BS 2SP 95-1974 Specification for elastomeric grommets (polychloroprene) for aerospace use《航空航天用弹性保护垫圈(氯丁橡胶)规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIES CONFIRMED APRIL 1998 BS 2SP 95: 1974 Incorporating Amendment No. 1 Specification for Elastomeric grommets (polychloroprene) for aerospace use UDC 629.7:62 761 477:678.763.2:678.074BS2SP 95:1974 This British Standard having beenapproved by the AerospaceIndustry Stand

2、ards Committee, was published underthe authority of the Executive Board on 31 December 1974 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for approval 73/32570 ISBN 0 580 08499 X Amendments issued since publication Amd. No. Date of iss

3、ue Comments 3515 February 1981 Indicated by a sideline in the marginBS2SP 95:1974 BSI 01-2000 i Contents Page Foreword ii 1 Scope 1 2 References 1 3 Material 1 4 Dimensions 1 5 Finish 1 6 Identification and packaging 1 7 Inspection and life control in stores 1 8 Example of call up 3 Figure 1 Grommet

4、 2 Table 1 Dimensions and part numbers 2 Table 2 Tolerances 3BS2SP 95:1974 ii BSI 01-2000 Foreword This British Standard has been prepared at the request of the Aerospace Industry to provide a range of grommets manufactured from polychloroprene (neoprene) rubber complying with BS 2752, grade C60. Th

5、e dimensional requirements of this standard are identical with those of BS 1767:1951 1) For grommets manufactured from other elastomeric materials refer also to BSSP93 “Elastomeric grommets acrylonitrile-butadiene” and to AS 44404, AS44405 and AS 44406 (Elastomeric grommets various) (SBAC series). A

6、 British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a

7、 front cover, an inside front cover, pages i and ii, pages1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. 1) The range of BS 1767 is slightly greater than t

8、hat of this standard.BS2SP 95:1974 BSI 01-2000 1 1 Scope This British Standard specifies the requirements relating to material, dimensions, finish, packaging, identification and storage inspection of elastomeric grommets with good resistance to ozone and some resistance to splash attack by aircraft

9、oils and fuels for operating temperatures up to 90 C, with peaks above this maximum. 2 References This standard makes reference to the following British Standards: BS 1916, Limits and fits for engineering Part1:Limits and tolerances. BS 2752, Polychloroprene rubber. BS F 68, The storage and inspecti

10、on in store of vulcanized rubber items. BS F 69, Packaging and identification of vulcanized rubber items. 3 Material The material shall comply with the requirements specified in BS 2752, grade C60 (Hardness 60 + 5, 4 IRHD). NOTEAlternatively, the grommets may be manufactured from material complying

11、with M.O.D. Specification DTD 5514, gradeD. 4 Dimensions 4.1 The grommets shall conform to the dimensions shown in Table 1 within the tolerances shown in Table 2. 4.2 The diameters of the panel holes into which the grommets are fitted should be equal to dimension W shown in Table 1, with H12 toleran

12、ces in accordance with BS 1916 NOTEThe dimensions in Table 1 are identical with those of BS1767 2) , BS SP 93, SBAC series AS 44404, AS 44405 and AS44406. 5 Finish 5.1 All flash and spew shall be removed by the manufacturer. 5.2 The surfaces shall be free from imperfections such as blisters and exce

13、ssive porosity and bloom. 6 Identification and packaging The grommets shall be identified and packaged to the requirements specified in BS F 69. 7 Inspection and life control in stores When required, and unless otherwise controlled, the inspection and stores lifting shall be in accordance with BS F

14、68. 2) The range of BS 1767 is slightly greater than that of this standard.BS2SP 95:1974 2 BSI 01-2000 Table 1 Dimensions and part numbers Figure 1 Grommet Dimensions in inches V W X Y Z 0.04 0.07 0.10 0.15 0.20 0.25 PART NUMBERS 1 / 16 1 / 8 3 / 16 3 / 16 1 / 4 5 / 16 0.313 0.375 0.438 0.094 0.094

15、0.094 A02 A04 A06 B02 B04 B06 C04 C06 D04 D06 E04 E06 F04 F06 1 / 4 5 / 16 3 / 8 3 / 8 7 / 16 1 / 2 0.500 0.625 0.688 0.094 0.125 0.125 A08 A10 A12 B08 B10 B12 C08 C10 C12 D08 D10 D12 E08 E10 E12 F08 F10 F12 7 / 16 1 / 2 9 / 16 5 / 8 11 / 16 3 / 4 0.813 0.875 1.000 0.125 0.125 0.125 A14 A16 A18 B14

16、B16 B18 C14 C16 C18 D14 D16 D18 E14 E16 E18 F14 F16 F18 5 / 8 11 / 16 3 / 4 13 / 16 15 / 16 1 1.063 1.188 1.250 0.125 0.125 0.125 A20 A22 A24 B20 B22 B24 C20 C22 C24 D20 D22 D24 E20 E22 E24 F20 F22 F24 7 / 8 1 1 1 / 8 1 1 / 8 1 1 / 4 1 3 / 8 1.438 1.563 1.688 0.156 0.156 0.156 A28 A32 A36 B28 B32 B3

17、6 C28 C32 C36 D28 D32 D36 E28 E32 E36 F28 F32 F36 1 1 / 4 1 3 / 8 1 1 / 2 1 1 / 2 1 5 / 8 1 3 / 4 1.813 1.938 2.125 0.156 0.156 0.188 A40 A44 A48 B40 B44 B48 C40 C44 C48 D40 D44 D48 E40 E44 E48 F40 F44 F48 1 3 / 4 2 2 2 1 / 4 2.375 2.625 0.188 0.188 A56 A64 B56 B64 C56 C64 D56 D64 E56 E64 F56 F64BS2

18、SP 95:1974 BSI 01-2000 3 Table 2 Tolerances 8 Example of call-up A grommet with bore diameter of 1 / 2inch and a groove width of 0.1 inch would be called up as: Dimensions in inches Dimension Range of sizes Tolerance V 1 / 16to 3 / 4inclusive 7 / 8to 2 +0.0000.020 +0.0000.040 W 3 / 16to 1 inclusive

19、1 1 / 8to 2 1 / 4 +0.0200.000 +0.0200.000 X all sizes +0.0300.000 Y all sizes +0.0100.000 Z all sizes +0.0200.000 Concentricity of diameters W andV Diameter V: 1 / 16to 1 / 2 9 / 16to 2 W in relation to V to beconcentricwithin 0.010 F.I.M. 0.020 F.I.M.BS 2SP 95: 1974 BSI 389 Chiswick High Road Londo

20、n W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision

21、. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Sec

22、retary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying s

23、tandards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishS

24、tandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details

25、 on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Member

26、ship Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may

27、be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, an

28、d size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.