BS 9210 N0009-1-1978 Detail specification for radio frequency connectors (series SMC) - Unsealed soldered captive contact 50 $2I screw coupling - Full assessment level《射频连接器(SMC系列).pdf

1、BRITISH STANDARD BS 9210 N0009-1:1978 Incorporating Amendment No. 1 Detail specification for radio frequency connectors (seriesSMC) Unsealed, soldered, captive contact 50 7 screw coupling Full assessment level UDC 621.315.683BS9210N0009-1:1978 BSI 04-2000 ISBN 0 580 10274 2 A British Standard does n

2、ot purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside

3、front cover, pages i and ii, pages 1 to 29 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue Comments 3650

4、 July 1981 Indicated by a sideline in the marginBS9210N0009-1:1978 BSI 04-2000 i Contents Page 1 Physical characteristics 2 2 Ratings (including limiting conditions of use) and characteristics 3 3 Related documents 4 4 Additional information 4 5 Marking of the connectors and packages 4 6 Ordering in

5、formation 4 7 Control drawings 4 8 Inspection requirements 4 Appendix A Outline drawings 17 Appendix B Recommended piercings for metal panels printed wiring boards and overlap dimension 25 Appendix C Recommended grouping of specimens for qualification approval (Group D) testing 27ii blankBS9210N0009

6、-1:1978 BSI 04-2000 1 ELECTRONIC COMPONENTS OF ASSESSED QUALITY: DETAIL SPECIFICATION Typical outlines, styles 07-02 and 06-03 RADIO FREQUENCY CONNECTOR FULL ASSESSMENT LEVEL STYLE 07-02 STYLE 06-03 SERIES SMC UNSEALED, SOLDERED, CAPTIVE CONTACT 50 7 (SCREW COUPLING) For other styles and dimensions

7、see Appendix ABS9210N0009-1:1978 2 BSI 04-2000 1 Physical characteristics 1.1 Style reference number Description Mass (grams) max. Connector variant Cables BS2316/ (URM No.) Cables based on MIL-C-17 (RG No.) (for information only) 01-02 Connector coupler, free, straight, male centre contact 3.5 Matc

8、hed 02-02 Connector fixed, straight, 4-hole fixing, solder bucket, male centre contact 3.0 AB AC AE 110 95 109, 116 178B/U, 404/U 174A/U 316/0 05-02 Connector fixed, single hole front mounting, solder bucket, male centre contact 1.5 06-03 Connector free, straight female centre contact 3.5 07-02 Conn

9、ector fixed, straight, single hole rear mounting, cable outlet, male centre contact 3.1 Unmatched 08-03 Connector free, right angle, female centre contact 5.0 BB 111 179 B/U 10-02 Connector fixed, right angle, 4-hole fixing, solder bucket, male centre contact 8.0 12-02 Connector fixed, right angle,

10、single hole mounting, solder bucket, male centre contact 5.0 ZZ Equipment wire 13-02 Connector fixed, straight, printed circuit board mounting, male centre contact 4.0 14-02 Connector fixed, right angle, printed circuit board mounting, male centre contact 5.5 18-04 Adaptor connector fixed, straight,

11、 single hole mounting, two male centre contacts 3.0 18-05 Adaptor connector fixed, straight, single hole mounting, two female centre contacts 5.0 26-02 Connector fixed, single hole rear mounting, solder bucket, male centre contact 1.5 98-12 Cover protective, for connector fixed and connector coupler

12、 free 3.0 99-12 Cover protective, for connector free 3.0BS9210N0009-1:1978 BSI 04-2000 3 1.2 Body finish Gold (Au), or bright nickel alloy (Ni-). NOTEGalvanic corrosion may occur when connectors are in contact with dissimilar metals. 1.3 Centre contact finish. Gold (Au). 2 Ratings (including limitin

13、g conditions of use) and characteristics Nominal characteristic impedance 50 7 Matched variants Unmatched variants Reflection coefficient (and v.s.w.r.) max. 100 MHz to 4 GHz Above 4 GHz to 10 GHz a) Straight cable outlet styles 0.17 (1.41) 0.25 (1.69) b) Right-angle styles and adaptors, straight No

14、t measured c) Solder-bucket and p.c.b. mounting styles 0.22 (1.57) 0.33 (2.00) Not measured Capacitance (max.) (solder-bucket styles only) 5 pF R.F. shunt resistance (min.) (solder-bucket styles only) 1 M7 at 30 MHz a Working voltage (d.c. or a.c. peak) Inner conductor to shell a) At sea level 500 V

15、 b) At altitude of 20 km (44 mbar) 100 V a Proof voltage (d.c. or a.c. peak) a) At sea level 1500 V b) At altitude of 20 km (44 mbar b ) 300 V Current rating (max.) 0.25 A d.c. Power rating c a Some cables usable with these connectors have ratings lower than the values given here. b 1 mbar = 10 2N/m

16、 2= 0.1 kPa. c As power is dependent on frequency and cable type, for information on power rating refer to the manufacturer. Before conditioning After conditioning Contact resistance, max. 5 m7 10 m7 Outer conductor continuity, max. 2 m7 5 m7 Insulation resistance, min. 5 G7 500 M7 Vibration severit

17、y Frequency range 10 Hz to 500 Hz Displacement 0.75 mm Cross over at approximately 60 Hz Acceleration 98 m/s 2 Duration 6 h Shock severity 490 m/s 2for 11 ms Bump severity 4 000 at 390 m/s 2 Climatic category 55/155/21 Resistance to test prod damage Not applicable Impact severity (free styles only)

18、5 impacts at 1 m Engagement and separation torque 110 mN m max. Normal coupling torque 420450 mN m BS9210N0009-1:1978 4 BSI 04-2000 3 Related documents BS 192, Open-ended wrenches (not including B.A. sizes). BS 1580, Unified screw threads. BS 2011, Basic environmental testing procedures. BS 2316, Ra

19、dio-frequency cables. BS 6000, Guide to the use of BS 6001. Sampling procedures and tables for inspection by attributes. BS 6001, Sampling procedures and tables for inspection by attributes. BS 9000, General requirements for electronic components of assessed quality. BS 9210, Radio frequency connect

20、ors of assessed quality: generic data and methods of test. 4 Additional information (Not for inspection purposes) For recommended piercings for metal panels and printed circuit boards, and overlap dimension seeAppendix B. 5 Marking of the connectors and packages The marking of the component and pack

21、age shall be in accordance with1.1.6 of BS9210. Assembly and cable mounting instructions shall be included in every individual package of connector piece parts. 6 Ordering information In accordance with the requirements of1.1.15 of BS9210, orders for connectors and their accessories covered by this

22、specification shall contain the following information. a) The number of this detail specification, i.e. BS9210 N0009. b) Style as in 1.1, e.g. 0102. c) Variant as in 1.1, e.g. AB. d) Climatic category, i.e. 55/155/21. e) Body finish, e.g. gold (Au). f) Coupling nut. If non-preferred knurled type req

23、uired add/k. g) Any additional information, e.g. fixing hole details, any special marking, or packaging requirements. Example. BS9210 N0009/01-02/AB/55/155/21/Au. 7 Control drawings Control drawings BS 9210 N0009-2, are available from BSI. NOTENormally required by manufacturers and inspectorates onl

24、y. 8 Inspection requirements 8.1 Unless otherwise stated in the table of tests the provisions of8.2, 8.3 and8.4 of this specification shall apply. 8.2 Contact resistance and outer conductor continuity for each mated pair shall be measured using the “light current” method specified in1.2.4.3.3 1) of

25、BS9210. When testing the outer conductor continuity of panel mounted styles, where the connector shell is electrically connected to a mounting plate (see1.2.1.1 of BS9210), the continuity test shall include a measurement between cable braid(s) and the mounting plate. The initial contact resistances

26、for each mated pair of contacts and for any outer conductor path shall not exceed5m7 and2m7 respectively. Resistances after conditioning shall not exceed10m7 and5m7 respectively. 8.3 Insulation resistance measurements between inner conductor and shell shall be made at500 50V d.c. 8.4 Voltage proof m

27、easurements (at sea level) shall be made at1500 100V d.c. or a.c. peak (40Hz to60Hz). There shall be no breakdown or flashover.BS9210N0009-1:1978 BSI 04-2000 5 8.5 For tests in subgroups C3, C5, D3(iii), and D3(v), involving exposure to the upper temperature category, it is essential that cable havi

28、ng a compatible temperature capability shall be used. 8.6 Due to the nature of the accessories referred to in note1 of this specification, certain tests are not possible, e.g.contact resistance tests are not applicable to protective cover styles98-12 and99-12 either before or after conditioning. 8.7

29、 Samples subjected to tests which are marked as “(D)” shall not be accepted for release under BS9000 (see2.6.5 of BS9000-1). 8.8 The tests or measurements prescribed in BS9210 after environmental conditioning are omitted between the environmental conditionings where these form part of a sequence in

30、accordance with1.2.6 of BS9210. The appropriate tests are included at the end of each test sequence. NOTESSee end of table. Inspection BS 9210:1971 reference and conditions of test Performance requirements GROUP A To be applied on a sampling basis lot-by-lot. Subgroups A0, A2, A3 and A4 are not appl

31、icable Subgroup A1 Inspection level S-3, AQL 1.5 % (See note 1 of this specification) Visual examination 1.2.2 2) Either on assembled components or on contents of packages As in 1.2.2 2) of BS 9210 Subgroup A5 CTR information 1.1.11 Attributes information for subgroup A1 GROUP B To be applied on a s

32、ampling basis lot-by-lot. Subgroups B3, B5, B6 and B7 are not applicable. (The specimens used for subgroups B1 and B2 may also be used for subgroup B4.) Connectors shall be assembled in accordance with the instructions supplied by the manufacturer Subgroup B1 Inspection level S-3, AQL 1.5 % Compatib

33、ility-mechanical (assurance) 1.2.5.9 2) See note 1 of this specification As in 1.2.5.9 2) of BS 9210 Subgroup B2 (D) Inspection level S-3, AQL 4 % Soldering 1.2.6.1 Soldering iron method Bit size 3 mm Iron size (b) Centre contact for all styles; also mounting spills for styles 13-02 and 14-02 There

34、shall be no damage or loosening of parts Insulation resistance 1.2.4.6 As in 8.3 of this specification W 5 G7 NOTESSee end of table.BS9210N0009-1:1978 6 BSI 04-2000 Inspection BS 9210:1971 reference and conditions of test Performance requirements Sub group B2 (D) (Continued) Voltage proof 1.2.4.7 As

35、 in 8.4 of this specification As in 8.4 of this specification Subgroup B4 (D) Inspection level S-3, AQL 4 % Engagement and separation 1.2.5.5 See note 1 of this specification As in clause 2 of this specification Gauge retention force 1.2.5.2 See control drawings BS 9210 N0009-2 for details of gauges

36、 As in 1.2.5.2 of BS9210 Subgroup B8 CTR information 1.1.11 Attributes information for subgroups B1, B2, and B4 GROUP C Applied at three-monthly intervals except when group D tests are due. In addition the issue number of the manufacturers drawing list shall be checked against that in the qualificat

37、ion approval application or certificate. Specimens used for subgroup C1 may also be used for subgroups C3 and C5. Subgroups C2 and C4 are not applicable Subgroup C1 Inspection level S-3, AQL 1 % Outline dimensions and mass 1.2.3.1 See note 1 of this specification As in 1.1 and Appendix A both of thi

38、s specification Subgroup C3 (D) Inspection level S-3, AQL 4 % 8.5, 8.8, notes 1 and 2 of this specification apply to tests in this subgroup. Connectors shall be assembled as for group B. Normal coupling torque as in clause 2 of this specification Test prod damage 1.2.5.7 Test not to be applied Rapid

39、 change of temperature 1.2.6.9 55 C and + 155 C followed by Damp heat, steady state 1.2.6.8 Severity 40 2 C for 4 days. Polarizing voltage 60 5V d.c. Inner conductor to be positive. Working voltage 500 50 V d.c. or a.c. peak As in 1.2.6.8 of BS9210. There shall be no breakdown or flashover NOTESSee

40、end of table.BS9210N0009-1:1978 BSI 04-2000 7 Inspection BS 9210:1971 reference and conditions of test Performance requirements Final measurements Contact resistance 1.2.4.3 As in 8.2 of this specification (mated connectors not separated). Not applicable to styles referred to in note 1 of this speci

41、fication As in 8.2 of this specification Outer conductor continuity 1.2.4.4 As in 8.2 of this specification (mated connectors not separated). Not applicable to styles referred to in note 1 of this specification As in 8.2 of this specification Insulation resistance 1.2.4.6 As in 8.3 of this specifica

42、tion. Not applicable to styles referred to in note 1 of this specification W 500 M7 Voltage proof 1.2.4.7 As in 8.4 of this specification. Not applicable to styles referred to in note 1 of this specification As in 8.4 of this specification Visual inspection 1.2.2 As in 1.2.2 of BS 9210 Engagement an

43、d separation 1.2.5.5 Torque as in clause 2 of this specification Subgroup C5 (D) Inspection level S-3, AQL 4 % 8.5, 8.8, notes 1 and 2 of this specification apply to tests in this subgroup. Connectors shall be assembled as for group B. Normal coupling torque as in clause2 of this specification Mecha

44、nical endurance 1.2.7.1 50 operations at not more than 15 per min. Normal coupling torque applies followed by High temperature endurance 1.2.7.2 Severity 155 5 C for 250 h with no electrical load Final measurements Insulation resistance 1.2.4.6 As in 8.3 of this specification. Not applicable to styl

45、es referred to in note 1 of this specification W 500 M7 Contact resistance 1.2.4.3 As in 8.2 of this specification. Not applicable to styles referred to in note 1 of this specification As in 8.2 of this specification NOTESSee end of table.BS9210N0009-1:1978 8 BSI 04-2000 Inspection BS 9210:1971 refe

46、rence and conditions of test Performance requirements Subgroup C5 (D) (Concluded) Outer conductor continuity 1.2.4.4 As in 8.2 of this specification. Not applicable to styles referred to in note 1 of this specification As in 8.2 of this specification Voltage proof 1.2.4.7 As in 8.4 of this specifica

47、tion. Not applicable to styles referred to in note 1 of this specification As in 8.4 of this specification Engagement and separation 1.2.5.5 Torque as in clause 2 of this specification Subgroup C6 CTR information 1.1.11 Attributes information for subgroups C3 and C5 GROUP D (D) D3 tests are to be pe

48、rformed at 3 year intervals. In addition the issue number of the manufacturers drawing list shall be checked against that in the qualification approval application or certificate. Subgroups D1 and D2 are not applicable Selection of specimens The selection of specimens shall conform with the requirem

49、ents for group D tests listed in Table 2 of BS9210-1. When qualification approval is sought for the whole range of styles and variants, seeAppendix C of this specification which makes recommendations for the economic selection of style/variant combinations to be submitted for testing in each of the qualification approval test sequences. Appendix C also gives details of permitted acceptance levels Subgroup D3 (i) See note 1 of this specification Dimensions and materials (piece parts) 1.2.3.2 Three sets of piece parts for the connectors in t