BS 1574-1994 Specification for split pins (inch series)《开口销规范(英制系列)》.pdf

1、BRITISH STANDARD BS 1574:1994 Specification for Split pins (inch series)BS1574:1994 This British Standard, having been prepared under the directionof the General Mechanical Engineering Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15March

2、1994 BSI 03-1999 The following BSI references relate to the work on this standard: Committee reference GME/9 Draft for comment 90/73145 DC ISBN 0 580 22779 0 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the General Mechanical Engineering

3、Standards Policy Committee (GME/-) to Technical Committee GME/9, upon which the following bodies were represented: BEAMA Ltd. British Constructional Steelwork Association Ltd. British Industrial Fasteners Federation British Steel Industry British Steel Industry (Wire Section) Gauge and Tool Makers A

4、ssociation Society of Motor Manufacturers and Traders Ltd. Washer Manufacturers Association of Great Britain The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Defence Manufacturers Association General Municipal Boilermaker and Allied Trades

5、 Union Screw Thread Tool Manufacturers Association Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBS1574:1994 BSI 03-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Normative references 1 3 Dimensions 1 4 F

6、orm and tolerance 1 5 Characteristics 1 6 Designation 1 Figure 1 Dimensions of inch split pins 4 Table 1 Dimensions of inch split pins 2 Table 2 Lengths of inch split pins 3 Table 3 Tolerance on length of inch split pins 4 Table 4 Characteristics of inch split pins 5 List of references Inside back c

7、overBS1574:1994 ii BSI 03-1999 Foreword This British Standard has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee. It supersedes BS1574:1972, which is withdrawn. The principal changes that have been made in this edition are as follows. a) The deleti

8、on of metric sizes which are now specified in BS 7724:1994. b) The addition of the material characteristics for stainless steel, copper and brass from which inch series split pins may be manufactured. A British Standard does not purport to include all the necessary provisions of a contract. Users of

9、 British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to 6, an inside back cover and a back

10、cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.BS1574:1994 BSI 03-1999 1 1 Scope This British Standard specifies the characteristics of ferrous and non-ferrous split pins with

11、 inch dimensions and nominal diameter from 1 / 32inch to 1 / 2inch inclusive. 2 Normative references This British Standard incorporates, by reference, provisions from specific editions of other publications. These normative references are cited at the appropriate points in the text and the publicati

12、ons are listed on the inside back cover. Subsequent amendments to, or revisions of, any of these publications apply to this standard only when incorporated in it by updating or revision. 3 Dimensions The dimensions and tolerances of inch split pins shall be as given inTable 1 andTable 2 and Figure 1

13、. 4 Form and tolerance The tolerance of the split pin hole shall be H13, in accordance with BS4500-1.1:1990 and BS4500-1.2:1990. The eye of the pin shall approximate to the form shown inFigure 1. The length of the eye shall be the distance from the underside to the extreme outer surface of the eye a

14、nd shall conform to the dimensions given inTable 1. The closed legs of the shank shall form a circular cross section and be straight and parallel throughout the nominal length. The nominal length of pin shall be the distance of the eye to the extreme end of the short leg, i.e.the straight length of

15、the short leg (seeFigure 1). The tolerance on the length of inch split pins shall be as given inTable 3. 5 Characteristics The characteristics of inch split pins shall be as given inTable 4. 6 Designation When designating for the purposes of an enquiry or order, the following information shall be gi

16、ven: a) general product description, i.e.split pin; b) the number of this British Standard, i.e.BS1574:1994; c) the nominal diameter of the product in inches; d) the nominal length in inches; e) the material, i.e.stainless steel; f) details of the coating (if requested) and the relevant British Stan

17、dard, e.g.BS7371. Example: The designation of a steel split pin of nominal diameter 1 / 8 inch and nominal length1inch is as follows: BS1574:1994 1 / 8 1 steelBS1574:1994 2 BSI 03-1999 Table 1 Dimensions of inch split pins Dimensions in inches Nominal diameter ab d a R b c max. min. max. min. max. m

18、ax. c 1 / 32 3 / 64 1 / 16 5 / 64 3 / 32 ( 7 / 64 ) 1 / 8 ( 9 / 64 ) 5 / 32 ( 11 / 64 ) 3 / 16 ( 7 / 32 ) 1 / 4 ( 9 / 32 ) 5 / 16 3 / 8 ( 7 / 16 ) 1 / 2 0.031 0.046 0.062 0.077 0.093 0.108 0.124 0.140 0.155 0.171 0.186 0.218 0.249 0.280 0.311 0.373 0.436 0.498 0.024 0.035 0.051 0.067 0.083 0.101 0.1

19、06 0.132 0.138 0.161 0.173 0.208 0.224 0.270 0.287 0.358 0.421 0.476 0.06 0.10 0.10 0.10 0.10 0.10 0.10 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.25 0.25 0.25 0.03 0.05 0.05 0.05 0.05 0.05 0.05 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.12 0.12 0.12 0.002 0.004 0.006 0.006 0.008 0.008 0.010 0.011 0.0

20、12 0.013 0.016 0.016 0.020 0.021 0.024 0.028 0.033 0.038 0.09 0.11 0.12 0.16 0.19 0.22 0.25 0.28 0.31 0.34 0.38 0.44 0.50 0.56 0.62 0.75 0.87 1.00 0.062 0.092 0.124 0.154 0.186 0.216 0.248 0.280 0.310 0.342 0.372 0.436 0.498 0.560 0.622 0.746 0.872 0.996 a The nominal diameter is the diameter of the

21、 split pin hole. b The sizes shown in brackets are non-preferred. c No values are given in the table for the minimum eye diameter c but it shall not be less than 1.75 times the actual shank diameterd.BS1574:1994 BSI 03-1999 3 Table 2 Lengths of inch split pins Dimensions in inches Nominal length l N

22、ominal diameter a 1 / 32 3 / 64 1 / 16 5 / 64 3 / 32 ( 7 / 64 ) 1 / 8 ( 9 / 64 ) 5 / 32 ( 11 / 64 ) 3 / 16 ( 7 / 32 ) 1 / 4 ( 9 / 32 ) 5 / 16 3 / 8 ( 7 / 16 ) 1 / 2 1 / 4 3 / 8 1 / 2 5 / 8 3 / 4 7 / 8 1 1 1 / 8 1 1 / 4 Range of commerciallengths 1 3 / 8 1 1 / 2 1 5 / 8 1 3 / 4 1 7 / 8 2 2 1 / 4 2 1

23、/ 2 2 3 / 4 3 3 1 / 4 3 1 / 2 3 3 / 4 4 4 1 / 4 4 1 / 2 5 5 1 / 2 6 a The sizes shown in brackets are non-preferred.BS1574:1994 4 BSI 03-1999 Table 3 Tolerance on length of inch split pins NOTEFor dimension l see Table 2. Figure 1 Dimensions of inch split pins Dimensions in inches Nominal diameter T

24、olerance on length # 1 / 8 1 / 8# 1 / 4 1 / 4# 3 / 8 3 / 8 0.060 0.080 0.100 0.120BS1574:1994 BSI 03-1999 5 Table 4 Characteristics of inch split pins Material Ferrous Steel 0.15 % C max. Maximum UTS 620 N/mm 2 Stainless steel 0.15 % C max. 1.00 % Si max. 2.00 % Mn max. 0.045 % S max. 0.045 % P max.

25、 17/20 % Cr max. 7/11 % Ni max. Maximum UTS 620 N/mm 2 Non-ferrous Copper Hard condition for d # 1 / 4inch Annealed condition for d 1 / 4inch Brass 1 / 4hard condition for d # 3 / 8inch Annealed condition for d 3 / 8inch Surface finish Split pins shall be supplied in natural finish treated with a pr

26、otective lubricant, unless otherwise specified by agreement between customer and supplier. Workmanship Parts shall be uniform in quality and free of irregularities or detrimental defects. Acceptability The acceptance procedure is covered in BS 6587:1985.6 blankBS1574:1994 BSI 03-1999 List of referen

27、ces (see clause2) Normative references BSI publications BRITISH STANDARDS INSTITUTION, London BS 4500, ISO limits and fits. BS 4500-1, General tolerances and deviations. BS 4500-1.1:1990, Specification for bases of tolerances, deviations and fits. BS 4500-1.2:1990, Tables of commonly used tolerance

28、and grades and limits deviations for holes and shafts. BS 6587:1985, Method of acceptance inspection for fasteners. BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

29、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international l

30、evel. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be

31、 grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating

32、service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for

33、 international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and

34、its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developme

35、nts and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publicati

36、ons of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permissi

37、on from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.