BS 7655-4 2-2000 Specification for insulating and sheathing materials for cables - PVC sheathing compounds - General application - General application《电缆用绝缘和铠装材料规范 PVC铠装化合物 一般用途》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 7655-4.2:2000 ICS 29.0

2、35.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Specification for Insulating and sheathing materials for cables Part 4: PVC sheathing compounds Section 4.2: General application IMPORTANT NOTE This section of BS 7655 is to be read in conjunction with BS 7655-0.This Britis

3、h Standard, having been prepared under the direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 November 2000 BSI 11-2000 First published April 1993 Second edition November 2000 The following BSI references relat

4、e to the work on this standard: Committee reference GEL/20/3 Draft for comment 99/240495 DC ISBN 0 580 33197 0 BS 7655-4.2:2000 Amendments issued since publication Amd. No. Date Comments Committees responsible for this British Standard The preparation of this British Standard was entrusted by Techni

5、cal Committee GEL/20, Electric cables, to Subcommittee GEL/20/3, Insulation and sheath, upon which the following bodies were represented: Association of Consulting Engineers British Approvals Service for Cables British Cables Association British Plastics Federation British Rubber Manufacturers Assoc

6、iation Ltd. Department of Trade and Industry (Consumer Safety Unit, CA Division) Electricity Association ERA Technology Ltd. GAMBICA (BEAMA Ltd.) Institute of Fire Prevention Officers London Underground Ltd. Ministry of Defence Queen Mary and Westfield College Railtrack Warrington Fire Research Cent

7、reBS 7655-4.2:2000 BSI 11-2000 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Requirements 1 Bibliography 3ii BSI 11-2000 BS 7655-4.2:2000 Foreword This section of BS 7655 has been prepared by Subcommittee GEL/20/3. It super

8、sedes BS 7655-4.2:1993 which is withdrawn. This section specifies the requirements for general application PVC sheathing compounds Types 5, 6, 9 and 10. This revision brings this section of BS 7655 fully into line with BS 7655-0:1997, including amendment 1:2000 and introduces the new Type 10 compoun

9、d. Test methods are specified in this section of BS 7655 by reference to the latest edition of standards in which they appear. A dated reference to the most recent edition of the relevant standard for each test method is given in BS 7655-0, which is to be read in conjunction with this section. A Bri

10、tish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a fro

11、nt cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.BS 7655-4.2:2000 BSI 11-2000 1 1 Scope This section of BS 7655 specifies the requirements for the general application PVC sh

12、eathing compounds listed in Table 1. The relevant test methods are given in BS EN 60811 and BS 6469. This section is to be read in conjunction with BS 7655-0, which contains essential provisions for the application of this section of BS 7655. Table 1 Types of general application PVC sheathing compou

13、nds Type Maximum material operating temperature General application 8C 5 85 Hard 6 70 General purpose 9 For use over cable operating at a maximum temperature of 908C 10 70 For outdoor use at low temperatures 2 Normative references For the purposes of this section of BS 7655, the requirements of BS 7

14、655-0, 2.1 apply with regard to normative references. The latest editions of the standards giving test methods are listed in the most recent edition of BS 7655-0. 3 Definitions For the purposes of this section of BS 7655 the definitions given in BS 7655-0, clause 3 apply, together with the following

15、. 3.1 PVC combinations of materials, of which polyvinyl chloride is the characteristic constituent, suitably selected, proportioned and treated, which meet the requirements given in the particular specification 4 Requirements The requirements specified for the compounds listed in Table 2 shall be me

16、t when the compound is tested using the test methods listed against each particular requirement. NOTE For cross-references to the latest editions of the test method standards see BS 7655-0, Table 2.2 BSI 11-2000 BS 7655-4.2:2000 Table 2 Test requirements Test Test method in accordance with BS EN 608

17、11 unless otherwise stated Requirements for compound type Section Clause 5 6 9 10 Properties in the state as manufactured 1-1 9.2 Minimum tensile strength (N/mm 2 ) 12.5 6 12.5 10 Minimum elongation at break (%) 125 125 150 150 Properties after ageing in air oven 1-2 8.1.3.1 Temperature (8C) 135 2 1

18、00 28 0 2 Duration (h) 103 24 73 24 73 24 Minimum tensile strength (N/mm 2 ) 12.5 12.5 10 Maximum variation (%) 25 25 20 Minimum elongation at break (%) 125 150 150 Maximum variation (%) 25 25 20 Bending test at low temperature 1-4 8.2 Temperature (8C) 215 2 215 2 215 2 240 2 Requirement no cracks E

19、longation test at low temperature 1-4 8.4 Temperature (8C) 215 2 215 2 215 2 240 2 Minimum elongation without break (%) 20 20 20 20 Impact test at low temperature 1-4 8.5 Temperature (8C) 215 2 240 2 Requirement no cracks no cracks Pressure test at high temperature 3-1 8.2 Temperature (8C) 95 28 0 2

20、9 0 27 0 2 Maximum indentation (%) 50 50 50 50 Resistance to cracking 3-1 9.2 Temperature (8C) 150 2 150 2 150 2 150 2 Requirement no cracks Loss of mass test 3-2 8.2 Temperature (8C) 115 28 0 2 100 28 0 2 Duration (h) 103 24 73 24 73 24 73 24 Maximum loss of mass (mg/cm 2 ) 1.5 2 1.5 2 Hot deformat

21、ion test 1) BS 6469-99.1, clause 10 Maximum deformation (%) 30 65 40 Insulation resistance constant BS 6469-99.2, clause 8 Temperature (8C) 20 22 0 22 0 2 Minimum K value (MV km) 0.0035 0.0035 0.0035 1) Only for specified radial thicknesses less than 0.4 mm. BSI 11-2000 3 BS 7655-4.2:2000 Bibliograp

22、hy See BS 7655-0, 2.2.BS 7655-4.2:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

23、| | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are up

24、dated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

25、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the

26、latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation o

27、f those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information s

28、ervices are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For

29、 details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under th

30、e Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementi

31、ng the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.