BS 4475-2000 Specification for straight mineral lubricating oils《纯矿物润滑油规范》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 4475:2000 Incorporatin

2、g Corrigendum No. 1 ICS 75.100 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Specification for Straight mineral lubricating oilsThis British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the author

3、ity of the Standards Committee and comes into effect on 15 November 2000 BSI 01-2001 First published June 1969 Second edition October 1975 Third edition December 1991 Fourth edition November 2000 The following BSI references relate to the work on this standard: Committee reference PTI/7 Draft for co

4、mment 98/122602 DC ISBN 0 580 33213 6 BS 4475:2000 Amendments issued since publication Amd. No. Date Comments 12089 January 2001 Correction to title of Table 2. Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PTI/7, Lubri

5、cants and process fluids, upon which the following bodies were represented: Agricultural Engineers Association Ball and Roller Bearing Manufacturers Association British Fluid Power Association British Gear Association British Lubricants Federation Ltd. Institute of Petroleum Ministry of Defence Soci

6、ety of Motor Manufacturers and TradersBS 4475:2000 BSI 01-2001 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Normative references 1 3 Sampling 1 4 Composition 1 5 Requirements 2 6 Packaging and marking 2 Bibliography 5 Table 1 Straight mineral lubricating oils for

7、 total loss systems (Type ISO-L-AN) 3 Table 2 Straight mineral lubricating oils for circulating systems (Type CS) 4ii BSI 01-2001 BS 4475:2000 Foreword This British Standard has been prepared by Technical Committee PTI/7, Lubricants and process fluids, and supersedes BS 4475:1991, which is withdrawn

8、. This standard is intended to assist users concerned with the selection of lubricants for industrial equipment, machine designers, lubricant suppliers, and those responsible for the use and maintenance of equipment. The requirements specified are those essential for a lubricant, namely viscosity in

9、 terms of the classification in BS 4231, viscosity/temperature characteristics, flashpoint, pour point and freedom from acidic constituents. An additional requirement is given for demulsibility, i.e. the ability of an oil to permit separation of water, which is important in certain applications wher

10、e water is liable to occur in service. This British Standard specifies requirements for two types of straight mineral lubricating oils, each containing 13 viscosity grades. One type of oil is intended primarily for use in total loss systems, i.e. those in which the oil is run to waste after performi

11、ng its function. The other type of oil is intended for use in circulating systems in which the oils are retained or recirculated. A number of preferred viscosity grades are indicated in an attempt to rationalize oil stocks. It is hoped that equipment manufacturers will select these preferred viscosi

12、ty grades when designing new equipment and will recommend their use, thus providing a progressive reduction in the number of grades required. This British Standard does not cover lubricating oils containing additives which enhance the properties of the lubricant. Pour point depressants are, however,

13、 permitted to ensure compliance of the oil with this standard. This edition introduces the current editorial format and updates the methods of test, but does not reflect a full review or revision of BS 4475:1991, which will be undertaken in due course. A British Standard does not purport to include

14、all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i a

15、nd ii, pages 1 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.BS 4475:2000 BSI 01-2001 1 1 Scope This British Standard specifies requirements for two types of straight mineral lubricating oil, with one type suitable for use in t

16、otal loss systems and the other in circulating systems. 2 Normative references The following normative documents contain provisions which, through reference in the text, constitute provisions of this British Standard. For dated references subsequent amendments to, or revisions of, any of these publi

17、cations do not apply. For undated references, the latest edition of the publication referred to applies. BS 2000-15, Methods of test for petroleum and its products Part 15: Petroleum products Determination of pour point. BS 2000-139, Methods of test for petroleum and its products Part 139: Petroleum

18、 products and lubricants Determination of acid or base number Colour-indicator titration method. BS 2000-182, Methods of test for petroleum and its products Part 182: Determination of inorganic acidity of petroleum products Colour indicator titration method. BS 2000-226, Methods of test for petroleu

19、m and its products Part 226: Petroleum products Calculation of viscosity index from kinematic viscosity. BS 2000-412, Methods of test for petroleum and its products Part 412: Petroleum products Determination of water separability of petroleum oils and synthetic fluids. BS 4231, Classification for vi

20、scosity grades of industrial liquid lubricants. BS 6413-1, Lubricants, industrial oils and related products (class L) Part 1: Classification for family A (total loss systems). BS EN ISO 3104:1996, Methods of test for petroleum and its products Petroleum products Transparent and opaque liquids Determ

21、ination of kinematic viscosity and calculation of dynamic viscosity. (BS 2000-71:1) BS EN 22719, Methods of test for petroleum and its products Petroleum products and lubricants Determination of flash point Pensky-Martens closed cup method. (BS 2000-404:1994) BS EN ISO 3170, Petroleum liquids Manual

22、 sampling. BS EN ISO 4259, Petroleum products Determination and application of precision data in relation to methods of test. (BS 2000-367:1996) NOTE Copies of the BS 2000 series of standards are available from the Institute of Petroleum, 61 New Cavendish Street, London W1M 8AR. 3 Sampling For the p

23、urposes of this British Standard, all sampling shall be carried out in accordance with the relevant procedures and precautions described in BS EN ISO 3170. 4 Composition The oils shall be pure mineral oils free from additives, except that when the pure mineral oils cannot comply with the pour point

24、requirement (see Table 1), it is permissible to add a pour point depressant. On visual inspection, the oils shall be clear and free from water, suspended matter, dirt and sediment. NOTE Oils of the same quality level i.e. bearing the same designation (ISO-L-AN or CS conforming to this standard are c

25、ompatible with one another and may be mixed in any proportion.2 BSI 01-2001 BS 4475:2000 1) Marking BS 4475:2000 on or in relation to a product represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that the product meets the requirements of the standa

26、rd. The accuracy of the claim is solely the claimants responsibility. Such a declaration is not to be confused with third-party certification of conformity. 5 Requirements 5.1 General When tested in accordance with the methods shown in Tables 1 or 2 as appropriate, the oils shall conform to the limi

27、ting requirements given in the relevant table for the grade concerned. 5.2 Grade designations 5.2.1 General Oils supplied to this standard shall be designated type (ISO-L-AN or CS) and viscosity grade number. 5.2.2 Type designation Oils for total loss systems (see Table 1) shall be designated accord

28、ing to the classification in BS 6413-1 for defined mineral oils, i.e. ISO-L-AN. Oils for circulating systems (see Table 2) shall be designated CS. 5.2.3 Viscosity grade All types of oil shall additionally be designated according to their viscosity in accordance with the ISO viscosity classification

29、given in BS 4231, i.e. a number corresponding to the mid-point kinematic viscosity at 408C, e.g. ISO VG 150. NOTE The viscosity designation may be abbreviated in the full designation, e.g. CS 150. 5.3 Demulsibility If required, the demulsification number for a circulating system oil shall be determi

30、ned in accordance with BS 2000-412. If an oil conforming to the additional requirement for demulsibility is specified, the grade designation shall be identified by the addition of the letter X following the viscosity number. For viscosity grades up to and including CS 100, the limit shall be 40/40/0

31、 in 5 min. For viscosity grades CS 150 to CS 1 000, the limit shall be 40/40/0 in 20 min. 5.4 Precision and interpretation of results Most of the methods given in Tables 1 and 2 contain a statement of the precision, i.e. the repeatability and reproducibility to be expected from them but, in cases of

32、 dispute, the procedure described in BS EN ISO 4259, which uses precision data in the interpretation of the results, shall be used. 6 Packaging and marking The oils shall be supplied in bulk or in clean, sound and dry containers as agreed between the purchaser and supplier. Each container shall be l

33、egibly and durably marked with the following: a) the number and date of this British Standard, i.e. BS 4475:2000 1) ; b) the type and grade designation, e.g. ISO-L-AN 150, CS 68; c) the name or mark of the supplier or vendor and the batch or consignment number. BSI 01-2001 3 BS 4475:2000 Table 1 Str

34、aight mineral lubricating oils for total loss systems (Type ISO-L-AN) Viscosity grade no. (see BS 4231) 10 15* 22 32* 46 68* 100 150* 220 320* 460 680* 1 000* Test method BS reference Technically identical with Viscosity kinematic (at 40.08C, cSt) a min. 9.0 13.5 19.8 28.8 41.4 61.2 90 135 198 288 4

35、14 612 900 BS EN ISO 3104 IP 71: Section 1 max. 11.0 16.5 24.2 35.2 50.6 74.8 110 165 242 352 506 748 1 100 Flashpoint Pensky-Martens closed (C) min. 120 132 150 165 171 183 192 192 204 216 228 237 237 BS EN 22719 b IP 404 Pour point (C) max 29 29 29 29 29 26 26 23 23 23 23 23 6 BS 2000-15 IP 15 Tot

36、al acidity (mg KOH/g) max. 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.5 0.5 0.5 0.5 BS 2000-139 IP 139 Inorganic acidity (mg KOH/g) max. Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 Below 0.01 BS 2000-182 IP 182 NOTE T

37、he grades indicated by an asterisk are preferred grades (see Foreword, paragraph 7). a 1c S t=1mm 2 /s = 13 10 26 m 2 /s. b Any determination above 2508C, the precision statement given in BS EN 202719 does not apply.BS 4475:2000 4 BSI 01-2001 Table 2 Straight mineral lubricating oils for circulating

38、 systems (Type CS) Viscosity grade no. (see BS 4231) 10 15* 22 32* 46 68* 100 150* 220 320* 460 680* 1 000* Test method BS reference Technically identical with Viscosity kinematic (at 40.08C, cSt) a min. 9.0 13.5 19.8 28.8 41.4 61.2 90 135 198 288 414 612 900 BS EN ISO 3104 IP 71: Section 1 max. 11.

39、0 16.5 24.2 35.2 50.6 74.8 110 165 242 352 506 748 1 100 Viscosity index min. 80 80 90 90 90 90 90 90 90 90 90 80 70 BS 2000-226 IP 226 Flashpoint Pensky-Martens closed (8C) min. 132 150 165 171 183 192 204 216 228 237 237 249 261 BS EN 22719 b IP 404 Pour point (8C) max. 218 218 29 29 29 29 29 29 2

40、6 26 26 23 6 BS 2000-15 IP 15 Total acidity, (mg KOH/g) max. 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 BS 2000-139 IP 139 NOTE The grades indicated by an asterisk are preferred grades (see Foreword, paragraph 7). a 1c S t=1mm 2 /s = 13 10 26 m 2 /s. b Any determination above 2508C, the pre

41、cision statement given in BS EN 22719 does not apply. BSI 01-2001 5 BS 4475:2000 Bibliography BS 2000-19, Methods of test for petroleum and its products Part 19: Determination of demulsifibility characteristics of lubricating oil. BS 2000-306, Methods of test for petroleum and its products Part 306:

42、 Determination of oxidation stability of straight mineral oil. NOTE Copies of the BS 2000 series of standards are available from the Institute of Petroleum, 61 New Cavendish Street, London W1M 8AR.BS 4475:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | |

43、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparin

44、g British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.

45、It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside f

46、ront cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be add

47、ressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide r

48、ange of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 711

49、1. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract