BS 3F 69-1979 Specification for packaging and identification of vulcanized rubber items《硫化橡胶产品包装和识别标志规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIES CONFIRMED JANUARY 1988 3F 69:1979 (Superseding British Standard 2F69) Incorporating Amendment No.1 Specification for Packaging and identification of vulcanized rubber items UDC 629.7:678.4.063:621.7987773F 69:1979 This British Standard, having been prepared under th

2、e directionof the British AerospaceStandards Committee,was published underthe authority of the Executive Board on 31 January1979 BSI 04-1999 The following BSI references relate to the work on this standard: Committee reference ACE/25 Draft for comment78/72283DC ISBN 0 580 10675 6 Foreword This Briti

3、sh Standard was first published in1968under the authority of the Aerospace Industry Standards Committee at the request of the Society of British Aerospace Companies Limited. This revision takes into account accumulated experience since it was first published. The provision for identification by a st

4、andard colour code has been deleted but colour coding may continue to be used by arrangement between the user and the supplier. Items packaged to the requirements of this standard will also meet the packing requirements of ISO1749:1973 “Aircraft Elastomeric sealing rings Packaging and identification

5、”. The identification requirements of ISO1749, however, differ from those specified in this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standar

6、d does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, page1 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in

7、the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue Comments 9771 February 1998 Indicated by a sideline in the margin3F 69:1979 BSI 04-1999 i Contents Page Foreword Inside front cover 1 Scope 1 2 Reference 1 3 Packaging 1 4 Identification on pack

8、aging 1 5 Identification by colour code 1ii blank3F 69:1979 BSI 04-1999 1 1 Scope 1.1 This British Standard specifies the requirements for the packaging and identification when packaged of vulcanized rubber materials, components and assemblies containing rubber components used for aerospace purposes

9、 unless amended by other contractual requirements. 1.2 The packaging specified not only ensures adequate identification of the components, but also forms an integral part of the controlled storage and inspection procedure (see British Standard F68). 2 Reference This standard makes reference to the f

10、ollowing standards publication. F 68, Controlled storage of vulcanized rubbers for use in aerospace applications. The latest issue of this standard shall be used. NOTEThe latest revision of an Aerospace Series standard is indicated by a prefix number. 3 Packaging 3.1 General 3.1.1 As soon as possibl

11、e after curing, and except as provided in3.1.2, components shall be individually enclosed in hermetically sealed envelopes or in hermetically sealed pockets in a multiple envelope provided that they can be removed without affecting the sealing of the remainder of the components in the package. 3.1.2

12、 Components which cannot conveniently be accommodated in envelopes shall be suitably enclosed or wrapped so as to prevent free access of air. 3.1.3 Packaging shall be accomplished under conditions of low relative humidity i.e.not exceeding65% and under conditions which will also ensure freedom from

13、contamination by dust, oil, grease etc. 3.1.4 Components shall be free from strain. Large components shall be adequately supported and no part shall be tied or tagged. NOTERings of large internal diameter may be formed into three equal superimposed loops so as to avoid creasing or twisting. It will

14、be noted that this condition is impossible to attain in two loops. 3.1.5 When it is necessary for components to be packed in assembly sets such components shall be retained in their original identifying envelopes and the whole shall be inserted to the required quantity in the main package. 3.2 Dimen

15、sions of envelopes. The preferred sizes of envelopes are55mm,100mm,150mm,205mm and 255mm square. 3.3 Packaging materials 3.3.1 Preference shall be given to the use of heat sealable opaque materials. Suitable materials are polyethylene coated kraft paper, aluminium foil/paper/polyethylene laminate an

16、d opaque polyethylene film. Polyvinylchloride (PVC) film shall not be used. If for any reason a transparent or translucent material is used, it shall be over wrapped with an opaque material. Polyethylene film used alone should be of a nominal thickness of not less than754m. 3.3.2 When it is known th

17、at relative humidity in storage will be above75%, packaging with aluminium foil/paper/polyethylene laminate is required to ensure protection from ingress of moisture. 4 Identification on packaging Every package or every pocket in a multiple envelope shall be marked with at least the following inform

18、ation which shall be visible from the outside of the package with the seal unbroken: a) part number; b) material specification number and/or polymer description; c) quarter and year of cure (e.g.3Q81); d) life grouping in accordance with the requirements of F68; e) quantity in package; f) batch numb

19、er or release/certification number; g) manufacturers identity. 5 Identification by colour code Colour coding shall be applied to components only if specifically requested on the drawing or order. The form of code and method of application shall be agreed between the user and the supplier.3F 69:1979

20、BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are

21、updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Brit

22、ishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest

23、 editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

24、 have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are a

25、lso available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these a

26、nd other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and

27、Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of neces

28、sary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.