ImageVerifierCode 换一换
格式:PDF , 页数:8 ,大小:80.65KB ,
资源ID:547189      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-547189.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS 7948-1-1997 Films for wrapping rubber bales - Non-strippable high melting point films《包装橡胶包用薄膜 不可剥拆的高熔点薄膜》.pdf)为本站会员(lawfemale396)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

BS 7948-1-1997 Films for wrapping rubber bales - Non-strippable high melting point films《包装橡胶包用薄膜 不可剥拆的高熔点薄膜》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 7948 : Part 1 : 1997 I

2、CS 55.040; 83.140.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Specification for Film for wrapping rubber bales Part 1. Non-strippable high melting point filmsBS 7948 : Part 1 : 1997 This British Standard, having been prepared under the direction of the Sector Board for

3、Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 March 1997 BSI 1997 The following BSI references relate to the work on this standard: Committee reference PRI/50 Draft for comment 95/123604 DC ISBN 0 580 27074 2 Amendments issued since pub

4、lication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/50, Natural and synthetic rubbers, upon which the following bodies were represented: British Rubber Manufacturers Association Ltd. C

5、hemical Industries Association Tropical Growers AssociationBS 7948 : Part 1 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover Foreword ii Specification Introduction 1 1 Scope 1 2 Normative references 1 3 Material 1 4 Physical properties 1 Annex A (normative) Determination of

6、melting characteristics of bale wrappings by DSC (differential scanning calorimetry) 2 List of references Inside back coverii BSI 1997 BS 7948 : Part 1 : 1997 Foreword This Part of BS 7948 was prepared by Technical Committee PRI/50. Other Parts of this standard will cover films suitable for low temp

7、erature mixing and strippable films. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. BSI 1997 1 BS 7948 :

8、 Part 1 : 1997 Specification Introduction Considerable quantities of natural and general purpose synthetic rubber are prepared in crumb form. The crumbs are dried and then pressed into bales whilst still warm, at approximately 60 C. The bales are then wrapped in a film and packed, often automaticall

9、y, into crates. The wrapping film should be strong enough to withstand the stresses encountered during the wrapping and packing operations. It should not adhere to the film on the other bales under the combined effects of the heat from the rubber and the weight of the bales. During storage, the rubb

10、er will flow and the film should be able to withstand the stresses generated. Any failure of the film will cause rubber-to-rubber adhesion, which in a 30-bale crate leads to a one-tonne bale. The prime purpose of the film is to keep the bales separate at all times so that they may be easily removed

11、from their packaging for use. However, because it is difficult and uneconomic to strip the film from each bale, an essential feature is that the film should disperse in the rubber compound during mixing. This means that its melting point has to be lower than the temperatures attained in internal mix

12、ing cycles, typically 120 C to 160 C. Unfortunately, there is no acceptable or reproducible dispersal test available to measure this important property directly. Mixes carried out on a two-roll mill or in a single-stage internal mixer cycle might not reach the required temperature for dispersion. If

13、 this happens, then an option would be to strip the film from the bales. Films suitable for low temperature mixing and strippable films will be covered in other Parts of BS 7948. 1 Scope This Part of BS 7948 specifies the material and physical property requirements for non-strippable high melting po

14、int film for wrapping natural and general purpose synthetic rubber bales, intended to keep the bales separate during storage. 2 Normative references This Part of BS 7948 incorporates, by dated or undated reference, provisions from other publications. These normative references are made at the approp

15、riate places in the text and the cited publications are listed on the inside back cover. For dated references, only the edition cited applies: any subsequent amendments to or revisions of the cited publication apply to this Part of BS 7948 only when incorporated in the reference by amendment or revi

16、sion. For undated references, the latest edition of the cited publication applies, together with any amendments. 3 Material The film shall be manufactured from one of: a) low-density polyethylene (polyethene) (PE-LD); b) low-density polyethylene blended with ethylene/vinyl acetate copolymer (E/VAC);

17、 or c) an appropriate grade of E/VAC copolymer. NOTE. Antioxidants, slip agents and anti-blocking agents may be present. 4 Physical properties 4.1 Thickness When measured using a thickness gauge, the film shall have a thickness between 0.035 mm and 0.065 mm. 4.2 Melt flow rate When tested in accorda

18、nce with BS 2782 : Method 720A at 190 C, the melt flow rate shall be greater than 1 g/10 min. 4.3 Vicat softening temperature When tested in accordance with BS 2782 : Method 120A, the Vicat softening temperature shall be no greater than 93 C. 4.4 Melting point by differential scanning calorimetry (D

19、SC) When tested in accordance with the method given in annex A, melting shall be complete before 110 C.BS 7948 : Part 1 : 1997 2 BSI 1997 Annex A (normative) Determination of melting characteristics of bale wrappings by DSC (differential scanning calorimetry) The method falls into two stages; a cali

20、bration phase and a measurement phase. A.1 Calibration Calibrate the DSC over the range of 50 C to 200 C by the use of stearic acid and indium standards which have melting points at 68.0 C and 156.6 C respectively. The two standards are heated individually at the heating rate to be used for the meas

21、urement of the test sample. This is normally at a rate of 20 C/min. On completion of each temperature scan, measure the maximum of the melting endotherm. The peak maxima obtained for the two standards are then input into the instrument calibration program. A.2 Sample measurement Heat the sample over

22、 the required temperature range at the same rate as for the calibration standards. The onset, maximum and end point of the sample melting are then read from the instrument. The onset of melting is defined as the intersection of the baseline and the tangent to the peak. The endpoint is where the peak

23、 ends (returning to the baseline). As a final check on temperature, the indium standard is scanned again and corrections to the sample melting values made where necessary. BSI 1997 BS 7948 : Part 1 : 1997 List of references (see clause 2) Normative references BSI publications BRITISH STANDARDS INSTI

24、TUTION, London BS 2782 Methods of testing plastics BS 2782 : Part 1 Thermal properties BS 2782 : Methods 120A, 120B, 120D and 120E : 1990 Determination of Vicat softening temperature of thermoplastics BS 2782 : Part 7 Rheological properties BS 2782 : Method 720A : 1979 Determination of melt flow rat

25、e of thermoplasticsBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

26、| | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment o

27、r revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would in

28、form the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of s

29、tandards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have be

30、en published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also ava

31、ilable which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these an

32、d other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs

33、 and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of

34、necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1