BS 3858-1992 Specification for binding and identification sleeves for use on electric cables and wires《 电缆和电线用捆扎和识别套管规范》.pdf

1、BRITISH STANDARD BS3858:1992 Specification for Binding and identification sleeves for use on electric cables and wiresBS3858:1992 This British Standard, having been prepared under the directionof the Cables and Insulation Standards Policy Committee, was published underthe authority of the Standards

2、Board and comes intoeffect on 15October1992 BSI03-1999 First published February1965 Second edition October1992 The following BSI references relate to the work on this standard: Committee reference CIL/15 Draft for comment91 34145 DC ISBN 0 580 21021 9 Committees responsible for this British Standard

3、 The preparation of this British Standard was entrusted by the Cables and Insulation Standards Policy Committee (CIL/-) to Technical Committee CIL/15, upon which the following bodies were represented: British Ceramic Research Ltd. British Industrial Ceramic Manufacturers Association Department of Tr

4、ade and Industry (National Measurement Accreditation Service) EEA (the Association of the Electronics, Telecommunications and Business Equipment Industries) Electrical and Electronic Insulation Association (BEAMA Ltd.) Electricity Association Ministry of Defence Rotating Electrical Machines Associat

5、ion (BEAMA Ltd.) Transmission and Distribution Association (BEAMA Ltd.) The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Adhesive Tape Manufacturers Association Association of Electrical Machinery Trades British Rubber Manufacturers Associ

6、ation Ltd. Electronic Components Industry Federation Amendments issued since publication Amd. No. Date CommentsBS3858:1992 BSI 03-1999 i Contents Page Committees responsible Inside front cover Foreword ii Introduction 1 1 Scope 1 2 References 1 3 Types 1 4 Materials and finishes 1 5 Colour 1 6 Dimen

7、sions 2 7 Printing 4 8 Packaging 4 9 Tests 5 Annex A (normative) Tests 6 Figure 1 Arrangement of characters 4 Table 1 Dimensions of type1 sleeves 2 Table 2 Dimensions of type3 sleeves 2 Table 3 Dimensions of type4 sleeves 2 Table 4 Dimensions of type5 sleeves 3 Table 5 Recommended bore and length co

8、mbinations 3 Table 6 Size and repetition of characters 4 Table 7 Colour codes 4 Table A.1 Ageing temperature 6 List of references 10BS3858:1992 ii BSI 03-1999 Foreword This British Standard has been prepared under the direction of the Cable and Insulation Standards Policy Committee. The sleeves with

9、in the field of application of this British Standard are for general purpose use. They are not intended for use as primary insulation. This British Standard supersedes BS3858:1965 which is withdrawn. Flexible sleeving for electrical purposes are within the fields of application of BS2848, BS6893-1 a

10、nd BS6893-2, while elastomeric sleeves for aircraft electric cables and equipment wires are specified in BS3G198-1. It is envisaged that BS2848 will ultimately be withdrawn and replaced by a Part of BS6893. The different wall thicknesses of polychloroprene sleeves of type1 and type2 of BS3858:1965 h

11、ave been incorporated into type1 of this revision. WARNING. This standard calls for the use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supplier or the user from

12、statutory obligations relating to health and safety at any stage of manufacture or use. Product certification. Users of this British Standard are advised to consider the desirability of third party certification of product conformity with this British Standard based on testing and continuing product

13、 surveillance which may be coupled with assessment of a suppliers quality systems against the appropriate Part of BS5750. Enquiries as to the availability of third party certification schemes are forwarded by BSI to the Association of Certification bodies. If a third party certification scheme does

14、not already exist, users should consider approaching an appropriate body from the list of association members. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Britis

15、h Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments inc

16、orporated. This will be indicated in the amendment table on theinside front cover.BS3858:1992 BSI 03-1999 1 Introduction Type1,3 and4 sleeves are subject to stiffening at subzero temperatures, and should not be flexed in use at these temperatures. Sleeves are normally expanded in use, up to twice th

17、eir nominal bore for types1,4 and5, and one and a half times their nominal bore for type3 sleeves. Type1,3 and4 sleeves are suitable for use where there may be occasional contamination by mineral lubricating oils and certain hydraulic fluids. Type5 sleeves have limited resistance to hydrocarbon flui

18、ds and should not be used where such contamination is likely. All sleeves are available in a range of colours, and may have characters or legends printed on them for identification purposes. 1 Scope This British Standard specifies requirements and tests for binding and identification sleeves intende

19、d for use on electric cables and insulated wires. NOTEThese sleeves are not for use as primary insulation The standard applies to sleeves of the following types: a) type1 sleeves are polychloroprene and suitable for temperature ranges of 65C to70C; b) type3 sleeves are poly(vinyl chloride) (PVC) and

20、 suitable for temperature ranges of 65C to70C; c) type4 sleeves are PVC/nitrile and suitable for temperature ranges of 65C to70C; d) type5 sleeves are silicone and suitable for temperature ranges of 65C to150C. 2 References 2.1 Normative references This British Standard incorporates, by reference, p

21、rovisions from specific editions of other publications. These normative references are cited at the appropriate points in the text and the publications are listed on the page 10. Subsequent amendments to, or revisions of, any of these publications apply to this British Standard only when incorporate

22、d in it by updating or revision. 2.2 Informative references This British Standard refers to other publications that provide information or guidance. Editions of these publications current at the time of issue of this standard are listed on page 10, but reference should be made to the latest editions

23、. 3 Types Sleeves shall be one of the following types. a) Type1 sleeves are polychloroprene rubber sleeves having increasing wall thicknesses over a range of bore sizes, with fairly wide permissible tolerances on bore sizes. NOTE 1These are available in three different wall thickness ranges (a, b an

24、d c). b) Type3 sleeves are based on poly(vinyl chloride) (PVC) polymers, copolymers, or blends thereof and have wall thicknesses which increase slightly with bore sizes. They shall conform to either type E3of BS2571 or type4 of BS6746. NOTE 2Tolerances on wall thickness and bore are closer than for

25、types1,4 and5. c) Type4 sleeves are based on a mixture or copolymer of acrylonitrile-butadiene rubber and PVC and have wall thicknesses which increase with bore size. NOTE 3Tolerances on wall and bore sizes are similar to type1. d) Type5 sleeves are silicone rubber and have a range of permissible wa

26、ll thicknesses for all bore sizes. NOTE 4These are available in three different wall thickness ranges (a, b and c). 4 Materials and finishes The sleeves shall be smooth and free from bubbles, pinholes, creases, and other defects in appearance (see clause9.1). Type1 material shall contain no natural

27、rubber, reclaim, nor ground, vulcanized waste. NOTESee BS7164-7.1. 5 Colour The colour shall be one of the following: pink; orange; violet; green/yellow stripe; black; yellow; grey; brown; green; white; red; blue; uncoloured transparent (for type3 only); uncoloured translucent (for type3 and type5 o

28、nly).BS3858:1992 2 BSI 03-1999 The colour shall be uniform. NOTEWhere relevant the colour should be a reasonable match to the equivalent colour in BS6746C. Table 1 Dimensions of type1 sleeves 6 Dimensions Bore sizes of sleeves of types1,3,4and5shall comply with the dimensions shown in Table 1, Table

29、 2, Table 3 andTable 4respectively. NOTENominal lengths are3mm, 5mm, 7mm, 10mm, 15mm, 20mm, 25mm, 35mm, 45mm, 55mm and75mm and the recommended combinations of bore and length are shown inTable 5. Table 2 Dimensions of type3 sleeves Table 3 Dimensions of type4 sleeves Dimensions in millimetres Intern

30、al diameter Wall thickness Nominal Actual Type1a Type1b Type1c min. max. min. max. min. max. min. max. 0.5 0.4 0.7 0.4 0.6 0.8 0.6 0.9 0.4 0.6 1.0 0.9 1.2 0.4 0.6 1.2 1.0 1.4 0.4 0.6 0.6 0.8 1.5 1.3 1.8 0.5 0.7 0.7 0.9 2.0 1.7 2.3 0.5 0.7 0.7 0.9 2.5 2.1 2.9 0.5 0.7 0.7 0.9 3.0 2.5 3.5 0.5 0.7 0.7 0

31、.9 4.0 3.3 4.6 0.5 0.8 0.7 1.0 0.9 1.2 5.0 4.2 5.8 0.5 0.8 0.7 1.0 0.9 1.2 8.0 6.8 9.2 0.5 0.8 0.7 1.1 1.0 1.5 10.0 8.6 11.4 0.5 0.8 0.8 1.2 1.2 1.8 12.0 10.4 13.6 0.5 0.8 0.8 1.3 1.3 1.9 16.0 14.0 18.0 0.5 0.9 0.9 1.5 1.5 2.1 20.0 17.5 22.5 0.5 0.9 0.9 1.5 1.7 2.4 25.0 21.5 28.5 0.5 0.9 0.9 1.5 1.7

32、 2.4 Dimensions in millimetres Internal diameter Wall thickness Nominal Actual min. max. min. max. 0.5 0.4 0.6 0.2 0.4 0.8 0.7 0.9 0.2 0.4 1.0 0.85 1.15 0.2 0.4 1.2 1.05 1.35 0.2 0.4 1.5 1.35 1.65 0.2 0.4 2.0 1.85 2.15 0.2 0.4 2.5 2.35 2.65 0.2 0.4 3.0 2.85 3.15 0.2 0.4 4.0 3.75 4.25 0.2 0.4 5.0 4.7

33、5 5.25 0.2 0.4 6.0 5.75 6.25 0.2 0.4 8.0 7.75 8.25 0.4 0.6 10.0 9.5 10.5 0.4 0.6 12.0 11.5 12.5 0.4 0.6 16.0 15.5 16.5 0.4 0.6 20.0 19.5 20.5 0.4 0.6 25.0 24.5 25.5 0.4 0.6 Dimensions in millimetres Internal diameter Wall thickness Nominal Actual min. max. min. max. 0.5 0.4 0.7 0.5 0.7 0.8 0.6 0.9 0

34、.5 0.7 1.0 0.9 1.2 0.5 0.7 1.5 1.3 1.8 0.5 0.7 2.0 1.7 2.3 0.5 0.7 3.0 2.5 3.5 0.8 1.2 4.0 3.3 4.6 0.8 1.2 5.0 4.2 5.8 0.8 1.2 8.0 6.8 9.2 1.0 1.5 10.0 8.6 11.4 1.0 1.8 12.0 10.4 13.6 1.0 1.8 16.0 14.0 18.0 1.0 1.8 20.0 17.5 22.5 1.0 1.8 25.0 21.5 28.5 1.0 1.8BS3858:1992 BSI 03-1999 3 Table 4 Dimens

35、ions of type5sleeves Table 5 Recommended bore and length combinations Dimensions in millimetres Internal diameter Wall thickness Nominal Actual Type5a Type5b Type5c min. max. min. max. min. max. min. max. 0.5 0.4 0.7 0.4 0.6 0.55 0.85 0.8 1.2 0.8 0.6 0.9 0.4 0.6 0.55 0.85 0.8 1.2 1.0 0.9 1.2 0.4 0.6

36、 0.55 0.85 0.8 1.2 1.5 1.3 1.8 0.4 0.6 0.55 0.85 0.8 1.2 2.0 1.7 2.3 0.4 0.6 0.55 0.85 0.8 1.2 2.5 2.1 2.9 0.4 0.6 0.55 0.85 0.8 1.2 3.0 2.5 3.5 0.4 0.6 0.55 0.85 0.8 1.2 4.0 3.3 4.6 0.4 0.6 0.55 0.85 0.8 1.2 5.0 4.2 5.8 0.4 0.6 0.55 0.85 0.8 1.2 6.0 5.1 6.9 0.4 0.6 0.55 0.85 0.8 1.2 8.0 6.8 9.2 0.4

37、 0.6 0.55 0.85 0.8 1.2 10.0 8.6 11.4 0.4 0.6 0.55 0.85 0.8 1.2 12.0 10.4 13.6 0.4 0.6 0.55 0.85 0.8 1.2 16.0 14.0 18.0 0.4 0.6 0.55 0.85 0.8 1.2 Dimensions in millimetres Nominal internal diameter Nominal length 0.5 3 5 7 10 15 20 25 35 0.8 3 5 7 10 15 20 25 35 1.0 3 5 7 10 15 20 25 35 1.2 3 5 7 10

38、15 20 25 35 1.5 3 5 7 10 15 20 25 35 2.0 5 7 10 15 20 25 35 45 2.5 5 7 10 15 20 25 35 45 3.0 5 7 10 15 20 25 35 45 4.0 5 7 10 15 20 25 35 45 5.0 5 7 10 15 20 25 35 45 6.0 5 7 10 15 20 25 35 45 8.0 10 15 20 25 35 45 10.0 10 15 20 25 35 45 12.0 10 15 20 25 35 45 16.0 10 15 20 25 35 45 55 75 20.0 10 15

39、 20 25 35 45 55 75 25.0 10 15 20 25 35 45 55 75BS3858:1992 4 BSI 03-1999 7 Printing When required, sleeves shall be indelibly printed with a character or legend. Such printing shall not be affected by normal handling. The printing shall be black, blue-black or white to provide sufficient contrast wi

40、th the sleeve colour. Where there is a possibility of misinterpretation, the characters shall be either: a) followed by a period in the lower right, i.e.A B C M. W. 6. 7 8 9. 0; b) underlined, i.e.A B C MW67 8 90. The printing shall be longitudinal on the sleeve,Figure 1. The size of characters and

41、the number of times they are printed on each sleeve shall be as shown inTable 6. When the sleeves are marked more than once, the printing shall be approximately equally spaced around the sleeve. Table 6 Size and repetition of characters If a transparent overlay is used to protect the print it shall

42、be considered as part of the sleeve for the purposes of the appropriate tests. Where colour coded sleeves are required the colour code shall be as inTable 7. Table 7 Colour codes 8 Packaging Boxes or packages containing the sleeves shall be marked with: a) the number and date of this British Standar

43、d 1)i.e.BS3858:1992; b) the type (e.g.type1a); c) the nominal bore in millimetres; d) the nominal length in millimetres; e) the legend when printed; f) the nominal quantity of the sleeves; Figure 1 Arrangement of characters Nominal internal diameter of sleeve Nominal height of character Number of ti

44、mes printed around circumference mm mm 0.5 1.6 min. 1 0.8 to1.2 2.0 1 1.5 2.0 2 2.0to4.0 2.5 2 5.0to6.0 4.5 2 8.0to12.0 4.5 4 15.0to25.0 6.0 4 Colour of Sleeve Numeral Colour of sleeve Numeral Black 0 Green 5 Brown 1 Blue 6. or6 Red 2 Violet 7 Orange 3 Grey 8 Yellow 4 White 9. or9 NOTEThe number and

45、 colour relationships are as given in BS1852:1975. 1) Marking BS3858:1992 on or in relation to a product represents a manufacturers declaration of conformity, i.e.a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is solely

46、the claimants responsibility. Such a declaration is not to be confused with third party certification of conformity, which may also be desirable.BS3858:1992 BSI 03-1999 5 g) the manufacturer or suppliers name. Unless packed in transparent packets, the outside of the packet shall be marked to show th

47、e colour of the sleeves. 9 Tests 9.1 Appearance for all types When tested in accordance withA.1 the sleeves shall conform to clauses4 and5 and where printed clause7. 9.2 Dimensions for all types When measured in accordance withA.2, the bore and wall thickness shall comply with clause6. In cases of d

48、isagreement, an optical method having an accuracy of0.025mm or greater shall be used. 9.3 Circumferential extension for types1,4and5 When tested in accordance withA.3 at least two rings shall stand each test without breaking. 9.4 Tension set for types1, 4and5 When tested in accordance withA.4 for bo

49、th specimens the tension set shall be no more than25%. 9.5 Ozone resistance for types1 and4 When tested in accordance withA.5 there shall be no signs of cracking when examined using normally corrected vision. 9.6 Silver staining for types1, 4and5 When tested in accordance withA.6 no stain shall be darker than the standard shade. 9.7 Proof voltage for types1, 4and5 When tested in accordance withA.7 there shall be no flashover, tracking, breakdown or erosion