BS 1595-1-1986 Propan-2-ol (isopropyl alcohol) for industrial use - Specification for propan-2-ol (isopropyl alcohol)《工业用2－丙醇（异丙醇） 第1部分 2－丙醇规范（异丙醇）》.pdf

1、BRITISH STANDARD BS 1595-1: 1986 Propan-2-ol (isopropyl alcohol) for industrial use Part 1: Specification for propan-2-ol (isopropyl alcohol) UDC 661.725.2:547.263BS1595-1:1986 This British Standard, having been prepared under the directionof the Chemicals Standards Committee, was published under th

2、e authority ofthe Board of BSI and comes intoeffect on 31October1986 BSI 08-1999 First published as BS1595 March1950 First revision March1957 Second revision June1965 (lateramended to Part1) Third revision as BS1595-1 October1986 The following BSI references relate to the work on this standard: Comm

3、ittee reference CIC/51 Draft for comment85/50953 DC ISBN 0 580 15362 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Chemicals Standards Committee (CIC/-) to Technical Committee CIC/51, upon which the following bodies were represented:

4、 British Pharmacopoeia Commission British Society of Perfumers Chemical Industries Association Department of Trade and Industry (Laboratory of the Government Chemist) Royal Society of Chemistry Amendments issued since publication Amd. No. Date of issue CommentsBS1595-1:1986 BSI 08-1999 i Contents Pa

5、ge Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Description 1 3 Sampling and size of sample 1 4 Colour 1 5 Density 1 6 Distillation range 1 7 Residue on evaporation 1 8 Miscibility with water 1 9 Water content 1 10 Alkalinity or acidity 1 11 Aldehydes and ketones 1 Publications

6、referred to Inside back coverBS1595-1:1986 ii BSI 08-1999 Foreword This Part of BS1595, which has been prepared under the direction of the Chemicals Standards Committee, comprises a specification for propan-2-ol (previously known as isopropyl alcohol) to meet the requirements of a wide range of indu

7、strial users. It does not, however, apply to material for medicinal use, requirements for which are included in the British Pharmacopoeia, or to material sold as “isopropyl alcohol azeotrope”. First published in1950, BS1595 was last revised in1965 and was subsequently amended to become BS1595-1. In

8、the present edition of BS1595-1, a requirement for colour has been introduced and the requirement for relative density has been replaced by one for density at20 C. In addition, the test methods associated with the specification are now published separately as BS1595-2. This standard supersedes BS159

9、5-1:1965, which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of

10、pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cov

11、er.BS1595-1:1986 BSI 08-1999 1 1 Scope This British Standard specifies requirements for propan-2-ol suitable for industrial purposes. It does not apply to material for medicinal use or to material sold as “isopropyl alcohol azeotrope”. NOTEThe titles of the publications referred to in this standard

12、are listed on the inside back page. 2 Description The material shall be clear and free from matter in suspension, as assessed by visual inspection, and shall consist essentially of propan-2-ol (CH 3 ) 2 CHOH. 3 Sampling and size of sample A sample of not less than 1 L shall be taken in accordance wi

13、th BS1595-2. 4 Colour The colour of the material shall not exceed15 Hazen units when measured as described in BS5339. 5 Density The density of the material at20 C shall be notlower than0.785g/mL and not higher than0.787g/mL when determined as described in BS4522. 6 Distillation range When the materi

14、al is distilled as described in BS4591, modified as specified in BS1595-2, the initial boiling point at1013 mbar 1)pressure shall benot lower than81.5 C and the dry point at1013mbar pressure shall be not higher than83.0 C. 7 Residue on evaporation The residue on evaporation of the material shall not

15、 exceed0.002% (m/m) when determined as described in BS4524. 8 Miscibility with water The material shall not show opalescence when tested as described in BS1595-2. 9 Water content The material shall not contain more than0.50%(m/m) of water when determined as described in clause3 of BS2511:1970, using

16、20mL of the material. 10 Alkalinity or acidity The material shall not be alkaline to phenolphthalein and shall not contain more than0.002% (m/m) of acid, calculated as acetic acid (CH 3 COOH) and determined as described in BS1595-2. 11 Aldehydes and ketones The material shall not contain more than0.

17、10% (m/m) of aldehydes and ketones, calculated as acetone (CH 3 COCH 3 ) and determined as described in BS1595-2. 1) 1mbar =100N/m 2 =100Pa.2 blankBS1595-1:1986 BSI 08-1999 Publications referred to BS 1595, Propan-2-ol (isopropyl alcohol) for industrial use. BS 1595-2, Methods of test. BS 2511, Meth

18、ods for the determination of water (Karl Fischer method). BS 4522, Method for the determination of density of liquids at20 C. BS 4524, Method for determination of residue on evaporation on a water bath. BS 4591, Method for the determination of distillation characteristics. BS 5339, Method of measure

19、ment of colour in Hazen units (platinum-cobalt scale) of liquid chemical products. BS 1595-1: 1986 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe a

20、nd at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products an

21、d services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an indi

22、vidual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to

23、orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Lib

24、rary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards develo

25、pments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications

26、 of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission f

27、rom BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.