BS 2S 514-1969 Specification for carbon-manganese steel sheet and strip (for use in the hardened and tempered condition 770 1000 MPa) (suitable for welding)《碳锰钢薄板和带材规范(淬火和回火条件 77 1.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS 2S 514:1969 (Superseding BS S 514) Incorporating Amendment No. 1 Specification for carbon-manganese steel sheet and strip (for use in the hardened and tempered condition: 770/1 000 MPa) (suitable for welding) UDC 669.1574 194 41 This Standard is obsolescent. See

2、the BSI Catalogue for detailsBS 2S 514:1969 This British Standard, having been approved by the Aerospace Industry Standards Committee, was published under the authority of the Executive Board of the Institution on 24 February 1969 BSI 30 May 2003 The following references relate to the work on this s

3、tandard: Committee reference ACE/15 Draft for comment 67/13801 ISBN 0 580 05236 2 Amendments issued since publication Amd. No. Date Comments 14155 30 May 2003 Indicated by a sidelineBS 2S 514:1969 BSI 30 May 2003 i Contents Page Foreword ii 1 Inspection and testing procedure 1 2 Process of manufactu

4、re 1 3 Chemical composition 1 4 Surface dressing 1 5 Condition 1 6 Final heat treatment 2 7 Mechanical properties 2BS 2S 514:1969 ii BSI 30 May 2003 Foreword This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Co

5、mpliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicat

6、es when the document was last issued. Sidelining in this document indicates the most recent changes by amendment.BS 2S 514:1969 BSI 30 May 2003 1 NOTE Sheet and strip of the same composition for use in the softened condition are covered by the latest edition of BS S 515. 1 Inspection and testing pro

7、cedure 1.1 This British Standard shall be used in conjunction with the relevant sections of the latest edition of BS S 500. 1.2 The thickness of the material shall be in accordance with the latest edition of BS S 500. Material which has been finally hot-rolled prior to softening or hardening and tem

8、pering shall satisfy the tolerances applicable to hot-rolled steel sheet or strip (excluding mild steel). Material which has been finally cold-rolled prior to softening or hardening and tempering shall satisfy the tolerances applicable to cold-rolled steel sheet and strip (excluding mild steel). 1.3

9、 Sulphur printing or deep etching tests. Samples shall be selected in accordance with the latest edition of BS S 500. 2 Process of manufacture The material shall be manufactured by an oxygen, open hearth or electric process, unless otherwise agreed between the manufacturer and the purchaser in accor

10、dance with the latest edition of BS S 500. 3 Chemical composition The steel shall contain: 4 Surface dressing The material shall be locally dressed in accordance with the requirements of the latest edition of BS S 500. 5 Condition 5.1 The material shall be supplied in one of the following conditions

11、 after final hot or cold rolling. 1) Softened. 2) Hardened and tempered. 5.2 The condition required shall be stated on the order. Unless otherwise agreed the method of rolling shall be at the option of the manufacturer but shall be stated in the release note. 5.3 Finished parts shall be supplied fin

12、ally heat treated. Element % min. max. Carbon 0.17 0.25 Silicon 0.10 0.35 Manganese 1.3 1.7 Phosphorus 0.040 Sulphur 0.040 Chromium 0.25 Molybdenum 0.10 Nickel 0.40BS 2S 514:1969 2 BSI 30 May 2003 6 Final heat treatment The final heat treatment shall be as follows. 1) Harden in oil or water from a t

13、emperature between 860 C and 880 C. 2) Temper at a temperature of not less than 500 C. 7 Mechanical properties 7.1 Tests in the softened condition 1) Hardness. The hardness of the material shall be not more than 179 HB or 190 HV. 2) Single bend test. The test piece shall be bent without cracking thr

14、ough an angle of 180 over a former with a radius equal to half the nominal thickness of the sheet or strip. 7.2 Tests in the hardened and tempered condition 1) Tensile test. The mechanical properties obtained from test pieces selected and prepared in accordance with the relevant requirements of the

15、latest edition of BS S 500 shall comply with the following table. The values in hectobars are to be regarded as the standard. 2) Hardness test for finally heat treated parts. The hardness of the material shall be: 229 min./302 max. HB; or 240 min./315 max. HV. 0.2 % proof stress Tensile strength Elo

16、ngation on thickness Less than 1.6 mm 1.6 to 2.4 mm Over 2.4 mm MPa MPa % % % min. min. max. min. min. min. 630 770 1 000 8 10 12blankBS 2S 514:1969 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Stand

17、ards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the const

18、ant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel

19、: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addres

20、sed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published

21、 as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which

22、 give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For de

23、tails of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is availa

24、ble on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced

25、, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type

26、or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.