BS 4550-3 1-1978 Methods of testing cement - Physical tests - Introduction《水泥试验方法 第3 1部分 物理试验 总则》.pdf

1、BRITISH STANDARD BS 4550-3.1: 1978 Methods of testing cement Part 3: Physical tests Section 3.1 Introduction IMPORTANT NOTE. It is recommended that this Section be read in conjunction with the information in the “General introduction” to BS4550, which is issued separately. UDC 666.94.01:620.1:53BS45

2、50-3.1:1978 This British Standard, having been prepared under the direction of the Cement, Gypsum, Aggregates and Quarry Products Standards Committee, was published under the authority of the Executive Board on 30 June 1978 BSI 03-1999 The following BSI references relate to the work on this standard

3、: Committee reference CAB/1 Draft for comment 73/10751 DC ISBN 0 580 10136 3 Foreword This British Standard has been prepared under the direction of the Cement, Gypsum, Aggregates and Quarry Products Standards Committee. It brings together and revises the physical test methods described in appendice

4、s to the following British Standards: BS 12-2:1971, Portland cement (ordinary and rapid-hardening). BS 146-2:1973, Portland-blastfurnace cement. BS 915-2:1972, High alumina cement. BS 1370-2:1974, Low heat Portland cement. BS 4027-2:1972, Sulphate-resisting Portland cement. BS 4246-2:1974, Low heat

5、Portland-blastfurnace cement. BS 4248:1974, Supersulphated cement. BS 5224:1976, Specification for masonry cement. Part 0 of BS4550 is a general introduction; Part1 lays down methods of sampling cement; Part2 describes methods of chemical testing of cement; Part4 specifies the standard coarse aggreg

6、ate for concrete cubes; Part5 specifies the standard sand for concrete cubes and Part 6 specifies the standard sand for mortar cubes. Publication of BS4550 enables the standards listed in the previous paragraph to be revised by deletion of the relevant appendices. This will avoid repetition in the e

7、xpanding range of cement standards and ensure that, if changes are made in any of the test methods, the standards remain in step. It is anticipated that the mortar cube test will be deleted on the first revision of this Part of this standard. The ISO mortar prism test has not been included as a stan

8、dard method of test, since the method is at an advanced stage of revision under the direction of CEN and publication is expected in the near future. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct

9、 application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyrig

10、ht date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS4550-3.1:1978 BSI 03-1999 i Contents Page Foreword Inside front cover 1 Scope 1 2 References 1 3 Definitions

11、 1 4 Sampling 1 Publications referred to Inside back coverii blankBS4550-3.1:1978 BSI 03-1999 1 1 Scope This Part of this British Standard specifies methods for the physical testing of cement. The methods of test are issued separately as follows: 3.2 Density test 3.3 Fineness test 3.4 Strength tests

12、 3.5 Determination of standard consistence 3.6 Test for setting times 3.7 Soundness test 3.8 Test for heat of hydration 2 References The titles of the publications referred to in this Section are given on the inside back cover. 3 Definitions For the purposes of this Part of this BritishStandard, the

13、 definitions given in BS4627 apply. 4 Sampling Test samples for use in the following tests shall be obtained in accordance with BS 4550-1. The test sample shall be mixed thoroughly and a sample of the specified size for the required test shall be taken from it.2 blankBS 4550-3.1:1978 BSI 03-1999 Pub

14、lications referred to BS 4550, Methods of testing cement. BS 4550-1, Sampling. BS 4627, Glossary of terms relating to types of cements, their properties and components. BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

15、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK v

16、iew on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve

17、the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020

18、8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 899

19、6 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European

20、 and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing member

21、s of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI

22、also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying,

23、recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.