BS 4427-10-1976 Methods of test for sodium tripolyphosphate (pentasodium triphosphate) and sodium pyrophosphate (tetrasodium pyrophosphate) for industrial use - Determination of to.pdf

1、BRITISH STANDARD BS 4427-10: 1976 ISO 3357:1975 Methods of test for Sodium tripolyphosphate (pentasodium triphosphate) and sodium pyrophosphate (tetrasodium pyrophosphate) for industrial use Part 10: Determination of total phosphorus (V) oxide content: quinoline phosphomolybdate gravimetric method U

2、DC 661.833.456 + 661.833.458:546.33185:543.062:546.185 31BS4427-10:1976 This British Standard, having been prepared under the directionof the Chemicals IndustryStandards Committee, was published under the authorityof the Executive Boardon 30 June1976 BSI 11-1999 The following BSI references relate t

3、o the work on this standard: Committee reference CIC/25 Draft for comment 74/51835 DC ISBN 0 580 09193 7 Co-operating organizations The Chemicals Industry Standards Committee, under whose supervision this British Standard was prepared, consists of representatives of the following Government departme

4、nts and scientific and industrial organizations: Association of Fatty Acids Distillers Chemical Industries Association* Department of Health and Social Security Department of Industry Chemicals and Textiles Division Department of Industry Laboratory of the Government Chemist* Fertiliser Manufacturer

5、s Association Limited* Ministry of Agriculture, Fisheries and Food National Sulphuric Acid Association Royal Institute of Public Health and Hygiene Soap and Detergent Industry Association Society of Analytical Chemistry The Government department and industrial organizations marked with an asterisk i

6、n the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: British Pharmacopoeia Commission Campden Food Preservation Research Association Flour Milling and Baking Research Association Institute of Metal Finishin

7、g National Association of Soft Drink Manufacturers Society of Chemical Industry Textile Institute Amendments issued since publication Amd. No. Date of issue CommentsBS4427-10:1976 BSI 11-1999 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 Scope and field of application 1

8、 2 Principle 1 3 Reagents 1 4 Apparatus 1 5 Procedure 1 6 Expression of results 2 7 Test report 2 Annex ISO publications relating to condensed sodium phosphates for industrial use 3BS4427-10:1976 ii BSI 11-1999 Foreword This British Standard has been prepared under the authority of the Chemicals Ind

9、ustry Standards Committee in order to provide methods for the analysis of sodium tripolyphosphate and sodium pyrophosphate. For some years the United Kingdom has participated in the work of preparing methods of test applicable to sodium tripolyphosphate and sodium pyrophosphate for industrial use, o

10、rganized by Subcommittee6 (formerly Working Group7) “Phosphoric Acid and Condensed Phosphates” of Technical Committee47 “Chemistry” of the International Organization for Standardization (ISO). As international agreement is reached on the methods, it is proposed to publish them as Parts of this Briti

11、sh Standard. This Part is identical with ISO3357 “Sodium tripolyphosphate and sodium pyrophosphate for industrial use Determination of total phosphorus (V) oxide content Quinoline phosphomolybdate gravimetric method”. For the purposes of this Part of this British Standard, the text of ISO3357given i

12、n this publication should be modified as follows: Terminology. The words “British Standard” should replace “International Standard” wherever they appear. The decimal point should replace the decimal comma wherever it occurs. Cross references. The references to International Standards should be repla

13、ced by references to British Standards as follows: Additional information Water of satisfactory purity (see clause 3) is specified in BS3978 “Water for laboratory use”. In the UnitedKingdom, the commercially available reagent grade of hydrochloric acid (see 3.1) has a density of approximately1.18g/m

14、l, is about36% (m/m) or approximately11N solution. A grade of quinoline which does not require purification by being freshly distilled (see 3.2.4) is commercially available in the United Kingdom. This standard specifies methods of test only and should not be used or quoted as a specification definin

15、g limits of purity. Reference to the standard should be in a form of words indicating that the methods of test used conform to the requirements of BS4427. Reference to InternationalStandard Appropriate British Standard ISO/R 850 BS 4427-1 ISO/R 851 BS 4427-2 ISO/R 852 BS 4427-3 ISO/R 853 BS 4427-4 I

16、SO 2996 BS 4427-5 ISO 2998 BS 4427-8 ISO 2999 BS 4427-6 ISO 3000 BS 4427-7 ISO 3357 BS 4427-10 ISO 3358 BS 4427-11 a a In course of preparationBS4427-10:1976 BSI 11-1999 iii A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are resp

17、onsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, pages1to 3 and a back cover. This standard has been updated (see copyrigh

18、t date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.iv blankBS4427-10:1976 BSI 11-1999 1 1 Scope and field of application This International Standard specifies a gravimetric method using quinoline phosphomolybdate for the determin

19、ation of the total phosphorus(V) oxide content of sodium tripolyphosphate (pentasodium triphosphate) and sodium pyrophosphate (tetrasodium diphosphate) for industrial use. 2 Principle Hydrolysis of a test portion by prolonged boiling in the presence of hydrochloric acid. Precipitation of phosphates

20、in the form of quinoline phosphomolybdate in the presence of acetone. Filtration, washing, drying and weighing of the precipitate. 3 Reagents During the analysis, use only reagents of recognized analytical reagent grade and only distilled water or water of equivalent purity. 3.1 Hydrochloric acid, a

21、pproximately1,19g/ml, about38% (m/m) or approximately12N solution. 3.2 Citromolybdate reagent 3.2.1 Dissolve70g of sodium molybdate dihydrate (Na 2 MoO 4 .2H 2 O) in150ml of water. 3.2.2 Dissolve60g of citric acid monohydrate (C 6 H 8 O 7 .H 2 O) in150ml of water and add85ml of nitric acid solution,

22、 approximately1,40g/ml, about68% (m/m) or approximately14N solution. 3.2.3 Add, with mixing, solution 3.2.1 to solution3.2.2. 3.2.4 Add35ml of nitric acid solution, approximately1,40g/ml, about68% (m/m) or approximately14N solution, followed by5ml of pure quinoline, recently distilled, to100ml of wa

23、ter. 3.2.5 Pour solution 3.2.4 into solution 3.2.3 and mix. Allow to stand for at least12h (for example, overnight) and filter through a sintered glass filter of porosity grade P10 (pore size index4to10m). Store this solution protected from light in a well-stoppered flask. 3.2.6 Add280ml of acetone

24、to solution 3.2.5 and dilute to1000ml with water. Do not keep this solution for more than1week. Store under the same conditions as solution 3.2.5. 4 Apparatus Ordinary laboratory apparatus and 4.1 Filter crucible, with sintered glass disk, porosity grade P10 (pore size index4to10m). 4.2 Electric ove

25、n, capable of being controlled at250 10 C. 5 Procedure WARNING Acetone is very flammable and must be handled only inside a well-ventilated fume cupboard, in the absence of flames. 5.1 Test portion Weigh, to the nearest0,0002g, 1g of the test sample, taking care to avoid any gain or loss of moisture.

26、 5.2 Blank test Carry out a blank test at the same time as the determination, following the same procedure and using the same quantities of all the reagents as used in the determination. 5.3 Determination 5.3.1 Preparation of the test solution Place the test portion (5.1) in a250ml flask with ground

27、 neck, dissolve in about50ml of water, add20ml of the hydrochloric acid solution (3.1), fit a reflux condenser on the flask and boil for at least20min. Cool, transfer the solution quantitatively to a1000ml one-mark volumetric flask, dilute to the mark and mix. Prepare this solution at the time of us

28、e and filter if necessary. NOTEIf hydrochloric acid of the concentration indicated in the list of reagents is not available, solutions of lower concentration may be used, by adding the corresponding stoichiometric quantity of HCl. 5.3.2 Precipitation and filtration Take25,0ml of the test solution (5

29、.3.1) and place in a400ml beaker. Dilute to100ml and add100ml of the citromolybdate reagent (3.2). Cover the beaker with a clock glass, warm inside a fume cupboard, on a hot-plate, until its contents reach75 5 C and maintain at this temperature for about30s. (Do not use a flame and do not mix, eithe

30、r during the addition of the reagent or during the heating, so as to avoid the formation of clots.) Allow to cool to ambient temperature, stirring three or four times with a glass rod during cooling.BS4427-10:1976 2 BSI 11-1999 Heat the filter crucible (4.1) in the oven (4.2), controlled at250 10 C,

31、 for15min, allow to cool in a desiccator containing silica gel in good condition and weigh to the nearest0,0001g. Decant the liquid through the crucible and wash the precipitate six times, by decantation, using about30ml of water each time. Transfer all the precipitate to the filter crucible by mean

32、s of a jet of water from a wash bottle. Then wash the precipitate four times, removing each portion of wash water with the aid of a vacuum pump. 5.3.3 Drying and weighing Place the filter crucible in the oven (4.2), controlled at250 10 C, for15min starting from the stabilization of temperature. Allo

33、w to cool for not more than30min in the desiccator containing silica gel in good condition and weigh to the nearest0,0001g. 6 Expression of results The total phosphorus(V) oxide (P 2 O 5 ) content, expressed as a percentage by mass, is given by the formula: where m 0 is the mass, in grams, of the te

34、st portion(5.1); m 1 is the mass, in grams, of precipitate obtained during the determination (5.3.3); m 2 is the mass, in grams, of precipitate obtained during the blank test (5.2); is the ratio between the volume of the test solution and the aliquot portion taken for the determination; 0,032 07is t

35、he factor for conversion of quinoline phosphomolybdate to phosphorus(V) oxide. 7 Test report The test report shall include the following particulars: a) the reference of the method used; b) the results and the method of expression used; c) any unusual features noted during the determination; d) any

36、operation not included in this International Standard, or regarded as optional. 1 000 25 -BS4427-10:1976 BSI 11-1999 3 Annex ISO publications relating to condensed sodium phosphates for industrial use Sodium pyrophosphate (tetrasodium diphosphate) ISO 2999, Estimation of pyrophosphate content Potent

37、iometric method. Sodium tripolyphosphate (pentasodium triphosphate) ISO/R 850, Determination of matter insoluble in water. ISO/R 851, Measurement of pH Potentiometric method. ISO 3000, Estimation of tripolyphosphate content Tris(ethylenediamine) cobalt(III) chloride gravimetric method. Sodium pyroph

38、osphate and sodium tripolyphosphate (tetrasodium diphosphate and pentasodium triphosphate) ISO/R 852, Determination of iron content 2,2-Bipyridyl spectrophotometric method. ISO/R 853, Determination of loss on ignition. ISO 2996, Determination of particle size distribution by mechanical sieving. ISO

39、2998, Determination of orthophosphate content Photometric method using the reduced molybdophosphate. ISO 3357, Determination of total phosphorus(V) oxide content Quinoline phosphomolybdate gravimetric method. ISO 3358, Separation by column chromatography and determination of the different phosphate

40、forms 1) . 1) At present at the stage of draft.BS 4427-10: 1976 ISO3357:1975 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the internationa

41、l level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would b

42、e grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating servic

43、e called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for internation

44、al standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical

45、 Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive sub

46、stantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international

47、standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does no

48、t preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.