ImageVerifierCode 换一换
格式:PDF , 页数:14 ,大小:610.59KB ,
资源ID:543490      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-543490.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS 2SP 7-1943 Specification for aircraft material - Fork joints (high tensile type) (for sizes No 4 B A to 3 4 inch B S F inclusive)《飞机材料规范 叉形接头(高强度型)(尺寸号 4B A 至英寸B S F》.pdf)为本站会员(ideacase155)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

BS 2SP 7-1943 Specification for aircraft material - Fork joints (high tensile type) (for sizes No 4 B A to 3 4 inch B S F inclusive)《飞机材料规范 叉形接头(高强度型)(尺寸号 4B A 至英寸B S F》.pdf

1、BRITISH STANDARD CONFIRMED APRIL1998 BS 2SP 7: 1943 (CancellingBS Specification BSSP7.) Incorporating Amendment Nos. 1, 2, 3 and 4 Specification for Aircraft Material Fork Joints (HighTensile Type) (ForSizes No. 4 B.A. to 3 / 4 inch B.S.F.inclusive) NOTEThe Institution desires to call attention to t

2、he fact that this Specification is intended to include the technical provisions necessary for the supply of the articles herein referred to, but does not purport to comprise all the necessary provisions of a contract.BS2SP7:1943 This Specification having been approved by the Aircraft IndustryCommitt

3、ee was published by the authority of theCouncil of the Institution asaBritish Standard on 19February 1943 BSI 05-2000 ISBN058034446 0 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. C

4、ompliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 8 and a back cover. This standard has been updated (see copyright date) and may have had amendments i

5、ncorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date Comments 629 May 1947 2714 February 1957 4084 February 1961 6220 July 1967 Indicated by a sideline in the marginBS2SP7:1943 BSI 05-2000 i Contents Page 1 Manufactur

6、e 1 2 Screw threads 1 3 Anti-corrosion treatment 1 4 Selection for testing 1 5 Mechanical test 1 6 Marking 1 7 Material 1 8 Manufacture 1 9 Design and dimensions 1 10 Material 1 11 Manufacture 2 12 Design and dimensions 2 13 Freedom from defects 2 14 Heat treatment 2 15 Selection and preparation of

7、mechanical test samples 2 16 Mechanical tests 2 17 Hardness tests 3 18 Magnetic crack detection 3 Table 1 Fork Joints (High Tensile Type) 4 Table 2 Fork Joints (High Tensile Type) 6 Table 3 Fork Joints (High Tensile Type) 7 Table 4 Fork Joints (High Tensile Type) 8ii blankBS2SP7:1943 BSI 05-2000 1 N

8、OTEThe order must state the material classification letter and part number of the fork joints required in accordance with Clause5. 1 Manufacture Fork joints may, at the option of the manufacturer, be made by machining either from bar or from blanks produced by the “cold heading” process. Theyshall b

9、e tapped either right hand or left hand as specified on the order. 2 Screw threads The screw threads of coated fork joints in non-corrosion resisting steel and those of fork joints in corrosion resisting steel shall not be smaller than the minimum full, effective and core diameters specified in Tabl

10、e III of BS Specification No.93 forBritish Association Threads, or Table12of BSSpecification No.84 for British Standard Fine Threads. The screw threads of all fork joints (thosein non-corrosion resisting steel after being coated) shall be required to pass approved gauges. 3 Anti-corrosion treatment

11、All parts in non-corrosion resisting steel shall be uniformly coated with cadmium in accordance with the requirements of specification DTD904 1) . 4 Selection for testing Samples of fork joints may be selected at the discretion of the Inspector and tested as specified inClause5. 5 Mechanical test Th

12、e finished fork joints selected as specified in Clause4 shall be screwed on to the wire as far as theinspection hole in the case of sizes up to and including 1 / 2in. and as far as the commencement of the gap in the case of sizes 9 / 16in. and over, and the axial load shall be applied to a pin place

13、d through the holes in the fork joints, no part of the fork joint being gripped in the testing machine. When loaded in this manner the fork joints shall show an ultimate strength not less than that given in Table 1 (Col.25) Table 2 (Col.23) Table 3 (Col.25) and Table 4 (Col.24). 6 Marking All fork j

14、oints shall have the appropriate part number applied on the shank near the tapped endby rolling and shall also bear the mark of the Inspector. If made of stainless steel they shall in addition be marked with the letter “Z” preceding thepart number. NOTEFor ordering purposes a letter “Y” shall be ins

15、erted in the Part Reference Number for non-corrosion resisting fork joints between the Specification Number and Part Number so as to distinguish clearly between non-corrosion resisting and corrosion resisting parts. For example, the complete Part Reference Number for 5 / 16in. non-corrosion resistin

16、g fork joint (left-hand thread) is BS SP7 Y/GL and for corrosion resisting steel BSSP7Z/GL, while the corresponding markings on the actual fork joint will be GL and Z/GL. FORK JOINTS MACHINED FROM BAR 7 Material Fork joints machined from bar shall be made from steel bars which have been inspected an

17、d passed bythe Inspector as complying with the latest issue of BS Specification BSS94, BSS96, BSS114 orBSS117 (B.) or BS Specification BSS80 where corrosion resisting steel is specified. 8 Manufacture Fork joints shall be machined bright all over. 9 Design and dimensions All fork joints (those in no

18、n-corrosion resisting steelafter coating) shall be in accordance with thedimensions and limits given inTable 1 and Table 2orTable 3 andTable 4, with the exception that those made in stainless steel shall have the collar (D) and projection (W) omitted. FORK JOINTS MADE BY THE “COLD HEADING” PROCESS (

19、for SIZES 4 B.A. to 13 / 32 in. ONLY). 10 Material a) The fork joints shall be machined from blanks made from steel of the following chemical compositions 2) : 1) Ministry of Technology, Process Specification DTD904 for cadmium plating. Carbon not less than 0.30 nor morethan0.45 per cent. Silicon no

20、t less than 0.10 nor morethan0.35 per cent. Manganese not more than 1.50 per cent. 2) Steel of this composition is covered by BS970 En. 8.BS2SP7:1943 2 BSI 05-2000 b) The complete analysis of every cast shall be supplied to the Inspector. c) When corrosion resisting steel fork joints are required, t

21、he steel shall comply with the chemical composition of BSS80. 3) 11 Manufacture The blanks shall be made by an approved process from material in a suitably softened condition. 12 Design and dimensions All fork joints (those in non-corrosion resisting steelafter coating) shall be in accordance with t

22、he dimensions and limits given inTable 3 andTable 4, with the exception that those made in corrosion resisting steel shall have the projection (W) omitted. 13 Freedom from defects a) The fork joints shall be free from defects. b) Any fork joint may be rejected at any time forfaults in manufacture no

23、twithstanding that ithas been passed previously on chemical composition and mechanical tests. 14 Heat treatment a) All blanks before machining shall be hardened and tempered to the required ultimate strength. b) No blanks shall be re-hardened more than three times. 15 Selection and preparation of me

24、chanical test samples a) Blanks hardened and tempered by a continuous process. During each period of continuous heat treatment not exceeding8hours, at least one test sample shall be selected. This test sample shall be either one of the blanks of the largest diameter that has been treated during this

25、 period or a length of wire from which these blanks have been made, and which has been hardened and tempered with the blanks represented. The test pieces machined from the selected blanks or lengths of wire in accordance with Clause16 c) shall comply with the mechanical test requirements ofClause16.

26、 b) Blanks hardened by a continuous process or in batches and tempered in batches comprising one tempering furnace charge. Sufficient test samples shall be hardened with the blanks to enable at least one test sample to be tempered with each batch. This test sample may be either one blank of the larg

27、est diameter from the tempered batch or a length of wire from which the largest blanks in the tempered batch have been made. The test pieces machined fromthe selected blanks or lengths of wire in accordance with Clause16 c) shall comply with the mechanical test requirements of Clause16. c) If any te

28、st piece fails to meet the mechanical tests, two further samples selected as in paragraph a) or b) above shall be submitted to the mechanical tests specified in Clause16. If either of these test pieces fails to meet the mechanical tests specified the blanks represented may be rejected or, at the req

29、uest of the manufacturer, be re-heat treated and re-tested in accordance with Clause8. 16 Mechanical tests a) All tests shall be carried out to the satisfaction of the Inspector. b) The mechanical properties of the material shall be as follows: c) Tensile test. The tensile test pieces shall be machi

30、ned from the selected samples to the dimensions of the largest possible size of theBritish Standard tensile test piece Figures1,2,3or4of British Standard Specification No.2A4. Alternatively, at the option of the manufacturer the tensile test maybe made on the full cross section of the unmachined tes

31、t sample. d) i) Izod test. The Izod test pieces shall be machined from the selected samples to the dimensions of the British Standard notched bar test piece Figure7or10 of British Standard Specification No.2A4 and tested ina 120 ft. lb. Izod machine. ii) When the dimensions of a test sample are such

32、 that neither of the British Standard notched bar test pieces can be made from it, the nicked fracture test see paragraph e) shallbe substituted for the Izod test. Sulphur not more than 0.06 per cent. Phosphorus not more than 0.06 per cent. 3) Steel with chemical composition of BSS 80 is covered by

33、BS970 En. 57. Ultimate Tensile Stress Not less than 55 and not more than 65 tons per sq. in. Elongation on4 Not less than 15 per cent. Izod Not less than 40 ft. lb. Nicked fracture See paragraph e) below. ABS2SP7:1943 BSI 05-2000 3 e) Nicked fracture test. A test piece, nicked orsawn so that the are

34、a of the portion to be fractured is not less than one-half of the original sectional area, must be free from defects when broken by a minimum number of blows. 17 Hardness tests Hardness tests shall be carried out by an approved method on representative hardened and tempered blanks selected by the In

35、spector. When continuous tempering is employed the blanks shall be selected for hardness tests at regular intervals and when tempered in batches the blanks shall be selected from each tempered batch. The hardness numbers obtained must be not less than248and not more than302on the Brinell Scale or th

36、eir equivalent values on the scale of themethod adopted. 18 Magnetic crack detection Each blank shall be subjected to an examination by means of an electro-magnetic crack detector of a type approved by the Deputy Director General of Aeronautical Inspection and shall be thoroughly inspected to verify

37、 freedom from cracks.BS 2 SP 7:1943 4 BSI 05-2000 Table 1 Fork Joints (High Tensile Type) (No.4 B.A. to 1 / 2in. B.S.F. inclusive) NOTEThe centre of the pinhole A and the centre line of the slot P must be within 0.010 inch of the centre lineoftheFork Joint. The Inspection Hole H must be drilled at r

38、ight angles to the axis of the Fork Joint at thespecifieddistance M from the end of the shank. Its actual position on the circumference of the shank may be determined by convenience of manufacture. Sketch showing Fork Joint with collar D omitted as manufacturing mark for Fork Joints made in corrosio

39、n resisting Steel.BS 2 SP 7:1943 BSI 05-2000 5 Table 1 Fork Joints (High Tensile Type) (No.4 B.A. to 1 / 2in. B.S.F. inclusive) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Part No. (See Footnote) Size of ForkJoint. A B C D E F G H J K L M N P Q R S T U V X Y Minimum Ultim

40、ate Tensile Strength. Approx. Weight. a Part No. of Standard Pin. (see latest issue of BS Specification BS SP 4.) Rt. Hd. Thd. Lt. Hd. Thd. + .001 + .005 0 + .01 0 + .01 0 + .015 0 + .015 0 + .015 0 + .04 0 + .015 0 + .04 0 + .04 0 + .015 0 + .01 0 + .01 0 + .01 0 + .04 Right Hand orLeft Hand Thread

41、. Pin Drill Rad. a 0 + .01 .01 + .01 in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in lb. lb. B BL 4 B.A. 5 / 32 5 / 32 .24 .07 .28 .05 .36 1 / 16 .33 .30 .21 .31 .25 .07 .03 .18 .18 1.20 4 B.A. .24 .20 .05 1,155 .010 A 2 C CL 2” 3 / 16 3 / 16 .29 .08 .33 .05 .44 1 / 16 .38

42、 .35 .24 .34 .30 .10 .04 .22 .22 1.30 2” .28 .25 .05 2,090 .015 B 3 D DL b 7 / 32 in. B.S.F. 7 / 32 15 / 64 .35 .10 .40 .05 .48 1 / 16 .48 .45 .29 .39 .36 .11 .07 .24 .26 1.44 7 / 32 in. B.S.F. .32 .29 .07 2,860 .030 C 4 E EL 1 / 4 ” 1 / 4 17 / 64 .39 .11 .45 .05 .56 1 / 16 .55 .50 .33 .43 .41 .125

43、.08 .28 .30 1.53 1 / 4 ” .37 .33 .08 3,795 .045 D 5 F FL b 9 / 32 ” 9 / 32 19 / 64 .44 .12 .50 .05 .60 1 / 16 .60 .55 .36 .46 .46 .14 .11 .30 .34 1.63 9 / 32 ” .41 .38 .08 5,115 .065 E 6 G GL 5 / 16 ” 11 / 32 21 / 64 .48 .12 .55 .05 .70 1 / 16 .70 .65 .40 .50 .50 .14 .12 .35 .40 1.74 5 / 16 ” .49 .4

44、2 .09 6,270 .095 G 7 H HL b 11 / 32 ” 11 / 32 23 / 64 .53 .15 .60 .05 .70 1 / 16 .75 .65 .45 .55 .55 .17 .17 .35 .43 1.80 11 / 32 ” .51 .45 .10 7,865 .110 G 8 J JL 3 / 8 ” 13 / 32 25 / 64 .59 .15 .67 .05 .82 1 / 16 .87 .75 .48 .58 .60 .17 .17 .41 .48 1.95 3 / 8 ” .57 .51 .10 9,350 .140 J 9 K KL b 13

45、 / 32 ” 7 / 16 27 / 64 .63 .15 .71 .05 .88 1 / 16 .97 .85 .51 .61 .63 .188 .20 .44 .55 2.07 13 / 32 ” .63 .55 .10 11,275 .160 K 9 L LL 7 / 16 ” 15 / 32 29 / 64 .68 .15 .76 .05 .92 1 / 16 1.05 .90 .54 .64 .68 .188 .23 .46 .59 2.15 7 / 16 ” .69 .60 .10 12,980 .195 L 10 M ML b 15 / 32 ” 1 / 2 31 / 64 .

46、72 .15 .80 .05 .98 1 / 16 1.10 .95 .57 .67 .72 .219 .26 .49 .64 2.22 15 / 32 ” .73 .64 .10 15,180 .230 M 11 N NL 1 / 2 ” 17 / 32 33 / 64 .77 .15 .85 .05 1.06 1 / 16 1.20 1.05 .60 .70 .77 .25 .26 .53 .67 2.35 1 / 2 ” .78 .69 .10 17,050 .270 N 13 NOTEWhere Fork Joints are manufactured in corrosion res

47、isting Steel (S 80) the Part Numbers must bear the prefix letter “Z” e.g., Z/D, Z/DL. a The figures in Cols. 22 and 26 are given for the information of designers and not for purposes of inspection. b These sizes are obsolescent and must not be used for new designs.BS 2 SP 7:1943 6 BSI 05-2000 Table

48、2 Fork Joints (High Tensile Type) 9 / 16 in. to 3 / 4in. B.S.F. inclusive NOTESThe centre of the pinhole A and the centre line of the slot P must be within 0.010 inch of the centre line of the Fork Joint. Sketch showing Fork Joint with collar D omitted as manufacturing mark for ForkJoints made in co

49、rrosion resisting Steel. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Part No. (See Footnote) Size of ForkJoint. A B C D E F G L N P Q R S T U V W X Y Z Minimum Ultimate Tensile Strength. Approx. Weight. a Part No. of Standard Pin. (see latest issueof BS Specification BSSP 4.) Rt. Hd. Thd. Lt. Hd. Thd. + .001 + .005 .005 0 + .015 0 + .015 0 + .015 0 + .02 0 + .04 0 + .015 0 + .01 0 + .01 0 + .01 0 + .04 Right-Hand or Left-Hand Thread. Pin

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1