearance or the efficiency of the articles shall not constitute valid reasons f

22、or rejection. 1.4 Manufacturers certificate The purchaser shall be entitled, on request, to a certificate testifying that the appliances comply with the provisions of this British Standard. 1.5 Marking Each article manufactured in accordance with this standard shall be clearly and indelibly marked s

23、o that it can be seen without dismantling the appliance with: 1) the manufacturers name or identification mark, 2) the number of this British Standard, i.e.BS 1188. NOTEThe mark BS1188 on or in relation to the product is a claim by the manufacturer that it complies with the requirements of this stan

24、dard. 1.6 Options The purchaser shall specify the following options: 1) material (see2.1); 2) colour (see3.6); 3) overflow (see3.7); 4) chain stay hole (see3.9); 5) type and size (see4.1 and Table 1). 2 Materials 2.1 General The wash basins and pedestals shall be made from either fireclay or vitreou

25、s china and the purchaser shall specify which material is required when ordering (see1.6). 2.2 Quality Each wash basin and pedestal shall be fired at such a temperature as to produce a satisfactorily fused ceramic glaze and as an article it shall be sound, of good workmanship and without manufacturi

26、ng faults affecting utility. The glaze shall be uniform, non-crazing, free from discoloration and shall possess an impervious surface. Preferably it shall be leadless but shall not, in any event, yield more than5% of soluble lead. Vitreous china wash basins and pedestals shall comply with the requir

27、ements of BS3402. 3 Design and construction 3.1 General The wash basins shall be of one piece construction. Any internal angles shall be designed to facilitate cleaning. 3.2 Tap holes There shall be two tap holes to each wash basin, round in shape and symmetrical about the centre line of the basin.

28、The level of the top of the platform which accommodates the taps shall not be below the spillover level of the basin irrespective of the overflow slot. 3.3 Pedestals Ceramic pedestals for wash basins shall comply with the following requirements: 1) they shall be recessed at the back to take supply a

29、nd waste pipes and fittings; 2) they shall rigidly and adequately support the wash basin; 3) the combined height of wash basin and pedestal shall be measured from top of rim at front of basin to the floor level.BS1188:1974 2 BSI 04-1999 3.4 Waste holes The recess of the outlet for the waste flange s

30、hall have a diameter of not less than64mm as shown in Figure 1so that it is suitable for a waste fitting having a flange of62mm diameter, and the hole through the ware shall have a minimum diameter of44mm. For vitreous china wash basins, the outlets shall be bevelled. For fireclay wash basins, the o

31、utlets shall be either bevelled or rebated. 3.5 Bracket studs Any provision to receive the brackets on the underside of the wash basin shall be capable of receiving a bracket stud not exceeding13mm diameter, 8mm high and305mm from the back of the basin to the centre of the stud. 3.6 Colour Wash basi

32、ns and pedestals shall be supplied in either white or any colour specified by the purchaser. NOTEUnless otherwise specified by the purchaser at the time of enquiry or order (see1.6) the basin and pedestal will be supplied in white. 3.7 Overflow Wash basins shall be supplied in either of the followin

33、g conditions: a) the basin shall not have an overflow hole; or b) the basin shall have an overflow with a horizontal dimension not longer than 64mm and an area of not less than800mm 2 , located completely below the spillover level of the basin. NOTEUnless otherwise specified by the purchaser at the

34、time of enquiry or order (see1.6) the basin will be supplied with an overflow hole. 3.8 Soap sinkings The soap sinking(s) shall be adequately drained into the bowl. The sinking(s) shall not be so placed as to drain across the width of the overflow slot. 3.9 Chain stay hole Wash basins shall be suppl

35、ied in either of the following conditions: a) the basin shall not have a chain stay hole; or b) the basin shall have a chain stay hole of8 1mm in diameter located as high as is practicable within the bowl. If an overflow is provided, the chain stay hole shall be located above the level of the top of

36、 the overflow. NOTEUnless otherwise specified by the purchaser at the time of enquiry or order (see1.6) the basin will be supplied with a chain stay hole. NOTEDrawings are diagrammatic only. Figure 1 Details of outletsBS1188:1974 BSI 04-1999 3 4 Types, dimensions, masses and permissible deviations 4

37、.1 Types The British Standard range shall include the following types and shall comply with the dimensions specified in Table 1 and Table 2 subject to the permissible deviations from the work size specified. Type A Wash basins with back skirting up to76mm high. Type B Wash basins without back skirti

38、ng. The purchaser shall specify the type and co-ordinating size required (see1.6). Table 1Dimensions and masses Table 2 Ancillary dimensions a Type Dimension Standard basic space (co-ordinating size) Max. limit of manufacturing size Work size (nominal size) Min. limit of manufacturing size Min. mass

39、 mm mm mm mm kg A(1) Length 700 650 635 620 18 Fireclay Width 500 465 455 445 15 Vitreous china A(2) Length 600 572 560 548 15 Fireclay Width 500 414 405 396 11.5 Vitreous china B(1) Length 700 650 635 620 17 Fireclay Width 500 465 455 445 13.5 Vitreous china B(2) Length 600 572 560 548 13 Fireclay

40、Width 500 414 405 396 10 Vitreous china Description Dimensions Type A(1) Type B(1) Wash basins mm Tap centres: distance apart 485 distance from back of basin 140 Bracket centres 585 Type A(2) Type B(2) Wash basins mm Tap centres: distance apart 405 distance from back of basin 140 Bracket centres 510

41、 Dimensions applicable to both types and sizes mm Combined height of wash basin and pedestal 800 Depth from top edge of rim to inside base of bowl at centre of outlet 165 Distance of centre of outlet from extreme back (for details of outlets, see Figure 1) 180 Maximum height of back skirting, if any

42、, above top rim of basin 76 Diameter of tap holes (not subject to the deviations permitted by the footnote to this table) NOTEFor level of tap platform, see3.2. Diameter of hole for chain stay 8 1 a Permissible deviations: for dimensions of 76mm and over, 2%; for dimensions of less than 76 mm, 5%. 3

43、02 +0 4 blankBS1188:1974 BSI 04-1999 Publication referred to This standard makes reference to the following British Standard: BS3402, Quality of vitreous china sanitary appliances. BS1188:1974 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national bod

44、y responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest a

45、mendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be

46、 found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publicatio

47、ns should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides

48、 a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:0208

49、9967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, st