1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 4092 : Part 1 : 1996 I
2、CS 91.090 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Domestic front entrance gates Part 1. Specification for metal gatesThis British Standard, having been prepared under the direction of the Sector Board for Building and Civil Engineering, was published under the authorit
3、y of the Standards Board and comes into effect on 15 December 1996 BSI 1996 First published 1996 Second edition December 1996 The following BSI references relate to the work on this standard: Committee reference B/201/2 Draft for comment 95/107593 DC ISBN 0 580 25884 X BS 4092 : Part 1 : 1996 Amendm
4、ents issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee B/201, Fences and gates, to Subcommittee B/201/2, Fences Steel, upon which the following bodies were represented: A
5、ssociation of Security Consultants British Iron and Steel Producers Association Cold Rolled Sections Association Country Landowners Association Countryside Commission County Surveyors Society Department of the Environment (Property Holdings) Electricity Association European Fencing Industry Associat
6、ion Fencing Contractors Association Institute of Leisure and Amenity Management National Fencing Training Authority Royal Institute of Chartered Surveyors Scottish Office (Agriculture and Fisheries Department)BS 4092 : Part 1 : 1996 BSI 1996 i Contents Page Foreword ii Specification 1 Scope 1 2 Norm
7、ative references 1 3 Information and requirements to be agreed and to be documented 1 4 Gate size 1 5 Materials 1 6 Construction 1 7 Dimensions of components 2 8 Hanging and latching fittings 2 9 Protective treatment 2 10 Marking 2 Annex A (informative) Information to be obtained for the purpose of
8、an order or an enquiry 3 List of references Inside back coverii BSI 1996 BS 4092 : Part 1 : 1996 Foreword This Part of BS 4092 has been prepared under the direction of Technical Committee B/201, Fences and gates. It supersedes BS 4092 : Part 1 : 1966, which is withdrawn. Part 2 was withdrawn in 1995
9、. This Part of the standard deals with domestic metal gates such as those commonly used as single or double front entrance gates for a house or a garage. The specification is aimed at setting down functional requirements and is in no way concerned with design apart from such requirements. This revis
10、ion of BS 4092 : Part 1 brings previously specified dimensions in line with current metric sizing and also updates the references. There are no technical changes. Compliance with a British Standard does not itself confer immunity from legal obligations. BSI 1996 1 BS 4092 : Part 1 : 1996 Specificati
11、on 1 Scope This Part of BS 4092 specifies dimensional, material and constructional requirements for domestic front entrance gates. It applies to metal front entrance gates of tubular frame, mild steel or wrought iron flat frame constructions. It states certain functional requirements to which the de
12、sign should conform, but does not specify detailed design. Annex A lists the information to be obtained for the purpose of an order or an enquiry. 2 Normative references This Part of BS 4092 incorporates, by dated or undated reference, provisions from other publications. These normative references a
13、re made at the appropriate places in the text and the cited publications are listed on the inside back cover. For dated references, only the edition cited applies; any subsequent amendments to or revisions of the cited publication apply to this Part of BS 4092 only when incorporated in the reference
14、 by amendment or revision. For undated references, the latest edition of the cited publication applies, together with any amendments. 3 Information and requirements to be agreed and to be documented The following items to be agreed between the contracting parties, which are specified in the clauses
15、referred to, shall be fully documented. Both the definitive requirements specified throughout the standard and the following documented items shall be satisfied before a claim of compliance can be made and verified. a) Gate size for rising drives (see 4.1). b) Panel infilling (see 7.2). c) Protectiv
16、e treatment (see clause 9). NOTE. See also annex A. 4 Gate size 4.1 Height The top of the gate frame shall be a minimum of 0.9 m above the ground when hung with a ground clearance of not more than 50 mm. For rising drives, where extra clearance may be required, the minimum height and maximum clearan
17、ce shall be agreed between the manufacturer and purchaser. 4.2 Width For new works, the gate width between the posts or piers shall be one of the values given in table 1. Table 1. Width of gates Type of gate Width between posts or piers (m) Single gates 0.9 1.0 1.1 Double gates 2.3 2.4 2.7 For doubl
18、e gates the leaves shall be of equal width. NOTE. For existing front entrance gateways, the widths given in table 1 are preferred. 4.3 Clearance The construction of the gate shall provide an effective clear opening that does not reduce the width given in 4.2 by more than 75 mm for single gates and 1
19、00 mm for double gates. 5 Materials Gates shall be constructed of mild steel or wrought iron conforming to one of the following: a) mild steel of square or flat section conforming to BS EN 10025 : 1993, minimum grade SJ 275; b) mild steel tube conforming to BS 1387; c) mild steel structural hollow s
20、ections conforming to BS 6363. 6 Construction 6.1 Frames Gates shall have a continuous framework. Gate frames shall be truly square, and shall be welded all round at junctions in accordance with BS 5135. 6.2 Infilling Straight or shaped bars shall be welded all round at junctions with the frame in a
21、ccordance with BS 5135. 6.2.1 Scrollwork shall be fully welded along the top side at junctions in accordance with BS 5135. 6.2.2 Tubular or hollow section infilling shall be welded all round at junctions in accordance with BS 5135. 6.3 Workmanship Gates shall have no rough, sharp or jagged edges. We
22、lding slag shall be removed.2 BSI 1996 BS 4092 : Part 1 : 1996 1) Marking BS 4092 : Part 1 : 1996 on or in relation to a product represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accurac
23、y of the claim is solely the claimants responsibility. Such a declaration is not to be confused with third party certification of conformity, which may also be desirable. 7 Dimensions of components 7.1 Framework The minimum dimensions of the components in the frame shall be as follows. a) Except for
24、 gates 2.7 m wide, a solid rectangular section shall have minimum dimensions 20 mm3 10 mm. For gates 2.7 m wide the minimum section shall be 25 mm3 10 mm. b) A solid square section shall have minimum dimensions 16 mm3 16 mm. c) A tubing or hollow section shall have a minimum thickness of 2.0 mm, and
25、 either: 1) a minimum outside diameter of 20 mm for tube or circular hollow sections; or 2) minimum dimensions 20 mm3 20 mm for square hollow sections. 7.2 Infilling The minimum dimensions of the components used in the infill shall be as follows. a) Straight or shaped bars shall have minimum dimensi
26、ons 12 mm3 12 mm or 14 mm3 14 mm, or a minimum diameter of 12 mm. b) Ornamental scrollwork shall have minimum dimensions 13 mm3 3 mm. c) Tubing or hollow section shall have a minimum thickness of 1.8 mm. d) Panel infilling other than that in a), b) or c) shall be agreed between the purchaser and the
27、 supplier. NOTE. Other types of infilling such as mesh may be used. 8 Hanging and latching fittings 8.1 Hanging fittings Hanging fittings shall be either welded all round or shall be bolted to the gate frame. The clearance between the pins and the eyes shall be such as to provide a reasonable fit. T
28、he material forming any eye for the hinge shall have minimum dimensions of 20 mm3 5 mm formed into an eye, or 25 mm3 10 mm holed to fit the pin. Hinge pins shall be not less than 12 mm in diameter. NOTE. The hinge pin fittings should be reversible, so that the top hinge may be installed with the hin
29、ge pin pointing downwards. This should stop the gate from being lifted off its hinges once installed. 8.2 Fastenings The fastenings shall be such that, when closed, the gates are held securely in position. If flat latch bars are used, they shall be not less than 25 mm3 6 mm. 8.3 Slam plates and drop
30、 bolts Double gates shall be provided with a slam plate of minimum thickness 6 mm. One leaf shall be provided with a drop bolt of minimum diameter 12 mm with an adequate ground socket. NOTE. The provision of a centre stop should be considered where gates open onto public areas. 9 Protective treatmen
31、t The protective treatment shall be agreed between the purchaser and the supplier. All rust and loose scale shall be removed from the surfaces before protective treatment. Protective treatment shall be one of the following. a) One works coat of steel priming paint conforming to BS 5493. b) A metal c
32、oat conforming to BS 2569 : Part 1. c) Hot dip galvanizing conforming to BS 729. NOTE 1. This standard does not specify the finishing coats; these should be applied after erection. NOTE 2. The protective treatment specified in item a) is not intended to serve as a finishing coat. Immediately after e
33、rection it should be rubbed down and made good. It is also recommended that a further coat of primer should be applied to ensure adequate coverage of the profile prior to application of the finishing coats. 10 Marking Metal gates shall be legibly marked by a stencil, or labelled with an adhesive lab
34、el, with the following information: a) the manufacturers name and/or trade mark; b) the number and date of this standard, i.e. BS 4092 : Part 1 : 1996. 1)BS 4092 : Part 1 : 1996 BSI 1996 3 Annex Annex A (informative) Information to be obtained for the purpose of an order or an enquiry The following
35、information should be obtained by the supplier in connection with any order or enquiry for domestic metal gates conforming to this standard. a) The width of the opening between the pillars or posts. The width of the gate required should not be stated; this should be determined by the manufacturer in
36、 accordance with the provisions of this standard. b) The height and maximum clearance of the gate for rising drives, if the manufacturers standard designs are not required. c) Details of infilling, if the manufacturers standard designs are not required. d) Details of the protective treatment require
37、d. e) For a single gate, whether it is to be hung from the left hand pillar when viewed from the outside (left hand), or from the right hand pillar (right hand). f) For double gates, whether the latch is fixed on the right hand gate when viewed from the outside and whether a centre stop is required.
38、 g) Which of the following fittings are required: 1) for building into brickwork; 2) for screwing into wooden posts; 3) the size and type of fittings for bolting through concrete, wooden or metal posts. It is not advisable to order gates to fit existing fittings as it is not generally possible, with
39、 the facilities available on site, to measure the position of the pins with sufficient accuracy. It is preferable to remove existing fittings and to re-set the fittings provided with the gate.4 blank BSI 1996 BS 4092 : Part 1 : 1996 List of references (see clause 2) Normative references BSI publicat
40、ions BRITISH STANDARDS INSTITUTION, London BS 729 : 1971 Specification for hot dip galvanized coatings on iron and steel articles BS 1387 : 1985 Specification for screwed and socketed steel tubes and tubulars and for plain end steel tubes suitable for welding or for screwing to BS 21 pipe threads BS
41、 2569 Specification for sprayed metal coatings BS 2569 : Part 2 : 1965 Protection of iron and steel against corrosion and oxidation at elevated temperatures BS 6363 : 1983 Specification for welded cold formed steel structural hollow sections BS 5135 : 1984 Specification for arc welding of carbon and
42、 carbon manganese steels BS 5493 : 1977 Code of practice for protective coating of iron and steel structures against corrosion BS EN 10025 : 1993 Hot rolled products of non-alloy structural steels. Technical delivery conditionsBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | |
43、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body respons
44、ible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendme
45、nts or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be foun
46、d on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publicati
47、ons should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI
48、provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre.
49、Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retri
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1