ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:309.10KB ,
资源ID:546272      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-546272.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS 6829-1 6-1991 Analysis of surface active agents (raw materials) - General methods - Method for determination of solubility in water《表面活性剂分析(原料) 第1部分 一般方法 第6节 水溶解度的测定方法》.pdf)为本站会员(赵齐羽)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

BS 6829-1 6-1991 Analysis of surface active agents (raw materials) - General methods - Method for determination of solubility in water《表面活性剂分析(原料) 第1部分 一般方法 第6节 水溶解度的测定方法》.pdf

1、BRITISH STANDARD BS 6829-1.6: 1991 ISO 6839:1982 Analysis of surface active agents (rawmaterials) Part1: General methods Section1.6 Method for determination ofsolubility in waterBS 6829-1.6:1991 This British Standard, having been prepared under the directionof the Chemicals Standards Policy Committe

2、e, waspublished under the authorityof the Standards Board and comes into effect on 31October1991 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference CIC/34 Draft for comment91/52314 DC ISBN 0 580 20105 8 Committees responsible for this British Standard T

3、he preparation of this British Standard was entrusted by the Chemicals Standards Policy Committee (CIC/-) to Technical Committee CIC/34, upon which the following bodies were represented: British Association for Chemical Specialities Chemical Industries Association Chemical Industries Association (GO

4、SIP) Department of Trade and Industry (Laboratory of the Government Chemist) Ministry of Defence Royal Society of Chemistry Soap and Detergent Industry Association Amendments issued since publication Amd. No. Date CommentsBS6829-1.6:1991 BSI 12-1999 i Contents Page Committees responsible Inside fron

5、t cover National foreword ii 0 Introduction 1 1 Scope and field of application 1 2 Reference 1 3 Principle 1 4 Reagent 1 5 Apparatus 1 6 Sampling 1 7 Procedure 1 8 Expression of results 2 9 Test report 2 Table 3 Publication(s) referred to Inside back coverBS 6829-1.6:1991 ii BSI 12-1999 National for

6、eword This Section ofBS6829 has been prepared under the direction of the Chemicals Standards Policy Committee. It is identical withISO6839:1982 “Anionic surface active agents Determination of solubility in water”, published by the International Organization for Standardization (ISO). With reference

7、to5.2, precision thermometers complying withBS5074:1974 “Specification for short and long solid-stem thermometers for precision use” aretechnically equivalent to, and may be used in place of, those complying withISO653:1980. Additional information. With reference toclause1, it should be noted that,

8、despite the applicability of the method as stated, in the UK it is considered that the use of the method should be restricted to surface active agent raw materials and not applied to technical products or formulations. With reference toclause4, water complying with grade3 ofBS3978:1987 “Specificatio

9、n for water for laboratory use” is suitable. With reference to theTable, the name recommended in the UK for “sodium lauryl sulfate” is “sodium dodecyl sulfate” (seeBS2474:1983 “Recommendations for names for chemicals used in industry”). A British Standard does not purport to include all the necessar

10、y provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard Corresponding British Standard ISO 607:1980 BS 3762 Analysis of

11、formulated detergents Part1:1983 Methods of sample division (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments inco

12、rporated. This will be indicated in the amendment table on the inside front cover.BS6829-1.6:1991 BSI 12-1999 1 0 Introduction The method described in this International Standard is one of the simplest of the methods which can be used for this purpose; it is sufficiently accurate and is suitable for

13、 a number of practical uses. 1 Scope and field of application This International Standard specifies a method of establishing the curve representing the solubility of an anionic surface active agent in water as a function of temperature, and, consequently, of allowing evaluation of its solubility at

14、a given temperature. The method is applicable both to pure surface active agents and to technical products or formulations of liquid anionic surface active agents, provided that the solutions of these products are optically clear and are not very strongly coloured. NOTEThe determination of solubilit

15、y may be carried out without restriction in the temperature range from0 to90 C; at temperatures lower than0 C, the determination is possible provided that the solution does not freeze. The solubility curve obtained in the case of pure products may possibly allow the Krafft temperature to be determin

16、ed. 2 Reference ISO 607, Surface active agents and detergents Methods of sample division. 3 Principle Preliminary determination on an aqueous solution of known anionic surface active agent concentration of the temperatures at which the solution changes, on heating, from being cloudy to clear and, on

17、 cooling, from being clear to cloudy. Placing in a bath, controlled at a temperature within the range established in the preliminary determination, of two solutions of the same concentration, one being colder and cloudy and the other being warmer and clear, and noting the appearance of the two solut

18、ions at temperature equilibrium. Repetition of the test, varying the temperature of the bath within the range established by the preliminary determination, until the clear solution remains clear and the cloudy solution remains cloudy, or the solutions change very slowly from being cloudy to clear or

19、 vice versa. From the surface active agent concentrations and the limiting temperatures of solubility, plotting the solubility curve. 4 Reagent During the determination, use only distilled water or water of equivalent purity. 5 Apparatus Usual laboratory equipment, and 5.1 Test tubes, made of borosi

20、licate glass, of diameter20mm and length200mm. 5.2 Precision thermometers, complying with the requirements ofISO653. 5.3 Thermostatically controlled water bath, capable of being controlled at5 C to+90 C, to within 0,1 C, with a transparent cell. 6 Sampling The laboratory sample of anionic surface ac

21、tive agent shall be prepared and stored in accordance with the instructions given inISO607. 7 Procedure 7.1 Test portion Weigh, to the nearest0,01g, the quantity of laboratory sample corresponding to one of the surface active agent concentrations to be studied concentrations usually between1 and50%

22、(m/m) then prepare approximately100ml of solution. If the solution contains dispersed impurities, it is advisable to filter it after heating to a temperature higher than that at which it is cloudy. This procedure shall not involve any alteration of the surface active agent concentration. 7.2 Prelimi

23、nary determination Transfer approximately10ml of the test solution(7.1) to a test tube(5.1) and heat it directly over a flame until the solution becomes clear. Allow to cool slowly in the ambient environment until it becomes cloudy, then slowly raise the temperature again, stirring the solution with

24、 a thermometer(5.2), and, as soon as the solution becomes clear, note the temperature (t 1 ). Allow to cool slowly, stirring the solution with the thermometer, and, as soon as the solution becomes cloudy, note the temperature (t 2 ). The temperature range thus determined is generally of the order of

25、10 C. 7.3 Determination of the limiting temperature of solubility Set the thermostatically controlled bath(5.3) at a temperature within the range defined by the preliminary determination(7.2) and keep it constant to within0,1 C.BS 6829-1.6:1991 2 BSI 12-1999 Fill two test tubes(5.1) with the solutio

26、n(7.1), stopper them, adjust their temperatures so that the solution in one becomes clear and the solution in the other becomes cloudy, and then place them in the thermostatically controlled bath. When the temperatures of the two solutions are equal to that of the water bath, note whether the two so

27、lutions are clear or cloudy. If both solutions are clear, lower the temperature ofthe water bath by a few degrees Celsius if both solutions are cloudy, raise it to a slightly higher temperature and repeat the above test. Carry out a third test, or more if necessary, controlling the bath at a tempera

28、ture deduced from the previous tests, until the change in appearance ofthe solutions (cloudy to clear or clear to cloudy) occurs very slowly or the clear solution remains clear and the cloudy solution remains cloudy. A maximum observation period of2 to3h may be adopted. Note the temperature at which

29、 this occurs to thenearest0,1 C, as the limiting temperature ofsolubility. If the appearance of the solutions remains unchanged, take the temperature immediately below that at which the two solutionsremained cloudy. NOTEThe speed with which the limpidity and cloudiness are reversed is a function of

30、the temperaturest 1and t 2determined in7.2 in relation to that of the bath. 7.4 Plotting the solubility curve Repeat the above procedures(7.1, 7.2 and7.3), using different quantities of test portion so as to cover the range of concentrations to be studied. Plotthe solubility curve as a function of t

31、he concentrations and corresponding limiting temperatures of solubility. This curve makes it possible to deduce the solubility of the surface active agent at a given temperature; determine, if required, the Krafft temperature. 8 Expression of results 8.1 Method of calculation Express the solubility

32、of the anionic surface active agent in water, for a given temperature, as a percentage by mass. 8.2 Precision Comparative analyses on samples of three differentsurface active agents, carried out in eight laboratories, have provided the information given intheTable. 9 Test report The test report shal

33、l include the following information: a) all the information necessary for the complete identification of the sample and details of the treatment of the test portion (and, if required, the temperature to which the solution was heated before filtration); b) the reference of the method used (reference

34、to this International Standard); c) the results obtained and the method of expression used: temperature (t 1 ) at which the solution becomes cloudy for the concentration being studied; temperature (t 2 ) at which the solution becomes clear for the concentration being studied; limiting temperature of

35、 solubility for the concentration being studied; d) if necessary, the solubility curve (and the Krafft temperature, if required); e) details of any operations not specified in this International Standard or regarded as optional, together with details of any incidents likely to have affected the resu

36、lts.BS6829-1.6:1991 BSI 12-1999 3 Table Surface active agent Concentration Mean observed limiting temperature of solubility Standard deviation ofreproducibility % (m/m) C C Sodium laurate, purity96,4% 2,5 5 10 20 30 24 27,7 31,7 38,6 42,7 2 1,7 2 1,6 1,6 Sodium lauryl sulphate, purity99% 2,5 5 10 20

37、 30 14 15,3 17 19,8 22,1 1,2 1,6 1,2 1,3 1,4 Sodium alkane sulphonate, purity98% 40 41 42 43 45 13,5 17,7 23 34,7 57,5 1,5 1 2,5 3 3,54 blankBS6829-1.6:1991 BSI 12-1999 Publication(s) referred to Seenational foreword.BS 6829-1.6: 1991 ISO 6839:1982 BSI 389 Chiswick High Road London W4 4AL BSIBritish

38、StandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishS

39、tandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the techn

40、ical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for

41、 all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless ot

42、herwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its product

43、s and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration

44、. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stor

45、ed in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or gra

46、de designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1