1、BS 9263:2016Intruder and hold-up alarmsystems Commissioning, maintenance andremote support Code of practiceBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Publishing and copyright informationThe BSI copyright notice displayed in this document indicates when the docum
2、entwas last issued. The British Standards Institution 2016Published by BSI Standards Limited 2016ISBN 978 0 580 93636 4ICS 13.310The following BSI references relate to the work on this document:Committee reference GW/1/2Draft for comment 16/30338904 DCPublication historyFirst edition, August 2016Ame
3、ndments issued since publicationDate Text affectedBS 9263:2016 BRITISH STANDARDContentsForeword ii0 Introduction 11 Scope 12 Normative references 13 Terms, definitions and abbreviations 24 Security of communications for remote support and remote systemchecks 45 Inspection, functional testing and com
4、missioning 56 Preventative maintenance 67 Corrective maintenance 88 Remote support 89 Documentation, audit trail and records 9AnnexesAnnex A (normative) Commissioning of an I2) at a pre-programmed time for scheduled remote system checks.b) Manual, on site: A user or alarm company service technician
5、manuallyinitiates a connection from the Ior2) initialization of connection is confirmed by a user or alarm companyservice technician on site;NOTE 1 Use of this method at Grade 4 is only permitted if informationsecurity measures are in place (see 4.5).d) Manual, remote with PSTN or ISDN ring-back: Re
6、mote service personnelmanually initiate a connection from a secure computer to the Ib) remote service personnel log out of the communications software runningon the secure computer before allowing others to use it or leaving itunattended; andc) access to the secure computer/communications software i
7、s promptly barredto personnel leaving employment.4.4 Authentication of communicationBefore data is exchanged between the secure computer and the Ib) detailed records of the checks undertaken and the results;c) details of any changes made to system configuration;d) the identity of personnel carrying
8、out the work;e) identification of the secure computer used in any dialogue;f) details of any temporary disconnection including date, time and reason forthe disconnection and subsequent reconnection;g) the identity of the user/client authorizing such changes/disconnections; andh) monthly and annualiz
9、ed performance records of all preventativemaintenance.NOTE See also Annex B.BRITISH STANDARD BS 9263:2016 The British Standards Institution 2016 9Annex A(normative)Commissioning of an Ib) tamper detection;NOTE 1 Check at least one tamper for correct operation through to the CIE.c) setting and unsett
10、ing;NOTE 2 Offer user(s) refresher system operation training, if required.d) entry and exit procedures;e) power supplies, including any APS;NOTE 3 See Annex C.f) functioning of detectors and HDs;g) environmental conditions for adverse effects;h) operation of WDs;NOTE 4 Operation of self-powered WDs
11、includes removal of hold-off voltage.i) operation of ATS (all paths);j) visual inspection for potential problems (electrical and physical).The equipment should be correctly reinstated after testing.B.3 Remote system checksRemote system checks should include the following:a) interrogate event record
12、and take appropriate corrective action;NOTE 1 This might require a site visit.b) where applicable, check the system has been set and unset;NOTE 2 This can be taken from the event record.c) check no adverse tamper or fault conditions exist on the system where thesystem has this capability;d) check an
13、y alarm circuits that are on soak test;e) check any alarm circuits that are inhibited/isolated;f) ensure time and date of clock are correct, update if required;g) check PPS is available;h) check health of any APS;i) check that “frequently used” detectors are operating;j) check operation of ATS (all
14、paths).BRITISH STANDARD BS 9263:2016 The British Standards Institution 2016 11Annex C(informative)Calculation of standby battery capacityC.1 GeneralTo calculate the battery capacity, it is necessary to take two current readings:a) the current when there is no alarm present. This is known as the quie
15、scentcurrent; andb) the current when in alarm with all WDs and ATE activated. This is known asthe alarm current.NOTE 1 The two different readings are required as the standby battery needs to becapable of providing power for the required duration including two periods whenthe system is in a full alar
16、m condition.NOTE 2 Each alarm period can have WDs activated for 15 min.(see BS EN 50131-1:2006+A1:2009, 8.6)C.1.1 Example of time period required in quiescent and alarm conditionIf the required standby period is 12 h, as required at Grade 2, then the batteryneeds to be capable of providing sufficien
17、t power for 11.5 h at the quiescentcurrent +0.5 h (2 15) min at full alarm current.NOTE 1 If the standby period was 24 h then the time periods would be 23.5 hquiescent and 0.5 h in alarm.The battery capacity can then be calculated as follows:C = 1.25 (I1 T1) + (I2 T2)where:C minimum capacity of batt
18、ery in Ampere hours (Ah)1.25 ageing factor (this represents a 25% deficit in battery life overthe expected life of the battery)I1 Quiescent current (A)T1 Quiescent standby time (h)I2 Alarm current (A)T2 Alarm standby time (h)NOTE 2 This calculation assumes that the control equipment and associated P
19、SUsare type A (as described in BS EN 50131-1:2006+A1:2009), i.e. mains supply, and analternative power source recharged by the control equipment/ PSU, where thealternative power source is a lead acid battery.BRITISH STANDARDBS 9263:201612 The British Standards Institution 2016C.1.2 Example of batter
20、y calculationA Grade 2 intruder alarm system with a quiescent current of 250 mA, alarmcurrent of 750 mA (from above the standby period is 12 h with an assumedperiod of 30 min in alarm condition):Quiescent load =I1T1= 0.25 11.5 = 2.875 AhAlarm load =I2T2= 0.75 0.5 = 0.375 AhC= 1.25 (2.875 + 0.375)C =
21、 1.25 3.25C = 4.06 AhThe next highest available battery is to be used.C.2 Measuring current on a I&HASC.2.1 Example measurementAn example of how to measure the quiescent current and alarm current of atypical intruder control panel is given in C.2.2 and C.2.3.C.2.2 Quiescent current (non-alarm condit
22、ion)C.2.2.1 Using a suitable test meter, such as a digital volt meter (DVM), set themeter to read DC Amps (select a high range such as 10 A).C.2.2.2 Disconnect the positive charge lead from the battery terminal (normally apush on receptacle).C.2.2.3 Connect the DVM in series between the positive bat
23、tery terminal and thedisconnected battery lead.C.2.2.4 Disconnect the mains supply to the control panel.C.2.2.5 The total current drawn by all equipment supplied by the control panelPSU is displayed on the DVM.NOTE Typical readings could be between 0.2 A (200 mA) and 0.5 A (500 mA).C.2.3 Alarm curre
24、nt (alarm condition)Repeat the procedure in C.2.2 with the system in full alarm state, e.g. with WDssounding and ATE signalling.NOTE A typical reading could be between 0.4 A (400 mA) 0.7 A (700 mA).BRITISH STANDARD BS 9263:2016 The British Standards Institution 2016 13BibliographyStandards publicati
25、onsFor dated references, only the edition cited applies. For undated references, thelatest edition of the referenced document (including any amendments) applies.BS 47371), Intruder alarm systems in buildingsBS 67991), Code of practice for wire-free intruder alarm systemsBS 70421), Specification for
26、high security intruder alarm systems in buildingsFurther readingBS 7671, Requirements for electrical installations IET Wiring RegulationsBS 8243, Installation and configuration of intruder and hold-up alarm systemsdesigned to generate confirmed alarm conditions Code of practiceBS EN 50131-5-3, Alarm
27、 systems Intrusion systems Part 5-3: Requirements forinterconnections equipment using radio frequency techniques1)Withdrawn.BRITISH STANDARDBS 9263:201614 The British Standards Institution 2016This page deliberately left blankBSI is the national body responsible for preparing British Standards and o
28、ther standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, inno
29、vators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose s
30、tandards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy
31、and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be order
32、ed from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has
33、formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion
34、 thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more tha
35、n 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for person
36、al or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscriptio
37、n product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription prod
38、ucts go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive subs
39、tantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or repl
40、aced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as they
41、re available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy
42、 or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1