BS 6102-12-1991 Cycles - Specification for stem wedge angle《自行车 第12部分 车把主管楔角规范》.pdf

1、BRITISH STANDARD BS 6102-12: 1991 ISO 8562: 1990 Cycles Part 12: Specification for stem wedge angleBS6102-12:1991 This British Standard, having been prepared under the directionof the General Mechanical Engineering Standards Policy Committee, waspublished under the authorityof the Standards Boardand

2、 comes into effect on 28 June 1991 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference GME/25 Draft for comment 89/70616DC ISBN 0 580 19738 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the G

3、eneral Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/25, upon which the following bodies were represented: Association for Consumer Research Association of Consulting Scientists Association of Cycle Traders Bicycle Association of GB British Battery Manufacturer

4、s Association British Cycling Federation British Rubber Manufacturers Association Consumer Policy Committee of BSI Cyclists Touring Club Department of Transport Institute of Trading Standards Administration Royal Society for the Prevention of Accidents Small Electrical Appliances Marketing Associati

5、on Coopted members Amendments issued since publication Amd. No. Date CommentsBS6102-12:1991 BSI 07-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative reference 1 3 Stem wedge angle 1 4 Assembly conditions 1 Figure 1 Untitled 1 Publication(s) ref

6、erred to inside back coverBS6102-12:1991 ii BSI 07-1999 National foreword This Part of BS6102has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee and forms part of a series implementing corresponding international standards in the development of whic

7、h the United Kingdom has played an active part. This standard is identical with ISO8562:1990 “Cycles Stem wedge angle”, which was prepared by Technical Committee ISO/TC149 of the International Organization for Standardization (ISO). Cross-reference. The Technical Committee has reviewed the provision

8、s of ISO4210:1989, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A related British Standard to ISO4210:1989is BS6102-1:1981 “Specification for safety requirements for bicycles”. A British Standard does not purport to inclu

9、de all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages

10、i and ii, pages1and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.ISO8562:1990(E) BSI 07-1999 1 1 Scope This International Standard specif

11、ies the stem wedge angle intended to ensure a secure assembly between the handlebar stem and the fork stem. NOTE 1The wedge angle has the same function as the angle of the expander cone. 2 Normative reference The following standard contains provisions which, through reference in this text, constitut

12、e provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the sta

13、ndard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 4210:1989, Cycles Safety requirements of bicycles. 3 Stem wedge angle The nominal angle, (see Figure 1), of a stem wedge shall be36 . 4 Assembly conditions The assembly of a handlebar ste

14、m with such a stem wedge, fork stem and the expander bolt tightened in accordance with the manufacturers instruction shall comply with the requirements of ISO4210:1989, 2.3.5 and 4.5.3. Figure 1 2 blankBS6102-12:1991 BSI 07-1999 Publication(s) referred to See national foreword.BS 6102-12: 1991 ISO 8

15、562: 1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStan

16、dards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using

17、 this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive

18、the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of

19、those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information serv

20、ices are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details

21、of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Des

22、igns and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard,

23、 of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.