BS 4442-1-1969 Specification for lathe spindle noses and faceplates - Types A and Camlock《车床轴头及面板规范 第1部分 A 式和卡姆洛克式》.pdf

1、BRITISH STANDARD BS 4442-1: 1969 Specification for Lathe spindle noses and faceplates Part1: Type “A” and “Camlock”BS4442-1:1969 This British Standard, having been approved by the MechanicalEngineering IndustryStandards Committee,was published underthe authority of the Executive Board on 31March1969

2、 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference MEE/6 Draft for comment66/11048 ISBN 0 580 05178 1 Co-operating organizations The Mechanical Engineering Industry Standards Committee, under whose supervision this British Standard was prepared, consis

3、ts of representatives from the following Government departments and scientific and industrial organizations: The Government departments and scientific and industrial organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entru

4、sted with the preparation of this British Standard: Associated Offices Technical Committee Institution of Civil Engineers Association of Consulting Engineers Institution of Gas Engineers Association of Mining Electrical and Institution of Heating and Ventilating Mechanical Engineers Engineers Board

5、of Trade Institution of Mechanical Engineers* British Chemical Plant Manufacturers Institution of Mechanical Engineers Association (Automobile Division) British Compressed Air Society Institution of Production Engineers* British Electrical and Allied Manufacturers Locomotive and Allied Manufacturers

6、 Association* Association of GreatBritain British Gear Manufacturers Association London Transport Board British Internal Combustion Engine Machine Tool Trades Association* Manufacturers Association Ministry of Defence British Mechanical Engineering Federation Ministry of Defence, Army Department* Br

7、itish Pump Manufacturers Association Ministry of Power British Steel Industry Ministry of Public Building and Works* Crown Agents for Oversea Governments and Ministry of Technology Administrations Ministry of Technology National Department of Employment and Productivity Engineering Laboratory* (H.M.

8、Factory Inspectorate) Ministry of Transport Electricity Council, the Central Electricity National Coal Board Generating Board and the Area Boards in National Physical Laboratory (Ministry of England and Wales Technology) Engineering Equipment Users Association Radio Industry Council Gas Council Roya

9、l Institute of British Architects Institute of Marine Engineers Association of Supervisory Staffs Executives Production Engineering Research Association and Technicians Society of Motor Manufacturers and Traders Ministry of Defence, Air Force Department Limited Ministry of Defence, Navy Department T

10、rades Union Congress National Federation of Engineers Tool Manufacturers Amendments issued since publication Amd. No. Date CommentsBS4442-1:1969 BSI 01-2000 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 Scope 1 2 Dimensions and tolerances 1 Figure 1 Spindle noses, Types

11、 A 1and A 2 2 Figure 2 Faceplates, Type A 4 Figure 3 Spindle noses, Type Camlock 5 Figure 4 Cams, Type Camlock 7 Figure 5 Studs, Type Camlock 9 Figure 6 Faceplates, Type Camlock 10 Figure 7 Type Camlock accessories 12 Table 1 Spindle noses, Types A 1and A 2 3 Table 2 Faceplates, Type A 4 Table 3 Spi

12、ndle noses, Type Camlock 6 Table 4 Cams, Type Camlock 8 Table 5 Studs, Type Camlock 9 Table 6 Faceplates, Type Camlock 11 Table 7 Type Camlock accessories 12BS4442-1:1969 ii BSI 01-2000 Foreword This standard makes reference to the following British Standard: BS 1916, Limits and fits for engineering

13、. BS 1916-1, Limits and tolerances. In view of the measure of agreement that has been achieved internationally on the dimensional standardization of lathe spindle noses and faceplates, it has been considered opportune to prepare a British Standard implementing the recommendations of Technical Commit

14、tee39 Machine Tools of the International Organization for Standardization (ISO). This British Standard has accordingly been based on ISO Recommendation R702 which provides dimensions and tolerances for two types of lathe spindle noses and faceplates (Types “A” and “Camlock”). It is intended that a f

15、urther part of this standard shall cover the dimensions of bayonet type spindle noses as soon as international agreement on this type has been achieved. Interchangeability. Although internal parts such as cams, screws and studs made to this specification will not interchange with similar parts made

16、to an inch specification, there is strict operational interchangeability for one same type (AorCamlock) between metric spindle noses and inch faceplates and vice versa. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsib

17、le for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to13 and a back cover. This standard has been updated (see copyright dat

18、e) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4442-1:1969 BSI 01-2000 1 1 Scope 1.1 This British Standard specifies dimensions for the following types of lathe spindle noses, their faceplates and component parts: Accessories fo

19、r Type Camlock: 1.2 The sizes are denoted by numbers which appear at the head of the tables. 1.3 The range of sizes for Type A spindle noses and faceplates is from No.3 to No.28. 1.4 The range of sizes for Camlock spindle noses, cams, studs, faceplates and accessories is from No.3 to No.20. 2 Dimens

20、ions and tolerances Dimensions and tolerances for spindle noses, faceplates, details and accessories shall be as given in Table 1 toTable 7. The dimensions are in millimetres. Spindle noses, Type A 1(two bolt circles) Table 1 Spindle noses, Type B 2(outer bolt circle only) Faceplates, Type A Table 2

21、 Spindle noses, Type Camlock Table 3 Cams, Type Camlock Table 4 Studs, Type Camlock Table 5 Faceplates, Type Camlock Table 6 Hexagon socket head screws for studs Table 7a. Hexagon socket head screws for cams Table 7b. Stop bolt for cams Table 7c. Cheese head screw for cams Table 7d. BS4442-1:1969 2

22、BSI 01-2000 The B size is taken at the theoretical point of intersection between the generating line of the cone and the face of the flange. * F 1for type A 1with inner bolt circle F 2for type A 2without inner bolt circle. Figure 1 Spindle noses, Types A 1and A 2(seeTable 1)BS4442-1:1969 BSI 01-2000

23、 3 Table 1 Spindle noses, Types A 1and A 2 Type A 1 : Two bolt circles with radius C and D Type A 2 : Only the outer bolt circle with radius C (Type A 2for Nos.3 and4; Types A 1and A 2for Nos.5 to28) Sizes in millimetres No. 3 4 5 6 8 11 15 20 28 Tolerances A 92 108 133 165 210 280 380 520 725 B 53.

24、975 63.513 82.563 106.375 139.719 196.869 285.775 412.775 584.225 a C 35.3 41.3 52.4 66.7 85.7 117.5 165.1 231.8 323.8 b D 30.95 41.3 55.55 82.55 123.8 184.15 265.1 b E 16 20 22 25 28 35 42 48 56 F 1 d 14.288 15.875 17.462 19.05 20.638 22.225 25.4 c F 2 d 11 11 13 14 16 18 19 21 24 H 14.25 15.9 19.0

25、5 23.8 28.6 34.9 41.3 50.8 H8/h8 a I 5 5 5 6 8 8 8 8 J M 10 M 10 M 10 M 12 M 16 M 18 M 22 M 24 M 30 K 14 17 19 22 25 32 37 42 50 NOTEGeneral tolerance for untoleranced dimensions: 0.4mm. a SeeBS 1916, “Limits and fits for engineering,” Part1, “Limits and tolerances”. b 0.1mm for No.3 to11 0.15mm for

26、 No.15 to28 buttons and fixing holes Tolerance of position (radial and angular deviation with respect to the theoretical position). c 0.025mm for No.5 to28 d F 1for Type A 1 , F 2for Type A 2 . +0.008 0 +0.008 0 +0.01 0 +0.01 0 +0.012 0 +0.014 0 +0.016 0 +0.020 0 +0.023 0 +1T4 0 BS4442-1:1969 4 BSI

27、01-2000 Table 2 Faceplates, Type A Figure 2a Machining with inner bolt circle (for mounting on spindle nose A 1by means of its inner bolt circle). Figure 2b Machining with outer bolt circle (for mounting on spindle nose A 1 , or spindle nose A 2by means of its outer bolt circle). Figure 2c Machining

28、 with two bolt circles (for mounting either on spindle nose A 2 , or on spindle nose A 1by means of inner or outer bolt circle). Figure 2 Faceplates, Type A (seeTable 2) For alternative methods of machining seeFigure 2a,Figure 2b, andFigure 2c. Sizes in millimetres No. 3 4 5 6 8 11 15 20 28 Toleranc

29、es A 92 108 133 165 210 280 380 520 725 B 53.975 63.513 82.563 106.375 139.719 196.869 285.775 412.775 584.225 a C 35.3 41.3 52.4 66.7 85.7 117.5 165.1 231.8 323.8 b D 30.95 41.3 55.55 82.55 123.8 184.15 265.1 b F 1 c 14.288 15.875 17.462 19.05 20.638 22.225 25.4 +0.025 F 2 c 15 16 18 20 21 23 26 mi

30、n. G 10 10 12 13 14 16 17 19 22 H 14.7 16.3 19.45 24.2 29.4 35.7 42.1 51.6 +0.1 I 6.5 6.5 6.5 8 10 10 10 10 J 12 12 12 14 18 20 24 26 33 NOTEGeneral tolerance for untoleranced dimensions: 0.4mm. a SeeBS1916, “Limits and fits for engineering”, Part1, “Limits and tolerances”. b 0.1mm for No.3 to11 0.1

31、5mm for No.15 to28 buttons and fixing holes Tolerance of position (radial and angular deviation withrespecttothetheoreticalposition) c F 1for Type A 1 ; F 2for Type A 2(and eventually for Type A 1also, if the faceplate is rigid enough not to risk bending when the screws are clamping on the inner bol

32、t circle). +0.003 0.005 +0.003 0.005 +0.004 0.006 +0.004 0.006 +0.004 0.008 +0.004 0.010 +0.004 0.012 +0.005 0.015 +0.006 0.017 +(1T41T3) 1T3 BS4442-1:1969 BSI 01-2000 5 The B size is taken at the theoretical point of intersection between the generating line of the cone and the face of the flange. F

33、igure 3 Spindle noses, Type Camlock (seeTable 3)BS4442-1:1969 6 BSI 01-2000 Table 3 Spindle noses, Type Camlock Sizes in millimetres No. 3 4 5 6 8 11 15 20 Tolerances A 92 117 146 181 225 298 403 546 B 53.975 63.513 82.563 106.375 139.719 196.869 285.775 412.775 a C 35.3 41.3 52.4 66.7 85.7 117.5 16

34、5.1 231.8 b D 15.1 16.7 19.8 23 26.2 31 35.7 42.1 E 32 34 38 45 50 60 70 82 min. F 11 11 13 14 16 18 19 21 K 11.1 11.1 13.5 15.9 18.25 21.45 24.6 28.6 0.1 R 22.6 27 32 41 57 86 129 190 c J 17.5 17.5 20.6 23.8 27 31.8 36.5 42.9 a 18 18.6 15 36 14 55 13 46 12 18 10 30 8 35 7 5 b g 19 19 22 26 29 32 35

35、 42 H8 a h 27.5 36 46 57 64 75 84 94 d 1 15.5 15.5 10.5 13.5 13.5 13.5 16.5 16.5 1 7 9 9 9 11 11 1 1 30 40 0.2 P M 8 M 8 M 6 M 8 M 8 M 8 M 10 M 10 NOTEGeneral tolerance for untoleranced dimensions: 0.4mm. a SeeBS1916, “Limits and fits for engineering”, Part1, “Limits and tolerances”. b 0.05mm for No

36、.3 0.075mm for Nos.4 to20 Tolerance of position (radial and angular deviation with respect to the theoretical position) c 0.05 mm for No.3 and4 0.1mm for No.5 to20 +0.008 0 +0.008 0 +0.01 0 +0.01 0 +0.012 0 +0.014 0 +0.016 0 +0.020 0 +0.023 0 +005 0 +0.2 0 BS4442-1:1969 BSI 01-2000 7 Figure 4 Cams,

37、Type Camlock (seeTable 4)BS4442-1:1969 8 BSI 01-2000 Table 4 Cams, Type Camlock Sizes in millimetres No. 3 4 5 6 8 11 15 20 Tolerances A 13 17 22 25 28 32 37 43 min. B 13.4 11.9 14.2 16.7 18.9 21.2 23.5 27.8 0.2 C 7.5 9.5 11.1 12.7 14.2 16.7 19 22.2 D 1.65 1.6 1.45 2.56 2.46 2.44 2.35 3.1 +0.3 E 0.1

38、5 0.15 0 0.45 0.36 0.28 0.2 0.5 +0.1 F 15 10 10 10 10 15 15 15 G 15 15 15 20 20 20 20 20 H 26.5 35 45 56 63 73 82 92 0.1 I 2.2 2.2 3 4.2 5.3 8.7 6 6 0.1 J 3.6 3.6 5 6.5 6.5 6.5 8.5 8.5 a K 19 19 22 26 29 32 35 42 e8 b L 13 13 14 17 21 24 27 33 c M 4.5 6 6 6 8 8 0.05 N 2 2.85 3.95 7.35 5.2 5.2 0.1 O

39、14.9 16.7 22.4 30.2 33.2 39.5 43.6 48.4 0.2 P 21.4 26.5 35 43 49 59 62 69 Q 8 10 11 12 14 17 17 22 D12 b R 7 10 10 10 10 10 S 13 15 15 15 15 15 T 8 9 11 12 14 16 16 20 U 1.2 1.2 Slope on V d 1.6 1.9 1.9 2.64 2.64 2.64 2.64 3.18 NOTEGeneral tolerance for untoleranced dimensions: 0.4mm. a 0.05mm for N

40、o.3 and4; 0.1 for No.5 to20. b SeeBS1916, “Limits and fits for engineering”, Part1, “Limits and tolerances”. c 0.2mm for No.3 and4 only. d Tolerance: seetolerance on sizes of checking D and E.BS4442-1:1969 BSI 01-2000 9 Table 5 Studs, Type Camlock Figure 5 Studs, Type Camlock (seeTable 5) Sizes in m

41、illimetres No. 3 4 5 6 8 11 15 20 Tolerances A 12.7 13.5 16.5 19.6 23.2 26.8 32 38.5 0.1 B 4.2 4.8 4.8 4.8 4.8 6.4 6.4 6.4 0.2 C 14.3 15.9 19 22.2 25.4 30.2 34.9 41.3 0.1 D M10 1 M10 1 M12 1 M16 1.5 M20 1.5 M22 1.5 M24 1.5 M27 2 E 8.7 9.5 11.9 14.3 16.7 20.6 24.6 28.6 0.1 G 35 37 43 49 55.5 67 76 89

42、 H 19 19 22 27 30.5 35 40 44 I 30 31 35.7 40.5 44.5 53.2 58.7 69 0.2 J 9.5 9.5 11.25 12.7 14.3 15.9 17.5 20.6 K 11 11 11 14 14 14 14 14 NOTEGeneral tolerance for untoleranced dimensions: 0.4mm.BS4442-1:1969 10 BSI 01-2000 Figure 6 Faceplates, Type CamlockBS4442-1:1969 BSI 01-2000 11 Table 6 Faceplat

43、es, Type Camlock Sizes in millimetres No. 3 4 5 6 8 11 15 20 Tolerances A 92 117 146 181 225 298 403 546 B 53.975 63.513 82.563 106.375 139.719 196.869 285.775 412.775 a C 35.3 41.3 52.4 66.7 85.7 117.5 165.1 231.8 b D M101 1 M101 1 M121 1 M161 1.5 M201 1.5 M221 1.5 M241 1.5 M271 2 F 13 13 15 16 18

44、20 21 23 min. G 10 10 12 13 14 16 17 19 H 26 28 30 35 38 45 50 55 I 14.6 16.2 19.4 22.6 25.8 30.6 35.4 41.6 J 7 8 8 9.5 9.5 13 13 13 K 10.5 10.5 10.5 13.5 13.5 13.5 13.5 13.5 L a 11.0 11.0 12.5 15.5 17.5 18.7 21.5 24.8 M 7 7 7 9 9 9 9 9 p c M6 M6 M6 M8 M8 M8 M8 M8 c 18 18.6 15 36 14 55 13 46 12 18 1

45、0 30 8 35 7 05 NOTEGeneral tolerance for untoleranced dimensions: 0.4mm. a SeeBS1916, “Limits and fits for engineering”, Part1, “Limits and tolerances”. b 0.05mm for No.3 0.075mm for No.4 0.1mm for Nos.5 to20 Tolerance of position (radial and angular deviation with respect to the theoretical positio

46、n) c Tolerance of position of the axis of the hole p (radial and angular deviation with respect to the theoretical position defined by andL):0.1mm. +0.003 0.005 +0.003 0.005 +0.004 0.006 +0.004 0.006 +0.004 0.008 +0.004 0.010 +0.004 0.012 +0.005 0.015 +(1T41T3) 1T3 BS4442-1:1969 12 BSI 01-2000 Table

47、 7 Type Camlock accessories 7a. Hexagon socket head screws for studs Sizes in millimetres No. 3 4 5 6 8 11 15 20 a 10 10 10 13 13 13 13 13 d (M 6) (M 6) (M 6) (M 8) (M 8) (M 8) (M 8) (M 8) k 6 6 6 8 8 8 8 8 Figure 7a l 12 12 12 14 14 14 14 14 7b. Hexagon socket head screws for cams Sizes in millimet

48、res No. 3 4 5 6 8 11 15 20 a 10 13 13 13 16 16 d (M 6) (M 8) (M 8) (M 8) (M 10) (M 10) d 1 a 4.5 6 6 6 8 8 k 6 8 8 8 10 10 l 19 20 23 28 30 35 Figure 7b m 4 5 5 5 5 5 a The values indicated for d 1are maximum: the values to be used are those of dog-point screws.BS4442-1:1969 BSI 01-2000 13 Table 7 Type Camlock Accessories 7c. Stop bolt for cams Sizes in millimetres No. 3 and 4 5 6 8 11 15 20 b a 3.5 c 0.8 d 6.3 l b 14.4 m 4.8 a Tolerance:0.05 b Tolerance:0.2 Figure 7c 7