BS 5041-5-1974 Fire hydrant systems equipment - Specification for boxes for foam inlets and dry riser inlets《消防栓系统设备 第5部分 泡沫入口及干式水嘴用箱规范》.pdf

1、BRITISH STANDARD BS5041-5: 1974 Incorporating Amendment No. 1 Fire hydrant systems equipment Part 5: Specification for Boxes for foam inlets and dry riser inlets UDC 69.027.84:621.643.41:614.844BS5041-5:1974 This British Standard, having beenapproved by the Fire Standards Committee and endorsed by t

2、he Chairman of theBuilding Divisional Council, was published under the authorityofthe Executive Boardon 26February 1974 BSI04-1999 First published as BS3980, March1966 First published as BS5041-5, February1974 The following BSI references relate to the work on this standard: Committee references FSM

3、/6, FSB/6/4 Draft for approval72/11307 ISBN 0 580 07561 3 Co-operating organizations The Fire Standards Committee, under whose supervision this BritishStandard was prepared, consists of representatives from the following Government departments and industrial organizations: Association of Municipal F

4、ire Offices Committee* Corporations* Fire Protection Association British Constructional Steelwork Greater London Council Association Greater London Council Chief Fire Officers Association* (LondonFireBrigade)* Concrete Society Home Office* Confederation of British Industry Industrial Fire Protection

5、 County Councils Association Association of Great Britain Department of Employment Institution of Civil Engineers (HMFactoryInspectorate) Institution of Fire Engineers* Department of the Environment* Institution of Municipal Engineers* Department of the Environment Ministry of Defence, Procurement (

6、Joint Fire Research Executive Organization and Fire Offices National Council of Building Committee)* Material Producers Department of Trade and Industry Royal Institute of British Architects (Marine Division)* Fire Extinguishing Trades Association The Government departments and scientific and indust

7、rial organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Aluminium Federation Ministry of Defence, Air Force British Ironfounders Association Department British Fire

8、Services Association Ministry of Defence, Army British Valve Manufacturers Department Association National Coal Board Copper Development Association National physical Laboratory Fire Hose Manufacturers (Ministry of Technology) Association Individual manufacturers Amendments issued since publication

9、Amd. No. Date of issue Comments 5505 March 1987 Indicated by a sideline in the marginBS5041-5:1974 BSI 04-1999 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 Manufacture 1 4 Materials and thickness 1 5 Dimensions 2 6 Manufacturers certificate 3

10、7 Marking 3 Figure 1 Typical drawing of box for two foam inlets 3 Figure 2 Typical drawing of box for dry risers (four inlets) 4 Table 1 Foam inlet boxes 2 Table 2 Boxes for dry risers 2 Publications referred to Inside back coverBS5041-5:1974 ii BSI 04-1999 Foreword This part of BS5041 was originall

11、y published as BS3980. However, while the metricated version of BS3980 was being prepared, it was decided that it would be logical to issue the revised edition as Part5 of BS5041 “Fire hydrant systems equipment”. Parts1 to4 of BS5041, the titles of which are given below, are at present in course of

12、preparation. Part 1: Landing valves for wet risers; Part 2: Landing valves for dry risers; Part 3: Inlet breechings for dry risers; Part 4: Boxes for landing valves for dry risers. This standard was originally proposed by the London Fire Brigade and has been prepared under the authority of the Fire

13、Standards Committee to provide detailed specifications for most of the special requirements for wet and dry risers and foam inlets described in BS5306-1. This part of BS5041 supersedes BS3980:1966 and is intended to fulfill the same purpose as that standard, that is, to define the standard sizes and

14、 details of boxes for foam inlets and dry riser inlets so as to enable architects and builders to specify a standard product in metric terms. The metric values are given in SIunits; for further information on these, reference should be made to BS3763 “The International System of units (SI)”. The wor

15、k sizes have been selected to conform to the first or second preferences in BS4011 “Recommendations for the co-ordination of dimensions in building. Basic sizes for building components and assemblies” and this has led to a slight reduction in the maximum permissible size of the box compared with tha

16、t specified in BS3980. The boxes can also be used for other purposes, e.g.for fuel oil inlets and inlets for drencher systems. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Complian

17、ce with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had a

18、mendments incorporated. This will be indicated in the amendment table on theinside front cover.BS5041-5:1974 BSI 04-1999 1 1 Scope This British Standard specifies the requirements for boxes for foam inlets or dry risers manufactured in a choice of materials to suit a particular application. NOTEThe

19、titles of the British Standards referred to in this Standard are listed on the inside back cover. 2 Definitions For the purposes of this British Standard the following definitions apply: 2.1 Box a box containing the inlets of foam pipes or water mains, installed in, or within the boundaries of the s

20、ite of a building, preferably recessed in a wall with inlets normally at street level through which foam or water can be pumped to provide a supply at discharge points situated at various levels in the building 2.2 Dry riser a vertical pipe installed in a building for fire fighting purposes, fitted

21、with inlet connections at the base and with landing valves at specified points, which is normally dry but which is capable of being charged with water by pumping from fire service appliances 3 Manufacture 3.1 Box. The box shall be of robust construction with seamed edges to guard against the ingress

22、 of water. The bottom of the box shall be provided with a fall of not less than1 in12 and be suitably drained. The box shall be supplied with flanges not less than38mm wide on the external face (seeFigure 1 and Figure 2). The back of the box shall be provided with suitable holes to accommodate foam

23、inlets (of diameter65 mm or80mm) or dry risers (of diameter100 mm or150mm) (see BS4504). When there is more than one foam inlet in one box they shall be spaced at not less than175 mm centres. The box shall be supplied with suitable fixing lugs or screw holes in the back of the box to enable it to be

24、 built into position. 3.2 Door. The frame of the door shall be of rigid construction and designed to accommodate a spring lock. The door shall be side hung and shall open through approximately180 . The box shall have a striking plate to engage the lock when the door is closed. The spring lock shall

25、be such that it can also be operated and opened from the inside without the aid of a key when the glass has been broken. The front of the door shall be glazed. The glazed portions of the door shall be large enough to enable delivery hose(s) or foam branch pipe(s) to be connected to the inlet(s) even

26、 if the door cannot be opened and the only means of access is by breaking the glass. 3.3 Hinges. The hinges shall be of the butt type and be so fixed that, in the event of damage, they can be removed and replaced with the box remaining in situ. 3.4 Glass fixing. The door shall be provided with remov

27、able rebated frame for housing the glass. The rebated frame shall be attached to the door with brass screws and nuts. 3.5 Lock. The lock shall be a spring cylinder lock (with key) capable of being released from the inside without the use of the key. The lock shall not be fitted with a safety catch.

28、The lock shall be secured to the door frame by suitable means so that in the case of damage it can be removed and replaced. 3.6 Opening device. The external face of the door shall be provided with a countersunk finger hole to facilitate opening the door. 3.7 Designation 3.7.1 On glass front. The ins

29、ide surface of the glass panel of the box shall be marked with the words “Dry riser inlet(s)” or “Foam inlet(s)” as appropriate. The sign shall comply with the requirements for fire equipment signs in BS5499-1. The sign shall be rectangular, the wording shall be in white and the background red. The

30、letters shall be in lower case except for the initial letter “D” or “F”, which shall be in upper case. The letter height shall be either: 1) not less than50 mm; or 2) of such smaller size as may be necessary because of the size of the glass panel. 3.7.2 On indicator plates. An indicator plate or pla

31、tes (about100 mm 75 mm in size) shall be fixed within or on the outside of, or shall be provided for fixing adjacent to the inlet box to indicate the room or rooms with which the foam inlet(s) communicates. Where more than one inlet communicates with one compartment the position in the compartment s

32、hall be indicated. The sign(s) shall comply with the requirements for fire equipment signs, or for supplementary signs, in BS5499-1. They shall be rectangular, and the wording shall be in white and the background red or the wording shall be in black and the background white. The letters shall be in

33、lower case except for the initial letter, which shall be in upper case. 4 Materials and thickness 4.1 Box 4.1.1 The material used for the manufacture of the box shall be selected by agreement between the purchaser and the manufacturer from the following: 1) Rust proof steel (either galvanized, zinc

34、sprayed or metal coated) 2) Stainless steel to comply with the requirements of BS1449-4BS5041-5:1974 2 BSI 04-1999 3) Brass to comply with the requirements of the series BS2870 to BS2875 for wrought material and BS1400 for cast material 4) Aluminium alloy to comply with the requirements of BS1490 or

35、 with the requirements of the series BS1470 to BS1475 4.1.2 Whatever the choice of materials for the box the thickness of it shall be not less than1.5 mm and not more than3.5 mm. 4.2 Hinges and pins 4.2.1 Hinges including pins shall be manufactured in suitable rustless material. 4.2.2 If aluminium a

36、lloy is to be used in a hinge or pin the choice unless otherwise specified by the purchaser shall be made from wrought alloy to comply with the requirements of the series BS1470 to BS1475 and selected from the following types: Type N8 Type H9 Type H30. 4.3 Doors. Door frames shall be made of non-fer

37、rous or rust proofed material not less than3.5 mm thick. 4.4 Anti-corrosion 4.4.1 In all conditions the edges of any part made from material which is not itself rust-proof shall be suitably treated to resist corrosion. 4.4.2 When the purchaser requires the article for use in especially corrosive con

38、ditions, any aluminium alloy used in it shall be anodized. 4.5 Glazing. The glazing in the door shall be of wired glass6 mm thick. 5 Dimensions 5.1 Boxes. Boxes shall conform to the dimensions shown in Table 1 and Table 2. Table 1 Foam inlet boxes Table 2 Boxes for dry risers All sizes in millimetre

39、s No. of inlets for which box is required Length (acrossfaceofbox) Height (abovelowestpointofbox) Width (fromfronttobackofbox) Work size a Co-ord. size Work size a Co-ord. size Work size a Co-ord. size One inlet 295 300 295 300 195 200 Two inlets alternative1 595 600 295 300 195 200 alternative2 295

40、 300 595 600 195 200 Three inlets alternative1 795 800 295 300 195 200 alternative2 295 300 795 800 195 200 a Permissible deviations on work sizes are+ 3 and 0 for all sizes. All sizes in millimetres Diameter of riser for which box is required b Length (across face of box) Height (abovelowestpointof

41、 box) Width (fromfronttobackofbox) Work size a Co-ord. size Work size a Co-ord. size Work size a Co-ord. size 100 alternative1 595 600 395 400 295 300 alternative2 395 400 595 600 295 300 150 595 600 595 600 295 300 a Permissible deviations on work sizes are+ 3 and 0 for all sizes. b Dry riser inlet

42、s are designed to take collecting heads for either two hose connections in the case of100 mm mains, or four hose connections in the case of150 mm mains.BS5041-5:1974 BSI 04-1999 3 5.2 Size of glazed opening in door. The size of glazed opening for all doors shall be governed by the requirements a and

43、 b given in Figure 1. 5.3 Size of glass in door frame. The size of glass shall be such that it shall extend not more than15mmbeyond the opening in the door. 6 Manufacturers certificate If requested, the manufacturer shall forward a certificate of compliance with the requirements of this British Stan

44、dard to the purchaser or his representative. 7 Marking Every box conforming to the requirements of this specification shall be marked with the number of the British Standard, i.e.BS5041-5 1) , as a claim by the manufacturer that the article complies with the requirements of the Standard. 1) Marking

45、BS5041-5 on or in relation to a product is a claim by the manufacturer that the product has been manufactured to the requirements of the standard. The accuracy of such a claim is therefore solely the manufacturers responsibility. Enquiries as to the availability of third party certification should b

46、e addressed to the appropriate certification body. Figure 1 Typical drawing of box for2 foam inlets NOTEThis amended figure shows the amended letter style for “Foam inlet” and corrects the proportions of the drawings; the actual dimensions of the box are unchanged.BS5041-5:1974 4 BSI 04-1999 Figure

47、2 Typical drawing of box for dry risers (4 inlets) NOTEThis amended figure corrects the apparent proportions of the drawings only; the actual dimensions of the box are unchanged.BS5041-5:1974 BSI 04-1999 Publications referred to This standard makes reference to the following British Standards: BS140

48、0, Copper alloy ingots and copper and copper alloy castings. BS1449, Steel plate, sheet and strip. BS1449-4, Stainless and heat resisting plate, sheet and strip. BS1470, Wrought aluminium and aluminium alloys for general engineering purposes Plate, sheet and strip. BS1471, Wrought aluminium and alum

49、inium alloys for general engineering purposes. Drawn tube. BS1472, Wrought aluminium and aluminium alloys for general engineering purposes. Forging stock and forgings. BS1473, Wrought aluminium and aluminium alloys for general engineering purposes. Rivet, bolt and screw stock. BS1474, Wrought aluminium and aluminium alloys for general engineering purposes. Bars, extruded round tube and sections. BS1475, Wrought aluminium and aluminium alloys for general engineering purposes. Wire. BS1490, Aluminium and aluminium ingots and castings. BS