BS 3G 100-2 2-1972 Specification for general requirements for equipment for use in aircraft - All equipment - Magnetic influence《飞机设备的一般要求规范 第2部分 各种设备 第2节 磁影响》.pdf

1、BRITISH STANDARD: AEROSPACE SERIES BS 3G. 100-2.2: 1972 Specification for General requirements for equipment in aircraft Part 2: All equipment Section 2: Magnetic influence UDC 629.7.05/.06:538.6BS 3G. 100-2.2:1972 This British Standard, having been approved by the AerospaceIndustry Standards Commit

2、tee, was published underthe authority of the Executive Board of the Institutionon 14 June 1972 BSI 03-1999 The following BSI references relate to the work on this standard: Committee reference ACE/41 Draft for comment 70/26881 ISBN 0 580 07153 7 Foreword This British Standard is part of a composite

3、standard in the Aerospace Series of British Standards that specifies general requirements for equipment in aircraft. An introduction to the complete British Standard is given in British Standard 3G.100-0. This section of British Standard 3G.100 supersedes the magnetic influence requirements specifie

4、d in Clauses 227 and 228 of British Standard 2G.100-2. It details limiting requirements of magnetic influence of aircraft equipment upon magnetic compasses and similar sensors in terms of “compass safe distance”. NOTEInformation concerning metric (SI) units is given in BS 350, “Conversion factors an

5、d tables”, and BS 3763, “The International System of units (SI)”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity

6、 from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1and2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the insi

7、de front cover. Amendments issued since publication Amd. No. Date Comments 2791 May 1979 Indicated by a sideline in the marginBS 3G. 100-2.2:1972 BSI 03-1999 i Contents Page Foreword Inside front cover 1 Scope 1 2 Definitions 1 3 Design requirements 1 4 Measurement of compass safe distance 1 5 Speci

8、al measurements 2ii blankBS 3G. 100-2.2:1972 BSI 03-1999 1 1 Scope This British Standard defines, specifies requirements for and describes a test to determine the compass safe distance of equipment in aircraft. It should also be read in conjunction with British Standard 3G.100-0. 2 Definitions For t

9、he purposes of this British Standard the following definition applies: 1) Compass safe distance. The minimum distance from a magnetic compass at which an item of equipment may be placed to limit the compass deviation to a stated value under all conditions of operation. 3 Design requirements 3.1 Equi

10、pment shall be so designed that the external magnetic fields produced by it under all conditions of operation are as small as is practicable. 3.2 The designer shall declare for each type of equipment the compass safe distance, determined in the manner described in Clause 4. 3.3 When there is a requi

11、rement for a specific minimum compass safe distance it shall be specified in the relevant equipment specification. It is recommended that the compass safe distance for other items of equipment likely to be mounted near a magnetic compass should not exceed the following values. 4 Measurement of compa

12、ss safe distance 4.1 It is not permissible for the equipment under test to be demagnetized before measuring the compass safe distance. The relevant equipment specification may however require, in special circumstances, the equipment to be demagnetized and then remagnetized to approximately15A/m. 4.2

13、 The compass safe distance shall be measured from the pivot of the reference magnetometer or compass to the nearest point on the surface of the equipment under test in the manner described below. 4.3 Measurements shall be made in a uniform magnetic field. If the horizontal component of this field ha

14、s a value outside the limits13to 16A/m, then the compass safe distance shall be the distance at which the equipment under test produces the deviation D ccalculated by the following equation: where D is the compass deviation at the safe distance in a horizontal field of 14.4A/m and is defined by this

15、 specification as one degree. Where the horizontal field is of such a value that the calculation above is necessary, all other absolute statements of a deviation in this specification shall be similarly adjusted. The test area should be marked out with magnetic NS and EW lines, and a suitable magnet

16、ometer placed at the intersection of these lines. This magnetometer, which may be a compass, shall be capable of being read to an accuracy of and possess a corresponding sensitivity. 4.4 The equipment under test shall be placed on the EW line at a distance from the magnetometer that induces a deviat

17、ion of approximately2. Experiments shall be made to determine the combination of attitude and degree of energization that gives the maximum deviation of the magnetometer. This combination shall be maintained while the equipment is moved outward along the EW line until the magnetometer deviation is a

18、pproximately . Type of equipment Distance to produce a 1 deflection mm Electrical 300 Non-electrical 125 D c D 14.4 Actual field strength - = 1 / 5BS 3G. 100-2.2:1972 2 BSI 03-1999 4.5 From the accurate readings taken at intervals during this movement, a curve shall be plotted showing magnetometer d

19、eviation against distance (see 4.2). As a check on experimental error, a further curve shall also be plotted to correspond with an inward movement of the equipment. 4.6 The two curves should be substantially coincident and should be used to establish the distance at which one degree deviation of the

20、 magnetometer is experienced. The distance shall be the declared compass safe distance for the equipment. 5 Special measurements 5.1 When required by the individual specification an additional compass safe distance shall also be declared for a deviation of . This distance may be extrapolated from th

21、e curves required by 4.5. 5.2 The compass safe distance of equipment that produces a significant directional magnetic effect shall be measured along other axes defined by the relevant specification and declared. 1 / 83 blankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | |

22、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsibl

23、e for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments

24、 or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found o

25、n the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications

26、 should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI pro

27、vides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel

28、: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Cop

29、yright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted

30、 in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.