BS 5F 58-2002 Cotton thread for aerospace purposes《航天航空用棉线》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS 5F 58:2002 (Superseding BS 4F 58:1990) Cotton thread for aerospace purposes ICS 49.025.60 BS 5F 58:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of t

2、he Sector Policy and Strategy Committee on 17 October 2002 BSI 17 October 2002 First published BS F 58:1947 Second edition BS 2F 58:1960 Third edition BS 3F 58:1975 Fourth edition BS 4F 58:1990 Fifth edition BS 5F 58:2002 The following BSI references relate to the work on this standard: Draft for co

3、mment 00/707768 DC Committee reference ACE/22 ISBN 0 580 37034 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/22, Cords, ropes and threads for aerospace purposes, upon which the following bodies were represented: L

4、inen Sewing Threads Manufacturers Association Ministry of Defence UK Defence Standardization Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBS 5F 58:2002 BSI 17 October 2002 i Contents Page Committees responsible Inside front cover Foreword ii 1

5、S c o p e 1 2 Normative references 1 3G e n e r a l 1 4Y a r n 2 5 Construction and properties 2 6 Finish 2 7T y p e t e s t 2 8 Identification 2 Table 1 General requirements (given in BS F 100) 1 Table 2 Construction and properties 2BS 5F 58:2002 ii BSI 17 October 2002 Foreword This British Standar

6、d, prepared under the direction of Technical Committee ACE/22, is one of a series for textiles of a quality suitable for aerospace purposes. It supersedes BS 4F 58:1990 which is withdrawn. NOTE The previous edition, BS 4F 58:1990, differed from the earlier edition primarily in that only one thread w

7、as specified. This new edition updates references and improves nomenclature in line with other standards in the same series. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard

8、does not of itself confer immunity from legal obligations. WARNING NOTES This standard calls for the use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supplier or t

9、he user from statutory obligations relating to health and safety at any stage of manufacture or use. This standard specifies pentachlorophenyl laurate (PCPL) as the only approved rotproofing treatment for aerospace textiles. Alternative treatments are under development, and this standard will be upd

10、ated to delete PCPL as soon as an approved alternative treatment for aerospace textiles is available. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 2, an inside back cover and a back cover. The BSI copyright notice displayed in this documen

11、t indicates when the document was last issued.BS 5F 58:2002 BSI 17 October 2002 1 1 Scope This British Standard specifies the requirements for a cotton thread, for use primarily as safety ties and break threads, for aerospace purposes. NOTE The latest revision of an Aerospace Standard is indicated b

12、y the prefix number. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. BS 38

13、1C, Specification for colours for identification, coding and special purposes. BS 1932-2, Testing the strength of yarns and threads from packages Methods for determination of knot strength and loop strength. BS 2087-1, Preservative treatments for textiles Specification for treatments. BS F 100, Proc

14、edure for inspection and testing of textiles for aerospace purposes. BS EN ISO 2060:1995, Textiles Yarn from packages Determination of linear density (mass per unit length) by the skein method. BS EN ISO 2061, Textiles Determination of twist in yarns Direct counting method. 3 General 3.1 Requirement

15、s from BS F 100 In addition to the requirements specified in Clause 4, Clause 5, Clause 6, Clause 7 and Clause 8 of this standard the requirements and tests given in the latest edition of BS F 100 as specified in Table 1, shall apply. Table 1 General requirements (given in BS F 100) 3.2 Freedom from

16、 faults The thread shall have uniformity of thickness, construction, and component ply tension so that there are no visually irregular twist faults. The thread shall contain no thread knots. NOTE Up to two laid-on ends per package are permitted. Section of BS F 100 Section title Requirements and tes

17、ts 1 General All requirements 2 a Quality requirements Requirements for dyed textiles except those related to fabric intended for coating Requirements for freedom from corrosive impurities (see BS F 100, Section 4) 3 Physical tests Tests for breaking strength and extension under force 4 Chemical tes

18、ts If required by BS F 100, Section 2: test for conductivity of aqueous extract; test for pH value of aqueous extract; test for water soluble chloride; test for water soluble sulfate. a It is not intended that BS F 100, Section 2 tests should be performed on each thread batch. The frequency of these

19、 tests should be agreed between the Quality Assurance Authority and the thread manufacturer, see BS F 100.BS 5F 58:2002 2 BSI 17 October 2002 3.3 Length per unit mass The length per unit mass of thread shall be determined in accordance with BS EN ISO 2060:1995, Option 1. 4 Yarn The thread shall be m

20、anufactured from combed cotton yarn. 5 Construction and properties 5.1 The construction and properties of the finished thread shall conform to the requirements of Table 2. Table 2 Construction and properties 5.2 The direction of final twist shall be Z. 6 Finish 6.1 Condition of material The thread s

21、hall be supplied scoured, dyed to BS 381C shade 539 and rotproofed with pentachlorophenyl laurate (PCPL) in accordance with BS 2087-1, normal process. NOTE It is very important that the scouring process is thorough in order to remove surface acting agents and processing acids. 6.2 Finish The thread

22、shall have a soft finish. Finishes which promote microbiological growth (e.g. starch or modified starch) shall not be applied. 7 Type test 7.1 General The type test specified in 7.2 shall be carried out to the satisfaction of the quality assurance authority. After initial satisfaction of the type te

23、st, no changes in respect of either the materials or processing conditions used shall be made without the type test being repeated to the satisfaction of the quality assurance authority. The manufacturers records of type tests shall be made available to the quality assurance authority on request. 7.

24、2 Loop breaking strength The thread shall have a minimum average loop breaking strength of 20 N when tested in accordance with BS 1932-2. 8 Identification The thread shall be identified for ordering purposes by the number of this British Standard, i.e. “BS 5F 58”. Designation Structure a Minimum len

25、gth per unit mass Minimum average breaking strength Maximum strength Nominal tex/Turns per m m/kg N N 60/2/3 10 tex 2S 1 3501 650 3Z 530650 13 180 13.3 20 a The twist shall be determined in accordance with BS EN ISO 2061.blankBS 5F 58:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standar

26、ds Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Stan

27、dards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technic

28、al committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying stan

29、dards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international sta

30、ndards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help

31、 to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standard

32、s developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via Brit

33、ish Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except

34、as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the

35、 course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.