BS 3F 114-1995 Specification for 80 g m2 cotton madapolam fabric《每平方米重80克马德波勒姆细布纤维规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS3F 114:1995 Specification for 80g/m 2cotton madapolam fabric UDC 629.73:677.21.064.1BS3F114:1995 This British Standard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes intoef

2、fect on 15 June1995 BSI08-1999 First published1963 Second edition February1975 Third edition June1995 The following BSI references relate to the work on this standard: Committee reference ACE/54 Draft for comment94/706285 DC ISBN 0 580 24208 0 Committees responsible for this British Standard The pre

3、paration of this British Standard was entrusted to Technical Committee ACE/54, Wide woven and coated fabrics for aerospace purposes, upon which the following bodies were represented: British Fabric Association British Rubber Manufacturers Association Ltd. British Textile Confederation Ministry of De

4、fence Society of British Aerospace Companies Ltd. Society of Dyers and Colourists Textile Finishers Association Amendments issued since publication Amd. No. Date CommentsBS3F114:1995 BSI 08-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 General

5、1 4 Yarn 1 5 Weave 1 6 Finish 1 7 Construction and properties 1 8 Packaging 1 9 Identification 1 Table 1 General requirements (given in BS F100) 2 Table 2 Construction and properties 2 List of references Inside back coverBS3F114:1995 ii BSI 08-1999 Foreword This British Standard is one of a series f

6、or textiles of a quality suitable for aerospace purposes and constitutes a revision of BS2F114:1975, which is withdrawn. It differs from the previous edition in that the quality requirements specified in the latest edition of BSF100 have been identified. NOTEThe latest revision of an Aerospace Serie

7、s standard is indicated by a prefix number. This standard specifies pentachlorophenyl laurate (PCPL) as a rot-proofing treatment. Alternative treatments are under development, and this standard will be updated to delete PCPL as soon as a suitable alternative treatment for aerospace materials is avai

8、lable. WARNING. This standard calls for the use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supplier or the user from statutory obligations relating to health and

9、 safety at any stage of manufacture or use. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligation

10、s. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the insid

11、e front cover.BS3F114:1995 BSI 08-1999 1 1 Scope This British Standard specifies requirements for a nominal80g/m 2cotton madapolam fabric for aerospace purposes. 2 References 2.1 Normative references This standard incorporates, by dated or undated reference, provisions from other publications. These

12、 normative references are made at the appropriate places in the text and the cited publications are listed on the inside back cover. For dated references, only the edition cited applies; any subsequent amendments to or revisions of the cited publication apply to this standard only when incorporated

13、in the reference by amendment or revision. For undated references, the latest edition of the cited publication applies, together with any amendments. 2.2 Informative references This standard refers to other publications that provide information or guidance. Editions of these publications current at

14、the time of issue of this standard are listed on the inside back cover, but reference should be made to the latest editions. 3 General In addition to the requirements specified in clauses4 to9 of this standard, the requirements and tests of BSF100, as listed in Table 1, shall apply. 4 Yarn The fabri

15、c shall be manufactured from cotton yarn. NOTESingles yarns of100dtex grey count for the warp and92dtex grey count for the weft have been found suitable to provide a finished fabric which conforms to Table 2. 5 Weave The weave shall be plain. 6 Finish 6.1 General The fabric shall be supplied either:

16、 a) scoured and rendered rot-resistant; or b) scoured, dyed and rendered rot-resistant. 6.2 Rot-resistance The fabric shall be rendered rot-resistant by treatment with pentachlorophenyl laurate (PCPL) in accordance with BS2087-1:1992, normal process. 6.3 Dyeing If dyeing is required, the colour spec

17、ified by the purchaser shall be documented as stated in clause9. 7 Construction and properties 7.1 General The finished fabric shall conform to7.2 and Table 2. 7.2 Reaction to indicators 7.2.1 Each piece of finished fabric shall be spotted with aqueous solutions of bromo-cresol green and thymol blue

18、. The indicators shall be absorbed immediately on application. 7.2.2 The finished fabric shall show a blue or greenish-blue colour when spotted with with bromo-cresol green and a distinct yellow colour when spotted with with thymol blue. 8 Packaging The fabric shall be made up at full width, on pole

19、s longer than the width of the fabric, or on suitable tubes having a length equal to the width of the fabric. It shall be made up in continuous pieces without joins, rolled tightly and free from creases. 9 Identification The following information, supplied by the purchaser to identify the fabric for

20、 ordering purposes, shall be fully documented: a) the number of this British Standard, i.e.BS3F114; b) the designation given in Table 2, i.e.no.343; and, if required dyed: c) the colour, specified by reference to a British Standard, e.g.BS381C, or otherwise by reference to a pattern. NOTEThis specif

21、ication may be codified; e.g.fabric required dyed NATO green may be identified as BS3F114/343/BS381C/285.BS3F114:1995 2 BSI 08-1999 Table 1 General requirements (given in BSF100) Table 2 Construction and properties Section of BS F100 Section title Requirements and tests 1 General All requirements 2

22、Quality requirements Requirements for the manufacture of wide fabrics Requirements for dyed textiles Requirements for dimensions and tolerances: general and wide fabrics Requirements for freedom from corrosive impurities Requirements for freedom from faults 3 Physical tests Test for the determinatio

23、n of mass of wide fabrics Tests for breaking strength and extension under force of wide fabrics 4 Chemical tests If required by section2, further tests for freedom from corrosive impurities Designation Minimum number of threads per centimetre a Maximum mass/area Minimum average breaking strength per

24、50mm width N Warp Weft g/m 2 Warp Weft No.343 37.5 35.5 85 290 290 a Calculated from the number in a measured length of not less than2cm.BS3F114:1995 BSI 08-1999 List of references (see clause 2) Normative references BSI publications BRITISH STANDARDS INSTITUTION, London BS5F100:1991, Procedure for

25、inspection and testing of textiles for aerospace purposes. BS2087, Preservative textile treatments. BS2087-1:1992, Specification for treatments. Informative references BSI publications BRITISH STANDARDS INSTITUTION, London BS381C:1988, Specification for colours for identification, coding and special

26、 purposes. BS3F 114:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisi

27、ons BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigu

28、ity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automat

29、ically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI imp

30、lementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic i

31、nformation services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standard

32、s. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under th

33、e Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementi

34、ng the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.