BS 3876-1-1990 Rope rollers pulleys mountings and assemblies for colliery track haulage - Specification for parallel barrel rollers mountings and assemblies《煤井轨道运输用缆绳滚筒、滑轮、支架和组件 第1.pdf

1、BRITISH STANDARD BS3876-1: 1990 Rope rollers, pulleys, mountings and assemblies for colliery track haulage Part1: Specification for parallel barrel rollers, mountings and assemblies UDC622.33.005:622.625.5:625.52:006.3/.8BS3876-1:1990 This British Standard, having been prepared under the directionof

2、 the Mining and Quarrying Requisites StandardsPolicy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 30June1990 BSI11-1999 First published March1965 Second edition June1990 The following BSI references relate to the work on this standard: Committee reference MQ

3、E/18 Draft for comment88/74302DC ISBN 0 580 17993 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Mining and Quarrying Requisites Standards Policy Committee (MQE/-) to Technical Committee MQE/18, upon which the following bodies were re

4、presented: Association of British Mining Equipment Companies British Foundry Association British Steel Industry Federation of Wire Rope Manufacturers of Great Britain Health and Safety Executive Institution of Mining Electrical and Mining Mechanical Engineers Amendments issued since publication Amd.

5、 No. Date CommentsBS3876-1:1990 BSI 11-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 General 1 4 Dimensions and shape of roller components and mountings 1 5 Materials 6 6 Manufacture 8 7 Marking 9 Appendix A Information supplied by the purchas

6、er 10 Appendix B Information to be provided by the supplier 10 Appendix C General recommendations for the design and operating speedsofrollers 10 Appendix D Typical clause relating to inspection that the purchaser maychooseto write into his order or contract for the supply of rollers, mountingsand a

7、ssemblies to this Part of BS3876 10 Figure 1 Typical cast roller 2 Figure 2 Typical fabricated roller 2 Figure 3 Typical roller having rope wind back facility 6 Figure 4 Typical mounting and details of bearing portions 7 Figure 5 Method of testing rollers for eccentricity 6 Figure 6 Relationship bet

8、ween rope speed and roller speed 11 Table 1 Dimensions of cast rollers 3 Table 2 Dimensions of fabricated rollers 4 Table 3 Dimensions of rollers with internal rolling bearings having ropewindback facility 5 Table 4 Dimensions of mountings 6 Table 5 Bearing characteristics and designations 8 Publica

9、tions referred to Inside back coverBS3876-1:1990 ii BSI 11-1999 Foreword This Part of BS3876 has been prepared under the direction of the Mining and Quarrying Requisites Standards Policy Committee (MQE/-) and is a full technical revision of both BS3876-1:1965 and BS3876-4:1966 both of which are with

10、drawn. The other Parts in the revised edition of BS3876 are as follows: Part2: Specification for vertical spindle pulleys, mountings and assemblies; Part5: Specification for suspended pulley assemblies and clamps. In the revised Parts, the following points should be noted: a) tapered rollers, covere

11、d in BS3876-2:1965, are now omitted from the revised Part2; b) vertical rollers, which were included in the1965 edition of Part2, are now omitted as it is considered the parallel barrel rollers specified in Part1 can be used in the vertical mode; c) horizontal spindle pulleys, covered in the1965 edi

12、tion of Part2, are relocated in Part5 of the revised edition; d) Part3:1965 has been withdrawn because there is no longer any requirement for rollers with non-metallic rope bearing surfaces; e) the requirements for mountings for parallel barrel rollers, previously specified in BS3876-4:1966, have be

13、en revised and incorporated into this expanded edition of Part1; there is therefore no need for retention or revision of a separate Part4. During the revision, all dimensions have been metricated and these are not necessarily straight conversions from the imperial dimensions previously adopted. In p

14、articular, barrel diameters have been adjusted to align with the outside diameters of metric tubes now available. Product certification. Users of this British Standard are advised to consider the desirability of third party certification of product conformity with this British Standard based on test

15、ing and continuing surveillance, which may be coupled with assessment of a suppliers quality systems against the appropriate Part of BS5750. Enquiries as to the availability of third party certification schemes will be forwarded by BSI to the Association of Certification Bodies. If a third party cer

16、tification scheme does not exist, users should consider approaching an appropriate body from the list of Association members. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Complianc

17、e with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to12, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had a

18、mendments incorporated. This will be indicated in the amendment table on the inside front cover.BS3876-1:1990 BSI 11-1999 1 1 Scope This Part of BS3876 specifies requirements for fabricated and cast steel rope rollers, mountings and roller assemblies intended for use in colliery track haulage. This

19、Part applies to a) rollers, with or without incorporated wind-back facilities and supplied without mountings, for which the diameters of the roller barrels do not exceed the lengths of the rollers to the outsides of their flanges; b) mounting, either high or low type and dependant upon roller diamet

20、ers; and c) roller assemblies that comprise both the rollers and the mountings. NOTE 1Appendix A gives the information which should be supplied by the purchaser, in his enquiry and/or order for rollers, mountings or assemblies in accordance with this Part of BS3876. NOTE 2Appendix B gives the inform

21、ation that will be required by the purchaser, to be provided by the supplier, prior to the supply of rollers, mountings or assemblies in accordance with this Part of BS3876. NOTE 3Appendix C gives general recommendations for the design and operating speeds for colliery track haulage rollers. NOTE 4N

22、o inspection requirements are specified in this Part of BS3876. However, a typical requirement that the purchaser may choose to write into his order or contract for rollers, mountings or assemblies to this Part is given in Appendix D. NOTE 5The titles of the publications referred to in this Part of

23、BS3876 are listed on the inside back cover. 2 Definitions For the purposes of this Part of BS3876, the following definitions apply. 2.1 barrel that part of the roller cylinder on which the rope runs 2.2 roller a cylinder that is free to rotate to support or guide a moving rope, having a parallel bar

24、rel, parallel or taper sided flanges, windback facilities when required, complete with spindle and bearings 2.3 roller end/end cap a casting or fabrication at each end of the cylinder that contains the flange, bearing housing and windback facility when required NOTEIn the case of cast roller cylinde

25、rs, the ends are parts of the casting. In the case of fabricated roller cylinders, the end caps are fixed by welding or by tie-rods. 2.4 windback facility a scrolled configuration forming part of the roller end/end cap the effect of which is to impart a lateral movement, towards the roller barrel, t

26、o any moving haulage rope in contact with the scroll in either direction of roller rotation 2.5 throw (eccentricity) the total variation from true running of the periphery of the barrel when rotated on the spindle 1) 2.6 mounting the frame to which the roller is, or is to be, attached 2.7 roller ass

27、embly the roller and its mounting 3 General The roller components and mountings shall comply with the requirements specified in clauses4 to7, as appropriate. 4 Dimensions and shape of roller components and mountings 4.1 Dimensions The dimensions of the roller components and mountings shall be as giv

28、en in Table 1 to Table 4. NOTEFor convenience, typical rollers and mountings are illustrated in Figure 1 to Figure 4 which identify the dimensions referred to in Table 1 to Table 4. 4.2 Eccentricity of the barrels The eccentricity of the barrel when determined at the fixed points BB shown in Figure

29、5 (i.e.the radial run out as defined in BS308-3), shall not exceed the following: a) 1.5mm, for barrels up to and including168mm diameter; and b) 2.3mm, for barrels exceeding168mm diameter. 1) SeeFigure 5.BS3876-1:1990 2 BSI 11-1999 NOTEThis figure does not purport to show design details. Figure 1 T

30、ypical cast roller NOTEThis figure does not purport to show design details. Figure 2 Typical fabricated rollerBS 3876-1:1990 BSI 11-1999 3 Table 1 Dimensions of cast rollers (see also Figure 1) Roller ref. no. Diameter of barrel Length of roller outside end caps Spindle Diameter end cap Length Minim

31、um bearing housing diameter Minimum bearing housing length Flange thickness Barrel thickness Diameter Length A ( 1.5mm) B ( 1.5mm) C (seeNOTE) D ( 1.0mm) E ( 1.5mm) F ( 1.0mm) G H K ( 1.0mm) L ( 1.0mm) 114/230 114/300 114/600 127/150 127/230 127/300 168/200 168/250 168/300 168/450 168/600 193/200 19

32、3/250 193/300 193/450 193/600 219/300 273/300 273/450 305/305 305/450 mm 114 114 114 127 127 127 168 168 168 168 168 193 193 193 193 193 219 273 273 305 305 mm 230 300 600 150 230 300 200 250 300 450 600 200 250 300 450 600 300 300 450 305 450 mm 19 19 19 19 19 19 25 25 25 25 25 25 25 25 25 25 25 25

33、 25 25 25 mm 330 400 700 250 330 400 300 350 400 550 700 300 350 400 550 700 400 400 550 405 550 mm 150 150 150 165 165 165 210 210 210 210 210 235 235 235 235 235 260 320 320 355 355 mm 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 mm 65 65 65 65 65 65 80 80 80 80 80 80 80 80 80 80

34、 100 100 100 100 100 mm 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 35 35 35 35 35 mm 10 10 10 10 10 10 11 11 11 11 11 11 11 11 11 11 13 13 13 13 13 mm 10 10 10 10 10 10 11 11 11 11 11 11 11 11 11 11 13 13 13 13 13 NOTEFor tolerances on the spindle diameter, see6.3.BS 3876-1:1990 4 BSI 11-1999 T

35、able 2 Dimensions of fabricated rollers (see also Figure 2) Roller ref.no. Diameter of barrel Length of roller outside end caps Spindle Diameter end cap Length Minimum bearing housing diameter Minimum bearing housing length Flange thickness Barrel thickness Diameter Length A ( 1.5mm) B ( 1.5mm) C (s

36、eeNOTE) D ( 1.0mm) E ( 1.5mm) F ( 1.0mm) G H K ( 1.0mm) L ( 1.0mm) 114/230 114/300 114/600 127/150 127/230 127/300 168/200 168/250 168/300 168/450 168/600 193/200 193/250 193/300 193/450 193/600 219/300 273/300 273/450 305/305 305/450 mm 114.3 114.3 114.3 127.0 127.0 127.0 168.3 168.3 168.3 168.3 16

37、8.3 193.7 193.7 193.7 193.7 193.7 219.1 273.0 273.0 305.0 305.0 mm 230 300 600 150 230 300 200 250 300 450 600 200 250 300 450 600 300 300 450 305 450 mm 19 19 19 19 19 19 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 mm 330 400 700 250 330 400 300 350 400 550 700 300 350 400 550 700 400 400 550 405

38、550 mm 150 150 150 165 165 165 210 210 210 210 210 235 235 235 235 235 260 320 320 355 355 mm 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 mm 65 65 65 65 65 65 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 mm 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 35 35 35 35 35 mm 10

39、10 10 10 10 10 11 11 11 11 11 11 11 11 11 11 13 13 13 13 13 mm 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 NOTEFor tolerances on the spindle diameter, see6.3.BS 3876-1:1990 BSI 11-1999 5 Table 3 Dimensions of rollers with internal rolling bearings having rope wi

40、nd back facility (seealso Figure 3) Roller ref.no. Diameter of barrel Length of roller outside flange Spindle Diameter end cap Length a Minimum bearing housing diameter Minimum bearing housing length Flange thickness Barrel thickness Diameter Length A ( 1.5mm) B ( 1.5mm) C (seeNOTE) D ( 1.0mm) E min

41、 F ( 1.0mm) G H max K ( 1.0mm) L ( 1.0mm) 114/230 WB 114/300 WB 114/600 WB 168/200 WB 168/250 WB 168/300 WB 168/450 WB 168/600 WB mm 114.3 114.3 114.3 168.3 168.3 168.3 168.3 168.3 mm 230 300 600 200 250 300 450 600 mm 19 19 19 25 25 25 25 25 mm 330 400 700 300 350 400 550 700 mm 130 130 130 180 180

42、 180 180 180 mm 50 50 50 50 50 50 50 50 mm 45 45 45 50 50 50 50 50 mm 30 30 30 30 30 30 30 30 mm 50 50 50 50 50 50 50 50 mm 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 NOTEFor tolerances on the spindle diameter, see6.3. a Minimum internal bearing housing diameter.BS3876-1:1990 6 BSI 11-1999 Table 4 Dimension of

43、 mountings 5 Materials 5.1 General Subject to the requirements of5.2, the materials used in the construction of the rollers and mountings shall be in accordance with5.3 and5.4 respectively. 5.2 Light metals In the construction of the rollers, mountings and assemblies, no metal shall be used that con

44、tains more than: a) 15% (m/m) in total of aluminium, magnesium and titanium; and b) 6% (m/m) in total of magnesium and titanium. Paints and coatings containing any of the metals aluminium, magnesium and titanium shall not be used. 5.3 Materials for rollers 5.3.1 Fabricated rollers 5.3.1.1 The cylind

45、ers for fabricated rollers shall be manufactured from seamless or welded steel tube having a Brinell hardness of at least300BHN and not more than400BHN throughout the section. 5.3.1.2 The roller end caps shall be manufactured from any of the materials given ina) toc) as follows. a) Cast steel end ca

46、ps: from either of the cast steels specified in5.3.2. b) Malleable cast iron end caps: from whiteheart or blackheart malleable cast iron in accordance with BS6681. c) Wrought steel plate end caps: from either of the following: 1) carbon steel in accordance with BS970, grade070M20; or 2) weldable str

47、uctural steel in accordance with BS4360, grade43A. NOTEThis figure does not purport to show design details. Figure 3 Typical roller having rope wind back facility Roller reference no. Dimension X 114/230 to127/300 168/200 to219/300 273/300 to305/450 mm 185 270 375 Figure 5 Method of testing rollers

48、for eccentricityBS 3876-1:1990 BSI 11-1999 7 Figure 4 Typical mounting and details of bearing portionsBS3876-1:1990 8 BSI 11-1999 5.3.2 Cast rollers Cast steel roller cylinders, with integral ends, shall be made from either of the following steels: a) carbon steel in accordance with BS3100, steelA3;

49、 or b) low alloy(1% chromium) steel in accordance with BS3100, steel BW4. 5.3.3 Spindles Spindles shall be made from wrought steel in accordance with BS970, grade070M20, with a minimum tensile strength of430N/mm 2 . 5.3.4 Bearings Bearings shall be double sealed, grease filled, single row radial ball bearings in accordance with BS292-1. NOTE 1The use of seize-resistant bearings having polyamide cages is preferred. The types of bearings to be used for particular applications shall be as given in Table 5. Th