BS A 330-1999 Nuts anchor self-locking floating two lug with incremental counterbore with MJ threads classifications 900 MPa (at ambient temperature) 235 C 900 MPa (at ambient temp.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS A330:1999 ISO12272: 1998 Nuts, anchor, self-locking, floating, two lug, with incremental counterbore, with MJ threads, classifications: 900MPa (at ambient temperature)/235 C, 900MPa (at ambient temperature)/315 C and900MPa (atambient temperature)/425C Dimensions

2、ICS 49.030.30BSA330:1999 This BritishStandard, having been prepared under the directionof the Engineering SectorCommittee, was publishedunder the authorityofthe Standards Committee and comes into effect on 15April1999 BSI02-2000 ISBN 0 580 30330 6 National foreword This BritishStandard reproduces ve

3、rbatim ISO12272:1998 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee ACE/12, Aerospace fasteners and fastener systems, to Subcommittee ACE/12/1, Aerospace fasteners and fastener systems (international), which has the respons

4、ibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A lis

5、t of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The BritishStandards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internati

6、onal Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Brit

7、ish Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theISO title page, pagesii to iv, pages1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had am

8、endments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSA330:1999 BSI 02-2000 i Contents Page National foreword Inside front cover Foreword iii Text of ISO12272 1ii blankBS A 330:1999 ii BSI 02-2000 C

9、ontents Page Foreword iii Introduction 1 1 Scope 1 2 Normative references 1 3 Configuration and dimensions 1 Figure 1 2 Table 1 3 Descriptors: Aircraft industry, fasteners, MJ threads, nuts (fasteners) anchor nuts, self-locking nuts, two lug nuts, floating nuts, counterbore nuts, classification, for

10、m specifications, dimensions.BS A 330:1999 BSI 02-2000 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committ

11、ees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Int

12、ernational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member b

13、odies casting a vote. International Standard ISO12272 was prepared by Technical Committee ISO/TC20, Aircraft and space vehicles, Subcommittee SC4, Aerospace fastener systems.iv blankBS A 330:1999 BSI 02-2000 1 Introduction The dimensions specified in this International Standard have been determined

14、to allow production of a part which will satisfy the requirements of the procurement specification ISO5858. 1 Scope This International Standard specifies the dimensions of self-locking, floating, two lug anchor nuts, with incremental counterbore, with MJ threads, for classifications: 900MPa 1) /235

15、C 2) ,900MPa 1) /315 C 2) and900MPa 1) /425 C 2) . This International Standard is only applicable for the compilation of aerospace product standards. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International S

16、tandard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members o

17、f IEC and ISO maintain registers of currently valid International Standards. ISO5855-2:1988, Aerospace MJ threads Part2: Limit dimensions for bolts and nuts. ISO5858:1991, Aerospace Self-locking nuts with maximum operating temperature less than or equal to425C Procurement specification. ISO8788:1987

18、, Aerospace Fasteners Tolerances of form and position for nuts. 3 Configuration and dimensions See Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres. They apply after any surface coating(s) but before the application of any lubricant. 1) Corresponds to the minimum tensile

19、stress which the nut is able to withstand at ambient temperature without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been

20、 restored. The maximum temperature is conditioned by the material or by the surface treatment.BS A 330:1999 2 BSI 02-2000 NOTETolerances of form and position shall conform to those specified in ISO8788. Details of form not stated are at the manufacturers option. 1)These values, in micrometres, apply

21、 before any surface coating(s) is(are) applied. The values do not apply to threads, punched holes or sheared edges, the surface texture of which will be as achieved by the usual manufacturing methods. 2)Tooling marks permissible in this area. Figure 1 BS A 330:1999 BSI 02-2000 3 Table 1 Diameter cod

22、e Thread a E F G H J bK L M N P R S T Radial floating min. min. max. max. max. max. max. min. max. Z min. 050 MJ5 0,84H6H 9,5 19 5,2 4 7,3 12 25,2 8,5 0,9 6,5 3 2,5 4,5 0,5 6 10,5 8 12,5 10 14,5 060 MJ6 14H5H 11 22 6,2 4 8,7 13,5 29,2 9,4 0,9 7,5 3,5 2,5 4,6 0,5 6 11,4 8 13,4 10 15,4 080 MJ8 14H5H 1

23、1 22 8,2 4 10,9 16 29,2 11,2 1,1 9,5 3,5 3 5,5 0,5 6 13,2 8 15,2 10 17,2 a In accordance with ISO5855-2. In the self-locking zone, the tolerances apply before forming out-of-round. b Measured at sharp corners (chamfered) or point of tangency (radiused). + 0,2 0BS A330:1999 ISO12272: 1998 BSI 389 Chi

24、swick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by

25、amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard

26、 would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions o

27、f standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been

28、published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also availab

29、le which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other be

30、nefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act

31、 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary detail

32、s such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.