ImageVerifierCode 换一换
格式:PDF , 页数:8 ,大小:243.26KB ,
资源ID:543257      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-543257.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS 2782-4 Method 432D-1995 Methods of testing plastics - Chemical properties - Determination of styrene evaporation from unsaturated polyester resins《塑料试验方法 第4部分 化学性能 试验方法432D 不饱和聚.pdf)为本站会员(dealItalian200)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

BS 2782-4 Method 432D-1995 Methods of testing plastics - Chemical properties - Determination of styrene evaporation from unsaturated polyester resins《塑料试验方法 第4部分 化学性能 试验方法432D 不饱和聚.pdf

1、BRITISH STANDARD BS 2782-4: Method 432D: 1995 Methods of testing Plastics Part 4: Chemical properties Method 432D: Determination of styrene evaporation from unsaturated polyester resinsBS2782-4:Method 432D:1995 This British Standard, having been prepared under the directionof the Sector Board forMat

2、erials and Chemicals, waspublished under the authorityof the Standards Boardand comes into effect on 15 August 1995 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference PRI/40 Draft for comment 93/314379DC ISBN 0 580 24238 2 Committees responsible for thi

3、s British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/40, Thermosetting resins, prepregs and moulding compounds, upon which the following bodies were represented: BEAMA Ltd. British Plastics Federation Chemical Industries Association Electrical Installa

4、tion Equipment Manufacturers Association (BEAMA Ltd.) European Resin Manufacturers Association Ministry of Defence RAPRA Technology Ltd. Amendments issued since publication Amd. No. Date CommentsBS2782-4:Method 432D:1995 BSI 11-1999 i Contents Page Committees responsible Inside front cover Foreword

5、ii 1 Scope 1 2 Normative references 1 3 Principle 1 4 Apparatus and materials 1 5 Procedure 2 6 Test report 2 Figure 1 Apparatus showing shielding 1 List of references Inside back coverBS2782-4:Method 432D:1995 ii BSI 11-1999 Foreword This British Standard has been prepared by Technical Committee PR

6、I/40. It is based on a method originally published by the British Plastics Federation. A related method is BS 2782:Method 432:1991 Determination of residual styrene monomer content in reinforced plastics based on polyester resins. WARNING NOTE. This British Standard method does not necessarily detai

7、l all the precautions necessary to meet the requirements of the Health and Safety at work, etc. Act 1974. Attention should be paid to any appropriate safety precautions and the method should be operated only be trained personnel. A British Standard does not purport to include all the necessary provi

8、sions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2, an

9、 inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS2782-4:Method 432D:1995 BSI 11-1999 1 1 Scope This British Standard describes a method for meas

10、uring the rate of loss of styrene from contact moulded materials using unsaturated polyester resins and glass fibre chopped strand mats, with a surface open to the atmosphere. 2 Normative reference This British Standard incorporates, by reference, provisions from a specific edition of another public

11、ation. This normative reference is cited at the appropriate point in the text and the publication is listed on the inside back cover. Subsequent amendments to, or revisions of, this publication apply to this British Standard only when incorporated in it by updating or revision. 3 Principle A single

12、layer of reinforcement is impregnated with resin and supported on a top pan balance in a temperature-controlled room. The loss in mass in g/m 2is recorded graphically against time. 4 Apparatus and materials 4.1 Top pan balance, direct reading, accurate to0.01g. 4.2 Polyethylene terephthalate film 4.

13、3 Glass fibre chopped strand mat, emulsion bound, mass per unit area 450 g/m 2 , in accordance with BS3496. 4.4 Glass beaker, or other wax-free container. 4.5 Support platen, of nominal size 300 mm 300 mm. 4.6 Shielding for apparatus to prevent draughts, in accordance with Figure 1. 4.7 Clock or lab

14、oratory timing device, with an accuracy 1 s. 4.8 Quantity of test resin, having a mass not less than four times the mass of the chopped strand mat (see clause 5). 4.9 Catalyst and/or accelerator, when required (seeclause 5). Figure 1 Apparatus, showing shielding BS2782-4:Method 432D:1995 2 BSI 11-19

15、99 5 Procedure Carry out the test in a room of at least 50 m 3 , with the temperature controlled at 23 C 2 C. Assemble the balance and support platen in accordance with Figure 1. Position the shielding required. NOTEIf the apparatus is assembled in a draught-free room then the shielding is not essen

16、tial. Cut three pieces of glass fibre chopped strand mat of nominal dimensions 250 mm 250 mm and weigh each. Cut three pieces of polyethylene terephthalate film of nominal dimensions 300 mm 300 mm. Mark an area of 250 mm 250 mm on the back of the film with a marking pen. Tape the film, with marked s

17、ide downwards, on to the support platen. Adjust the polyester resin temperature in the glass beaker to 23 C 2 C. If a catalyst is used, catalyse and, if necessary, accelerate the resin and immediately start the clock. Stir the resin for 30 s, then pour a weighed quantity of resin from the glass beak

18、er on to the film, spreading evenly over the marked area. The quantity of resin used is calculated from the mass of the glass fibre chopped strand mat and shall be 2.5 times that mass. Place the piece of mat into the resin and quickly ensure complete impregnation of the mat by gently pressing with t

19、he edge of a spatula. Ensure that there is no free resin beyond the edge of the glass mat. After no more than 2 min, place the assembly consisting of support platen, film and impregnated mat on the top pan balance. Record the initial mass, and the mass after2min,5min, 10 min and then at 10 min inter

20、vals for a total time of 60 min. Longer times may be used by agreement and shall be reported. From the results plot a graph of mean cumulative loss in mass against time. Repeat the procedure for a total of three test assemblies. 6 Test report The test report shall include the following information:

21、a) the name of the testing establishment; b) the date of the test; c) complete identification of the materials tested, resin and glass fibre chopped strand mat, their type, source, manufacturers reference; d) a reference to this British Standard, i.e.determined in accordance with BS2782:Method 432D:

22、1994; e) the atmospheric pressure, temperature and relative humidity at the time of testing; f) the amount of styrene emitted, expressed as mass per unit area of the test piece, (g/m 2 ) after60 min, and a graphical representation of its emission, for each of the three samples tested; g) if a cataly

23、st is used, specify catalyst type and quantity; h) type and quantity of accelerator if used.BS2782-4:Method 432D:1995 BSI 11-1999 List of references (see clause 2) Normative reference BSI publication BRITISH STANDARDS INSTITUTION, London BS 3496:1989, Specification for E glass fibre chopped strand m

24、at for reinforcement of polyester and other liquid laminating systems. BS 2782-4: Method 432D: 1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe

25、and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products a

26、nd services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an ind

27、ividual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to

28、 orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Li

29、brary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards devel

30、opments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publication

31、s of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission

32、 from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1