BS 3087-10-1991 Pliers and nippers - Specification for dimensions of tools not standardized by ISO《夹扭钳和剪断钳 第10部分 非ISO标准工具尺寸规范》.pdf

1、BRITISH STANDARD BS3087-10: 1991 Pliers and nippers Part10: Specification for dimensions of tools not standardized by ISOBS3087-10:1991 This British Standard, having been prepared under the directionof the Machine, Engineers and Hand Tools Standards Policy Committee, waspublished under the authority

2、of the Standards Boardand comes into effect on 30April1991 BSI 10-1999 The following BSI references relate to the work on this standard: Committee reference MTE/15 Draft for comment87/71373 DC ISBN 0 580 17802 1 Committees responsible for this British Standard The preparation of this British Standar

3、d was entrusted by the Machine, Engineers and Hand Tools Standards Policy Committee (MTE/-) to Technical Committee MTE/15, upon which the following bodies were represented: British Coal Corporation British Telecommunications plc Consumer Policy Committee of BSI Department of Trade and Industry Mecha

4、nical Engineering and Manufacturing Technology Division (Mmt) Electricity Supply Industry in England and Wales Engineering Equipment and Materials Users Association Federation of British Engineers Tool Manufacturers Federation of British Hand Tool Manufacturers Handle Manufacturers Association Insti

5、tute of Production Engineers Ministry of Defence The following body was also represented in the drafting of the standard, through subcommittees and panels: National Association of Tool Dealers Amendments issued since publication Amd. No. Date CommentsBS3087-10:1991 BSI 10-1999 i Contents Page Commit

6、tees responsible Inside front cover Foreword ii 1 Scope 1 2 Fencing pliers 1 3 Pipe grip gas pliers 2 4 Duckbill pliers 2 Figure 1 Dimensions of fencing pliers 1 Figure 2 Dimensions of pipe grip gas pliers 3 Figure 3 Dimensions of duckbill pliers 4 Table 1 Dimensions of fencing pliers and maximum pe

7、rmissiblepermanentsetafter test 1 Table 2 Dimensions of pipe grip gas pliers and maximum permissiblepermanent set after test 3 Table 3 Dimensions of duckbill pliers and maximum permissible permanentset after test 3 Publication referred to Inside back coverBS3087-10:1991 ii BSI 10-1999 Foreword This

8、Part of BS3087 has been prepared under the direction of the Machine, Engineers and Hand Tools Standards Policy Committee and forms one of a number of British Standards which relate to a wide variety of hand tools. Parts1 to10 of this British Standard supersede BS3087:1959 which is withdrawn. It is r

9、ecommended that pliers should be legibly and indelibly marked with a name, trademark or the manufacturing code that will allow traceability. BS3087-10 1)should be marked either on the tool or on its associated packaging. A British Standard does not purport to include all the necessary provisions of

10、a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back

11、cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. 1) Marking BS3087-10:1991 on or in relation to a product represents a manufacturers declaration of conformity

12、, i.e.a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is therefore solely the responsibility of the person making the claim. Such a declaration is not to be confused with third party certification of conformity, which may

13、 also be desirable.BS3087-10:1991 BSI 10-1999 1 1 Scope This Part of BS3087 specifies the dimensions of pliers which are not standardized by the International Organization for Standardization (ISO) because their style and application are exclusive to the United Kingdom. The tools covered in this Par

14、t are of the following types: fencing pliers; pipe grip gas pliers; duckbill pliers. NOTEThe title of the publication referred to in this standard is given on the inside back cover. 2 Fencing pliers 2.1 Dimensions The dimensions of fencing pliers shall comply with those given inTable 1 andFigure 1.

15、2.2 Maximum permissible permanent set Fencing pliers shall comply with the maximum permissible permanent set given inTable 1 after application of the load test. Table 1 Dimensions of fencing pliers and maximum permissible permanent set aftertest(seeFigure 1) L L 1 W 4max. W 3max. T 1max. Load F Maxi

16、mum permanent set S mm 200 6 mm 100 mm 14 mm 32 mm 12 N 1500 mm 1.5 250 9 125 16 40 14 1600 1.5 300 15 150 20 44 16 1750 1.5 Figure 1 Dimensions of fencing pliers (seeTable 1)BS3087-10:1991 2 BSI 10-1999 2.3 Application of the load test Fencing pliers shall be tested in accordance with BS3087-4. Aft

17、er the load test, the permanent set shall not exceed the value given inTable 1. If the distance L 1is not suitable for the load test, the load F applied at a distance L 1shall be calculated from the following equation: 3 Pipe grip gas pliers 3.1 Dimensions The dimensions of pipe grip gas pliers shal

18、l comply with those given inTable 2 andFigure 2. 3.2 Maximum permissible permanent set Pipe grip gas pliers shall comply with the maximum permissible permanent set given inTable 2 after application of the load test. 3.3 Application of the load test Pipe grip gas pliers shall be tested in accordance

19、with BS3087-4. After the load test, the permanent set shall not exceed the value given inTable 2. If the distance L 1is not suitable for the load test, the load F applied at a distance L 1shall be calculated from the following equation: 4 Duckbill pliers 4.1 Dimensions The dimensions of duckbill pli

20、ers shall comply with those given inTable 3 andFigure 3. 4.2 Maximum permissible permanent set Duckbill pliers shall comply with the maximum permissible permanent set given inTable 3 after application of the load test. 4.3 Application of the load test Duckbill pliers shall be tested in accordance wi

21、th BS3087-4. After the load test, the permanent set shall not exceed the value given inTable 3. If the distance L 1is not suitable for the load test, the load F applied at a distance L 1shall be calculated from the following equation: where F is the load given inTable 1; L 1 is the distance from the

22、 centre of the joint rivet to the applied load given inTable 1; L 1 is the measured distance from the centre of the joint rivet to the applied load F. where F is the load given inTable 2; L 1 is the distance from the centre of the joint rivet to the applied load given inTable 2; L 1 is the measured

23、distance from the centre of the joint rivet to the applied load F. F FL 1 L 1 - = F FL 1 L 1 - = where F is the load given inTable 3; L 1 is the distance from the centre of the joint rivet to the applied load given inTable 3; L 1 is the measured distance from the centre of the joint rivet to the app

24、lied load F. F FL 1 L 1 - =BS3087-10:1991 BSI 10-1999 3 Table 2 Dimensions of pipe grip gas pliers and maximum permissible permanent set after test (seeFigure 2) Table 3 Dimensions of duckbill pliers and maximum permissible permanent set after test (seeFigure 3) L L 1 W 3max. T 1max. Load F Maximum

25、permanent set S mm 180 9 mm 80 mm 32 mm 12 N 1400 mm 1 230 11 100 42 14 1360 1 Figure 2 Dimensions of pipe grip gas pliers (seeTable 2) L L 1 W 4max. W 3max. T 1max. Load F Maximum permanent set S mm 140 mm 65 mm 1 mm 16 mm 10 N 600 mm 1BS3087-10:1991 4 BSI 10-1999 Figure 3 Dimensions of duckbill pl

26、iers (seeTable 3)BS3087-10:1991 BSI 10-1999 Publication referred to BS3087, Pliers and nippers. BS3087-4, Methods of test. BS3087-10: 1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It prese

27、nts the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI t

28、o improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax

29、:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089

30、969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and

31、 international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI a

32、re kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the c

33、opyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or oth

34、erwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.