BS 6818-1-1987 Front-mounted linkage and power take-off for agricultural wheeled tractors - Specification for power take-off《农用轮式拖拉机的前部安装联动机构和动力输出装置 第1部分 动力输出装置规范》.pdf

1、BRITISH STANDARD BS6818-1: 1987 ISO8759-1: 1985 Front-mounted linkage and power take-off for agricultural wheeled tractors Part1: Specification for power take-off ISO title: Agricultural wheeled tractors Front-mounted linkage and power take-off Part1: Power take-off UDC631.37:629.11.013.5+629.114.24

2、94BS6818-1:1987 This British Standard, having been prepared under the directionof the Agricultural Machinery and Implements Standards Committee, was published under the authorityofthe Board of BSI and comes into effect on 30 January1987 BSI11-1999 The following BSI references relate to the work on t

3、his standard: Committee reference AGE/6 Draft for comment85/70046DC ISBN 0 580 15690 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Agricultural Machinery and Implements Standards Committee (AGE/-) to Technical Committee AGE/6 upon wh

4、ich the following bodies were represented: Agricultural and Allied Workers National Trade Group Agricultural Engineers Association British Agricultural and Garden Machinery Association Ltd. County Surveyors Society Department of Trade and Industry (Vehicle Division) Forestry Commission Health and Sa

5、fety Executive Home Timber Merchants Association of Scotland Local Authority Organizations Ministry of Agriculture, Fisheries and Food National Farmers Union National Institute of Agricultural Engineering Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.

6、 Date of issue CommentsBS6818-1:1987 BSI 11-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 1 2 References 1 3 Definition 1 4 Requirements and specifications of power take-off 1 Figure Location of power take-off 1 Publications refe

7、rred to Inside back coverBS6818-1:1987 ii BSI 11-1999 National foreword This Part of BS6818 has been prepared under the direction of the Agricultural Machinery and Implements Standards Committee. It is identical with ISO8759-1:1985 “Agricultural wheeled tractors Front-mounted linkage and power take-

8、off Part1: Power take-off” prepared by Technical Committee ISO/TC23, Tractors and machinery for agriculture and forestry, of the International Organization for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable for publication as

9、a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. Wherever the words “part of ISO8759” appear, referring to this standard, they should be read as “Part of BS6818”. The

10、 Technical Committee has reviewed the provisions of ISO4254-1 and ISO730-1, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A related British Standard for ISO730-1 is BS1841 “Attachment of mounted implements to agricultural

11、wheeled tractors” Part2 “Metric units”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. C

12、ross-references International Standard Corresponding British Standard ISO500:1979 BS5861:1980 Specification for rear-mounted power take-offs on agricultural tractors (Technically equivalent) ISO8759-2:1985 BS6818 Front-mounted linkage and power take-off for agricultural wheeled tractors Part2:1987 S

13、pecification for front linkage (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indic

14、ated in the amendment table on the inside front cover.BS6818-1:1987 BSI 11-1999 1 1 Scope and field of application This part of ISO8759 specifies requirements of type, location, direction of rotation and rotational speed for the power take-off (PTO) fitted to the front of agricultural wheeled tracto

15、rs. It applies to the categories of tractors defined in ISO730-1. NOTEPart2 of ISO8759 specifies requirements for the front linkage. 2 References ISO500, Agricultural tractors Power take-off and drawbar Specification. ISO730-1, Agricultural wheeled tractors Three-point linkage Part1: Categories1,2 a

16、nd3. ISO4254-1, Tractors and machinery for agriculture and forestry Technical means for providing safety Part1: General. 3 Definition For the purposes of ISO8759, the following definition applies. 3.1 front of the tractor the leading end of the machine when moving in the normally accepted direction

17、of travel on the road, as exemplified by the relative positions of the seat, steering wheel, controls and road lighting equipment 4 Requirements and specifications of power take-off 4.1 Type and rotational speed The power take-off shall be of type2(35mm,21splines) in accordance with ISO500. The rota

18、tional speed shall be1000min 1 . 4.2 Direction of rotation The power take-off shall rotate clockwise when the end of its axle is viewed from the front of the tractor. 4.3 Location The location of the axis of the power take-off shall lie within the shaded rectangle shown in the Figure. 4.4 Clearance

19、zone around the power take-off The clearance zone around the power take-off shall be in accordance with ISO500. 4.5 Protection of the power take-off The master guard as shown in ISO500 shall be supplied by the manufacturer and be fixed to the tractor, unless an equivalent protective device ensures t

20、he same degree of protection. NOTEFurther requirements are given in ISO4254-1. Figure Location of power take-off2 blankBS6818-1:1987 BSI 11-1999 Publications referred to See national foreword.BS6818-1: 1987 ISO8759-1: 1985 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI i

21、s the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure

22、that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible

23、, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international an

24、d foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Informa

25、tion on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact th

26、e Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:020

27、89967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system o

28、r transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.