1、BRITISH STANDARD BS 5131-4.7: 1975 Methods of test for Footwear and footwear materials Part 4: Other components Section 4.7 Resistance to peeling of ribs stuck to insoles NOTEIt is recommended that this Section should be read in conjunction with the information in the General introduction to BS 5131
2、, published separately. UDC 685.31:620.1:685.312.124:676.017.435.4BS5131-4.7:1975 BSI 10-1999 ISBN 0 580 08358 6 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Brit
3、ish Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This wil
4、l be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBS5131-4.7:1975 BSI 10-1999 i Contents Page 1 Scope 1 2 Reference 1 3 Principle 1 4 Supplementary information 1 5 Test pieces 1 6 Apparatus and material 1 7 Procedure 1 8 Expres
5、sion of results 3 9 Test report 3 Figure 1 Test piece layout for the determination both of the resistancetopeeling and the shear strength of an attached rib insole 2 Figure 2 Test piece layout for the determination both of the resistance topeeling and the shear strength of ribs stuck to insole mater
6、ial 2ii blankBS5131-4.7:1975 BSI 10-1999 1 1 Scope This Section describes a peel test for assessing the adhesion of a rib to the attached insole. Provision is also made for peel testing after water soaking to simulate the wetting effect of perspiration during wear. The test may be carried out either
7、 on ribbed insoles or on sample strips of insole material with ribs affixed along the edges. NOTESection4.7 is based on SATRA 1)Method AM 1, Appendix R. 2 Reference This Section refers to BS 3978 “Water for laboratory use”. 3 Principle The rib is peeled from the attached insole in a tensile-testing
8、machine. Separate determinations are carried out on dry and on wet test pieces. 4 Supplementary information In the case of strips of insole material, the procedure described in this Section requires to be completed by information on the means of attaching the ribs to the insole material. This inform
9、ation shall be derived from the British Standard, or other specification, for the material under test or shall be the subject of agreement between parties interested in the results of the test. 5 Test pieces NOTEPeel tests are usually combined with shear tests on the rib. Figure 1 and Figure 2 show
10、convenient combined layouts of test pieces for both tests. Section4.6 of BS5131 describes a procedure for the determination of shear strength. 5.1 Ribbed insoles 5.1.1 Test two insoles, taking four test pieces, each about750mm long, from each. Mark out test pieces for wet and for dry peel testing ac
11、cording to a suitable scheme, such as that indicated inFigure 1. 5.1.2 Cut out the eight peeling test pieces, marking on them suitable directions of peel, such as those shown inFigure 1. Because the adhesion at the two ends of the rib and at the toe may be unrepresentative of the adhesion as a whole
12、, do not peel towards these points. 5.1.3 Trim the width of each test piece until it is the overall width of the rib flange; if the fabric has a pinked edge do not cut any of this away. 5.1.4 Apply heat locally to soften the adhesive over a 1.5 cm to 2.5 cm length at the end of the test piece from w
13、hich peeling is to be started and separate the rib flange from the insole by hand. (This is usually best done by pressing a hot metal strip on to the rib fabric flange for a few seconds.) 5.2 Insole material (See also the note to clause8.) 5.2.1 Cut strips of material approximately 750mm wide and 35
14、0mm long. If the insole material has a direction marked for cutting out, cut one strip with its length in this direction. Otherwise, cut one strip in the machine direction and one strip in the cross direction. 5.2.2 Attach ribs to the longer edges of the strips, using the agreed method (see clause4)
15、. 5.2.3 Mark out eight peeling test pieces on each cut strip, using a suitable plan, such as that shown inFigure 2. 5.2.4 Proceed as described in 5.1.3 and 5.1.4. 6 Apparatus and material Use the following apparatus and material. a) Tensile-testing machine, low-inertia, continuous-recording, with a
16、jaw separation rateof 10 2 cm/min and a load range of 0 to100N (0 to 10 kgf). NOTEOne suitable apparatus is the SATRA cantilever tensiometer (STD 160161). b) Water, complying with the requirements of BS3978. 7 Procedure 7.1 Wet testing 7.1.1 Carry out the following procedure on each test piece taken
17、 for wet testing. 7.1.2 Immerse the test pieces in the water at20 2 C for 6 h. 7.1.3 Remove the test pieces from the water and clamp the separate ends of the rib and insole each in a jaw of the tensile-testing machine. Separate the jaws at 102cm/min while recording the force and extension continuous
18、ly. When peeling is completed, examine the peeled area and note the type of failure, ignoring the first centimetre peeled as the adhesive here may have been affected by the heat applied to start the separation. 1) Shoe and Allied Trades Research AssociationBS5131-4.7:1975 2 BSI 10-1999 Figure 1 Test
19、 piece layout for the determination both of the resistance to peeling and the shear strength of an attached rib insole Figure 2 Test piece layout for the determination both of the resistance to peeling and the shear strength of ribs stuck to insole materialBS5131-4.7:1975 BSI 10-1999 3 Measure the o
20、verall rib width. Inspect the test record, and determine visually the mean peeling force, excluding the first centimetre peeled. NOTETypes of joint failure can be classified as follows: a) failure of adhesion to the rib fabric; b) failure of adhesion to the insole material; c) failure within the rib
21、 fabric; d) failure within the insole material; e) cohesive failure of the adhesive; f) non-coalescence of the adhesive films. 7.2 Dry testing. On each test piece taken for dry testing, carry out the procedure described in7.1.3. 8 Expression of results 8.1 Calculate for the four test pieces in each
22、series (i.e. wet and dry respectively) the overall mean of the mean peeling forces. Express the result, in newtons, as the peeling force wet or dry, respectively. 8.2 Calculate the mean overall rib width for each series of four test pieces. 8.3 If an insole material has been tested in more than one
23、direction (see the note and also 5.2.1), express the results for each direction separately. NOTEWith some cellulose boards, there may be a difference of results corresponding to the two directions along the length of the roll (i.e. usually at right angles to the heel-toe direction of cut insoles). I
24、f this effect is apparent (either from the test results or the type of failure) then results for each of these two directions should be obtained and reported separately. 9 Test report Include the following items in the test report: a) the peeling forces, expressed in accordance with clause 8 (the eq
25、uivalent values in kgf may be added in brackets); b) the corresponding mean overall rib widths; c) the type(s) of failure occurring; d) nature and full identification of the sample(s); e) in cases where, for the purposes of the test, ribs were attached to insole material strips, the details of the m
26、ethod of attachment; f) reference to the method of test (i.e. Section4.7 of BS5131); g) date of testing.BS 5131-4.7: 1975 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view o
27、n standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the qua
28、lity of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI
29、 offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089
30、967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international st
31、andards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to dat
32、e with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the
33、UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without pr
34、ior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1