BS 7F 47-1990 Specification for cotton tape for aerospace purposes《航空航天用棉带规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIESBS 7F 47:1990(Superseding BS 6F 47) Incorporating Amendment No. 1Specification forCotton tape for aerospace purposesNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWConfirmed December 2009BS 7F 47:1990This British Standard, having been prepared u

2、nder the direction of the Aerospace Standards Policy Committee (ACE/-), was published under the authority of the Board of BSI and comes into effect on 31 October 1990 BSI 27 May 2002The following BSI references relate to the work on this standard:Committee reference ACE/21Draft for comment 88/77257

3、DCISBN 0 580 18453 6Committees responsible for this British StandardThe preparation of this British Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/21, upon which the following bodies were represented:British Narrow Fabrics AssociationMinistry of

4、 DefenceSociety of British Aerospace Companies LimitedSociety of Dyers and ColouristsAmendments issued since publicationAmd. No. Date of issue Comments13337 27 May 2002 Indicated by a sidelineBS 7F 47:1990 BSI 27 May 2002iContentsPageCommittees responsible Inside front coverForeword ii1Scope 12 Gene

5、ral requirements 13Yarn 14 Manufacture 15 Finish 16 Construction and properties 27 Identification 2Appendix A Information to be supplied by the purchaser 3Appendix B Deleted 3Table 1 General requirements (given in BS F 100) 1Table 2 Construction and properties of tapes 2Publications referred to 5BS

6、7F 47:1990ii BSI 27 May 2002ForewordThis British Standard, prepared under the direction of the Aerospace Standards Policy Committee, is one of a series for textiles of a quality suitable for aerospace purposes. It constitutes a revision of BS 6F 47:1983 which is withdrawn. It differs from the previo

7、us edition in that reference to the construction and properties of tapes with obsolescent widths has been transferred to an appendix, and the quality requirements defined in the latest edition of BS F 100 are also included as are details of information to be supplied by the purchaser.WARNING NOTES1)

8、 This standard calls for the use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supplier or the user from statutory obligations relating to health and safety at any

9、stage of manufacture or use.2) This standard specifies pentachlorophenyl laurate (PCPL) as the only approved rot-proofing treatment for aerospace fabrics. Alternative treatments are under development, and this standard will be updated to delete PCPL as soon as an approved alternative treatment for a

10、erospace fabrics is available.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pa

11、gesThis document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 5 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Sidelining in this document indicates the most recent changes by amendment.BS 7F 47:1990 BSI

12、27 May 200211 ScopeThis British Standard specifies the requirements for cotton tapes for aerospace purposes in a range of widths.NOTE 1 The information to be supplied by the purchaser in the contract or order is listed in Appendix A.NOTE 2 The titles of the publications referred to in this standard

13、are listed on the inside back cover.NOTE 3 The latest revision of an Aerospace Series standard is indicated by a prefix number.2 General requirementsIn addition to the requirements specified in clauses 3, 4, 5 and 6 of this standard, the requirements and tests of the latest edition of BS F 100 as sp

14、ecified in Table 1 shall apply.Table 1 General requirements (given in BS F 100)3 YarnThe tape shall be manufactured from unsized cotton yarns of the following nominal linear densities:a) warp: 2 ply yarn of resultant linear density 20 tex;b) weft: singles yarn of linear density 20 tex.4 Manufacture4

15、.1 The weave shall be plain.4.2 The webbing shall be woven on shuttle looms. Shuttleless constructions shall not be permitted.5 Finish5.1 GeneralThe tape shall be supplied in one of the following conditions:a) loomstate;b) scoured and rot-proofed;c) scoured, dyed and rot-proofed.NOTE The finish requ

16、ired should be stated in the contract or order (see Appendix A).Section of BS F 100Section title Requirements and testsOne General All requirementsTwo Quality requirements Requirements for manufacture of narrow fabricsRequirements for dyed textiles except those related to fabric intended for coating

17、Requirements for dimensions and tolerancesRequirements for freedom from corrosive impuritiesa(see section 4 of BS F 100)Requirements for freedom from faults in woven narrow fabricsThree Physical tests Test for determination of number of threads per unit length in fabricsTest for determination of the

18、 mass of narrow fabricsTest for breaking strength and extension under forceFour Chemical tests If required by section two:Test for conductivity of aqueous extractTest for pH value of aqueous extractTest for water soluble chlorideTest for water soluble sulfateaApplies only to scoured, dyed or rot-pro

19、ofed fabrics complying with items b) and c) of 5.1.BS 7F 47:19902 BSI 27 May 20025.2 Rot-proofingWhere rot-proofing is required, the tape shall be treated with pentachlorophenyl laurate (PCPL) from aqueous emulsion in accordance with the normal process specified in BS 2087-1, except that the upper l

20、imit for PCPL content shall be 3.5 %.No other rot-proofing agent shall be permitted.5.3 DyeingWhere dyeing is required, the colour shall be specified by reference to a British Standard, e.g. BS 381C, or otherwise by pattern.NOTE The colour required should be stated in the contract or order (see Appe

21、ndix A).6 Construction and propertiesThe construction and properties of the tape shall comply with the requirements of Table 2.NOTE 1 The width required should be stated in the contract or order (see Appendix A).Table 2 Construction and properties of tapes 7 IdentificationThe tape shall be identifie

22、d by the number of this British Standard, i.e. BS 7F 47:19901), together with the width, and, where required, the colour and rot-proofing requirements.NOTE The identification may be codified: For example, 50 mm wide tape dyed olive drab and rot-proofed may be identified as BS 7F 47/50 mm/BS 381C No.

23、 298/PCPL.Width Number of ends in widthaMaximum mass per unit lengthMinimum breaking strengthMinimum number of picks per centimetremm g/m N1015202530324050365772961161201501921.21.92.43.23.94.05.06.4801251602152602653304301717171717171717aTolerance .1)Marking BS 7F 47 on or in relation to a product

24、represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is therefore solely the responsibility of the person making the claim. Such a declaration is not to be confused wi

25、th third party certification of conformity, which may also be desirable.+40BS 7F 47:1990 BSI 27 May 20023Appendix A Information to be supplied by the purchaserThe following information should be stated by the purchaser in the contract or order:a) the number of this British Standard, i.e. BS 7F 47;b)

26、 the type of finish required (see 5.1);c) the colour required, if dyed, (see 5.3);d) the width required (see clause 6).Appendix B Deleted4blankBS 7F 47:1990 BSI 27 May 20025Publications referred toBS F 100, Procedure for inspection and testing of textiles for aerospace purposes.BS 381C, Specificatio

27、n for colours for identification, coding and special purposes.BS 2087, Preservative treatments for textiles.BS 2087-1, Specification for treatments.BS 7F 47:1990BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing Britis

28、h Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the c

29、onstant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

30、 Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addre

31、ssed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published

32、 as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which g

33、ive details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For detai

34、ls of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the B

35、SI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a

36、retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.