BS 4193-22-1996 Hardmetal insert tooling Classification and designation of approximate chip control zones for indexable inserts with chipbreakers《镶硬质合金刀具 第22部分 带断屑器的分度刀片近似切屑控制范围分类和.pdf

1、BRITISH STANDARD BS 4193-22: 1996 ISO 10910: 1995 Hardmetal insert tooling Part 22: Classification and designation of approximate chip control zones for indexable inserts with chipbreakers ICS 25.100BS 4193-22:1996 This British Standard, having been prepared under the directionof the Engineering Sec

2、torBoard, was published underthe authority of the Standards Board and comes into effect on 15 September 1996 BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference MTE/18 Draft for comment 92/74307 DC ISBN 0 580 26318 5 Committees responsible for this Briti

3、sh Standard The preparation of this British Standard was entrusted to Technical Committee MTE/18, Tools, tips and inserts for cutting applications, upon which the following bodies were represented: British Engineers Cutting Tools Association British Hardmetal Association Co-opted members Amendments

4、issued since publication Amd. No. Date CommentsBS 4193-22:1996 BSI 11-1998 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative references 1 3 Graph 1 4 Diagrams 1 5 Cutting test 1 6 Classification 3 Figure 1 2 Figure 2 4 List of references Inside back

5、 coverBS 4193-22:1996 ii BSI 11-1998 National foreword This British Standard has been prepared by Technical Committee MTE/18 and is identical with ISO 10910:1995 Classification and designation of approximate chip control zones for indexable inserts with chipbreakers, prepared by ISO/TC 29, Small too

6、ls, of the International Organization for Standardization (ISO). The Technical Committee has reviewed the provisions of ISO 683-1:1987, ISO3002-1:1982, ISO 3002-3:1984 and ISO 3685:1993 to which normative reference is made in the text, and has decided that they are acceptable for use in conjunction

7、with this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publi

8、cation referred to Corresponding British Standard ISO 1832:1991 BS 4193 Hardmetal insert tooling Part 1:1993 Specification for designation of indexable inserts for cutting tools (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, a

9、n inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.BS 4193-22:1996 BSI 11-1998 1 1 Scope This International Standard establishes a graph format used

10、 to develop diagrams depicting chipbreaker indexable insert performance. Performance results may be derived from the cutting test described in clause 5. Classification zones are established and coded in this International Standard. Suppliers of chipbreaker insert products may classify their products

11、 using the code of the zone within which the primary use of their product is indicated. It is important to acknowledge that the relationships established by diagrams developed according to this International Standard may vary from one work material to another, as well as with other machining variabl

12、es, and that it is not the purpose of this International Standard to serve as a specific guide to the practical application of chipbreaker insert products, but rather grant the user a sort of pre-selection, on a general level, that will allow him to look at only those items that have the best chance

13、 of satisfying his needs. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties t

14、o agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 683-1:1987, Heat-treatable steels, alloy st

15、eels and free-cutting steels Part 1: Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products. ISO 1832:1991, Indexable inserts for cutting tools Designation. ISO 3002-1:1982, Basic quantities in cutting and grindingPart 1: Geometry of the active part of cutting t

16、ools General terms, reference systems, tool and working angles, chip breakers. ISO 3002-3:1984, Basic quantities in cutting and grindingPart 3: Geometric and kinematic quantities in cutting. ISO 3685:1993, Tool-life testing with single-point turning tools. 3 Graph The axes of the graph format (see F

17、igure 1) shall be the feed (according to ISO 3002-3) and the depth of cut (according to ISO 3002-3). The limits of the feed and depth of cut shall be = 0,025 mm/rev to 2,5 mm/rev and a p= 0,1 mm to 16 mm. 4 Diagrams The graph (see Figure 1) may be used to develop diagrams depicting chipbreaker inser

18、t performance resulting from the standard cutting test. The diagram shall be constructed by connecting points on the graph and shall represent an area within which chips are controlled. Referring to chips as acceptable and/or unacceptable is not recommended due to the varied opinions from industry t

19、o industry. Recommended terms are: controlled and uncontrolled. Also, it would be acceptable to use chip form codes established in ISO3685:1993, annex G, or to show the actual chips generated from the cutting test. 5 Cutting test The cutting test developed to establish chipbreaker insert performance

20、 and subsequent classification is described as follows: Operation: external (outside diameter) turning. Cutting edge angle (according to ISO 3002-1): k r= 75 for insert shape S or k r= 90 to 95 for insert shapes C, D, T and V. Workpiece material: C 45 (according to ISO683-1:1987). Materials other th

21、an C 45 shall be indicated in the insert performance diagram. Normalized:180 HB to 200 HB. Cutting Speed (according to ISO 3002-1): appropriate to cutting material. Cutting speed shall be indicated in the insert performance diagram. Minimum diameter of parts:100 mm.BS 4193-22:1996 2 BSI 11-1998 Figu

22、re 1BS 4193-22:1996 BSI 11-1998 3 6 Classification The term classification used in this International Standard is defined as the common ground on which suppliers can specify the primary use of their chipbreaker inserts. The range of use of a chipbreaker insert on the other hand is shown by a diagram

23、 generated on the graph, Figure 1. The diagram (see Figure 2) is divided into 6 zones of classification. It is the responsibility of the supplier to classify his chipbreaker insert with the code of the zone that best represents the intended primary use of the insert being classified (only one letter

24、 shall be used). While the zones are specified by this International Standard, it should be noted that the decision to create the zones in this manner is arbitrary. Each zone has its own code, either A, B, C, D, E or F which may be used at the discretion of the chipbreaker insert supplier. However,

25、the classification codes defined here shall not be used as an addition to the existing insert identification systems (see ISO 1832) or as commercial designations for chipbreaker insert products. NOTE 1It is common practice in industry that manufacturers classify inserts with certain geometry feature

26、s in “family geometry groups”, designated by letters, numbers or a combination of both after the standard designation of the insert, e.g.: CNMG 120408 XX Although those inserts (“XX”) are grouped to belong to the same geometry family the chip control features can be different, depending on the size

27、of the insert and the size of the corner radii. This International Standard provides the possibility of giving information about chip breaking capabilities of insert sizes within a certain geometry family, for instance as follows: Insert designation Chip control zone CNMG 120404 XX A CNMG 160616 XX

28、C . .BS 4193-22:1996 4 BSI 11-1998 Figure 2BS 4193-22:1996 BSI 11-1998 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

29、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level

30、. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be gra

31、teful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating serv

32、ice called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for int

33、ernational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its

34、Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments

35、and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications

36、of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission f

37、rom BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.